rizoma EE167 Wiring Kit User Manual
- June 8, 2024
- rizoma
Table of Contents
rizoma EE167 Wiring Kit User Manual
Introduction
Before you start
We are pleased to welcome you into the world of RIZOMA, and we congratulate
you for your excellent choice.
Please carefully follow the instructions in this guide, which will allow you
to mount and use the product correctly and enjoy all the features it has.
For your protection and safety, RIZOMA expressly recommends that you have the
installation of the product performed by skilled personnel.
Improper installation, repair or maintenance, can cause accidents.
Keep this user guide as a reference for the future.
RIZOMA accepts no liability for any damage, of any kind, which may be caused,
directly or indirectly, to persons or things as a result of incorrect assembly
or failure to observe all the assembly instructions.
We also invite you to comply with the provisions of the Highway Code and
Traffic rules and/or to additional regulations in force in your Country.
Attention: This component comes assembled for shipping purposes only.
Tighten all fasteners to appropriate torque specifications before riding.
Descriptions preceded by this symbol contain information, instructions, or
procedures, which, if not followed, may result in death or serious injury.
-
Carefully read, understand and follow these instructions, they are an essential part of the product.
If you have any doubt whatsoever regarding the installation or use of your RIZOMA product, please see your authorized RIZOMA dealer for assistance (on www.rizoma.com). -
For correct installation, all tightening has to be done after the correct positioning of the accessories without restricting the moving parts, to not compromise the correct functioning of the product.
-
After installing any Rizoma product, please check that all related components of the motorbike function e.g. brakes, throttle, clutch, lights and steering.
We strongly suggest to repeat these checks periodically, especially after long trips or prolonged periods of not using the bike.
Your RIZOMA products require regular inspection and maintenance.
The more you ride the more often you must inspect your RIZOMA products.
If your products are leaking, bent, deformed, cracked, chipped or worn, no
matter how slight, immediately have a RIZOMA dealer inspect the products
before you ride again.
In any case never try to repair or modify the Rizoma products or their
components, always replace with Rizoma original components.
Rizoma products may not be compatible with your motorcycle or with other
aftermarket equipment installed before.
For your safety Rizoma suggests to always contact your RIZOMA dealer.
O.E.M.: original equipment manufacturer.
Electric wirings
The use of the EE167H wiring kit together with sequential turn signal lights
does not guarantee the front position light (daytime running light) feature if
it is integrated into the turn signal lights.
N°01 resistor da 100 ohm 2 watt, n°01 resistor 47 ohm 3 watt and n°01 resistor
65 ohm 3 watt.
-
Before you start mounting the product please check the completeness of the kit on the part list.
The difficulty level and the time of assemblage shown do not include the removal of OEM components.
The warrantee is not valid for any electric wires cutting or any product modify or tampering.
-
Improper installation could damage the electrical system of the motorcycle and cause a fire, resulting in personal injury or death.
Electrical shock hazard.
Disconnect the battery before starting to install turn license plate bracket or rear light or the turn signals.
The pins must always be isolated and respect the polarity in the connections.
The warrantee is not valid for any electric wires cutting or any product modify or tampering
DIFFICULTY LEVEL
Simple
**TIME OF ASSEMBLAGE
3-5 min
**
INSTALLATION
Step 1:
Your guarantee will not apply if the turn signal has not been correctly
installed and connected to the electrical supply on your motorbike.
Do not carry out the installation unless you are specifically trained to do
so; otherwise, please contact an authorized dealer Rizoma.
Your guarantee does not apply to damage due to wrong connection or excess
voltage.
Improper mechanical installation or orientation of the turn signal may
invalidate your motorbike’s roadworthiness and insurance protection, or even
lead to accidents.
Check that your turn signal are securely fitted before you ride your
motorbike.
Make sure that your motorbike is standing firmly before you start work, as a
fall may lead to damage to the motorbike or injury to you or others.
Step 2:
Disconnect the battery before starting to install the resistors.
To avoid damage to the electrical system of the bike, for electrical
connection of turn signal and resistor we recommend using the Rizoma electric
wiring.
Consult the Rizoma catalog or the web site
www.Rizoma.com to choose the correct electric wiring.
Arrange the wires to protect them from splash water and fasten them as
appropriate, such as with wire connectors.
Reconnect the motorbike battery and test the turn signal.
Align the turn signal as described above. Install the resistors in such a way
that heat can escape effectively.
These measures may disable the rapid flashing function to alert the rider that
one of the turn signal is no longer working.
Check your turn signal before each motorcycle trip.
These resistors will heat up if the turn signal is used for an extended
period.
Make sure that other components or person are safe.
Step 3:
Warnings
-
RIZOMA reserves the right, in its sole discretion, to make changes to the product and this information at any time and without prior notice.
Although many catalogs and advertisements depict riders engaged in extreme or stunt riding, this activity is extremely dangerous, increases the risk of an accident, and increases the severity of any injury. -
The action depicted is performed by professionals under strictly controlled riding conditions.
-
Only you know the limits of your riding ability and only you can control the conditions under which you ride.
By and in consideration for his/her purchase and use of the RIZOMA product, the user expressly recognizes and agrees that in the event of any claim arising out of the use of this RIZOMA product, whether such claim is based in contract, warranty, tort (personal injury or wrongful death) or otherwise, the laws of the Republic of Italy shall apply and jurisdiction and venue for any such action shall be in the Courts of Busto Arsizio, Italy. -
All riders are strongly urged to take a motorcycle rider safety clinic. Always wear a properly fitted and fastened motorcycle helmet (RIZOMA recommends a full face helmet), that has been approved by ANSI , SNELL, CE, or any other relevant authority, and any other safety equipment necessary for your riding style, such as full finger gloves, boots, and body armor.
-
Be sure to read and follow all the instructions and warnings that originally accompanied your motorcycle, as well as the literature that accompanied any other component parts installed on your motorcycle.
-
Be sure that your tires are inflated to the correct pressure and that there is no damage whatsoever in the tread or sidewall of the tire.
Legal notes
Some of our products may not be approved for road circulation in the countries
where homologation is required.
Thus RIZOMA® srl declines any responsibility for a different use of its
products.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>