SDHQ 70-1206-G4 Silverado/Sierra A-Pillar Light Mounts Instruction Manual

June 9, 2024
SDHQ

SDHQ logo G4 SilveradoSierra A-Pillar Light Mounts
Instruction Manual

Product Packing List

Product: SDHQ-70-1206-G4
Description: Gen 4 Silverado/Sierra A-Pillar Light Mounts 2019+ 1500, 2020+ 2500/3500

(1) Driver Side Mount
(1) Passenger Side Mount
(1) Driver Side Support Bracket
(1) Passenger Side Support Bracket
(2) Aluminum Spacers
(1) Hardware Package
(2) M8 – 1.25 x 60mm S.S. Hex Head Bolt
(2) 5/16” S.S. Washer
(2) ¼” – 20 x ¾” S.S. Button Head Bolt
(2) M6 – 1.0 x 20mm S.S. Button Head Bolt
(4) ¼” S.S. Washer (2) ¼” – 20 x 17/32” Clip on Barrel Nut
(2) SDHQ Silicone Protective Pads
SDHQ-70-1206-G4-A
SDHQ-70-1206-G4-B
SDHQ-70-1206-G4-C
SDHQ-70-1206-G4-D
SDHQ-70-1206-G4-E
SDHQ-70-1206-G4-F

INSTALLATION INSTRUCTIONS

Product: SDHQ-70-1206-G4
Description: Gen 4 Silverado/Sierra A-Pillar Light Mounts.

SDHQ 70 1206 G4 Silverado Sierra A Pillar Light Mounts
-

Parts List Hardware List Required Tools

(1) Driver Side Mount SDHQ-70-1206-G4-A.
(1) Passenger Side Mount SDHQ-70-1206-G4-B.
(1) Driver Side Support Bracket SDHQ-70-1206-G4-C
(1) Passenger Side Support Bracket SDHQ-70-1206-G4-D.
(2) Aluminum Spacer SDHQ-70-1206-G4-E
(1) Hardware Package SDHQ-70-1206-G4-F| (2) M8 – 1.25 x 60mm S.S. Hex Head Bo(2) 5/16” S.S. Washers.
(2) ¼” – 20 x ¾” S.S. Button Head Bolt(2) M6 – 1.0 x 20mm S.S. Button Head Bo(4) ¼” S.S. Washer.
(2) ¼” – 20 Clip on Barrel Nut.
(2) SDHQ Silicone Protective Pads.| 10mm, 13mm Short Drive Socket
13mm offset Ratcheting Wrench
Extension
¼” Ratchet
Torx T30 Bit
Hood Prop
Blue Painters Tape
5/32” and 4mm Hex Drive
Sharpie
Flush Cut Pliers
Razor Blade

Tech Notes
Use Anti-Seize on all Stainless Steel (S.S.) hardware.
Trimming of cowl end caps is required.
Does NOT fit 2019+ GMC 1500. See SDHQ-77-1206-S4.
HD 2500/3500 trucks will NOT use support brackets; see exploded views below.
Approx. Install Time: 1 Hour.

SDHQ 70 1206 G4 Silverado Sierra A Pillar Light Mounts - Driver
Side

READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION!
Installation Instructions:

  1. Unbox and verify all parts are accounted for. Familiarize yourself with the parts and diagrams.

  2. Locate (2) Silicone Protective Pads provided in the hardware kit. Install on mounts as pictured below (make sure surface is clean for best adhesion). Remove the clear hard plastic cover. Install the ¼” – 20 x 17/32” Clip on Barrel Nuts onto support brackets as shown below.
    SDHQ 70 1206 G4 Silverado Sierra A Pillar Light Mounts - Driver
profesanal

  3. Apply masking tape to hood and fender where you will be working. Remove antenna. Open the hood and remove the foam cowl end caps. Support the hood with a hood prop. Remove the (2) 10mm head bolts securing the antenna mount.SDHQ 70 1206 G4 Silverado Sierra A Pillar Light Mounts - Driver Side1

  4. Starting on the driver side, remove the bolt circled below using a short 13mm socket and ¼” ratchet, or 13mm wrench. Remove the Torx T30 head bolt circled below.
    SDHQ 70 1206 G4 Silverado Sierra A Pillar Light Mounts - Driver
Side2

  5. Carefully lower the driver side mount between the hood hinge and fender. Once lowered, insert (1) M8 bolt and (1) 5/16” washer through the lower mounting slot. Place (1) aluminum spacer between the mount and the hood hinge. Begin threading the M8 bolt.

  6. Chevy 1500 owners will need to proceed to Step 9. Chevy/GM 2500/3500 owners can proceed to the next step. 2500/3500 owners will NOT use support brackets provided.

  7. Chevy/GM 2500/3500: Align the rear slot on the mount to the threaded hole from Step 4. Thread (1) M6 bolt and (1) ¼” washer into the threaded hole. Adjust the mount such that the top is flat with the ground and tighten both M6 and M8 hardware. Support Brackets not used.
    SDHQ 70 1206 G4 Silverado Sierra A Pillar Light Mounts - Driver
Side3

  8. Repeat Steps 4-7 for the passenger side. Once the mount is tight, tighten the (2) 10mm head bolts securing the antenna mount to the truck. Proceed to Step 11.
    SDHQ 70 1206 G4 Silverado Sierra A Pillar Light Mounts - Driver
Side4

  9. Chevy 1500: Position the driver side support bracket as shown. Thread (1) M6 bolt and (1) ¼” washer into the threaded hole to secure the support bracket. Align the driver mount and support bracket. Thread (1) ¼” bolt and washer through the mount and into the support bracket. Adjust the mount such that the top is flat with the ground and tighten all hardware. (Hardware shown in the picture to right is not correct)

  10. Repeat Steps 4, 5 and 9 for the passenger side. Once the mount is tight, tighten the (2) 10mm head bolts securing the antenna mount to the truck.

  11. With both A-Pillar mounts installed, install and wire your lights. Bigger lights such as a Baja XL series will mount to the outer slot.

  12. Trimming Cowl End Caps: Position the driver side cowl end cap on the fender as if you were going to install it. Mark 1/8” outside of where the cowl will contact the mount or wire. Remove the cowl end cap. Remove ¼” of material between the marks. Repeat for the passenger side.
    SDHQ 70 1206 G4 Silverado Sierra A Pillar Light Mounts - Driver
Side6

  13. Install the trimmed cowl end caps and antenna. Finish wiring your lights and enjoy your new SDHQ A-Pillar Light Mounts!

Double check all hardware is installed correctly and tight
**Re-torque ALL bolts after 100 miles
**

190 S McQueen Rd
Ste 109 Gilbert, AZ 85233.
Phone: 480-633-2929.
Fax: 480-633-1791.
www.sdhqoffroad.com
Follow us on:
Facebook

Instagram
For questions or help with the installation, please email help@sdhqoffroad.com.
Store front hours: Mon. – Fri. 8:00am – 5:30pm and Sat. 9:00am – 2:00pm Arizona Time.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SDHQ User Manuals

Related Manuals