DYNATRAC DT926523 2.0 Aluminum Series Front Shock Instruction Manual

DYNATRAC DT926523 2.0 Aluminum Series Front Shock

Product Information

• Product Name: 18-UP JL/20-UP JT 2.0 Aluminum Series Front Shock
• Part Number: DT926523
• Description: This product is a high-quality rebuildable race-style shock absorber designed for optimal performance. It is specifically designed for use on 2018 and newer Jeep Wrangler JL models and 2020 and newer Jeep Gladiator JT models. The shock absorber is made from aluminum for durability and is factory-charged to 150 PSI with nitrogen.

Components Included:

• (1) DT124935 18-UP JL/20-UP JT 2.5 LIFT 2.0 FRONT SHOCK
• (2) 209208 STEPPED SHOCK SLEEVE .625 X .480 X 2.750

Hardware Included: N/A

Tools Required: Torque Wrench, 18mm Socket/Wrench
Technical Notes: It is important to note that a minimum of a 1 bump stop spacer is required for installation (supplied with Dynatrac coil spring kit PN: DT922025). Releasing nitrogen pressure from the shock absorber may lead to shock malfunction and reduced ride quality. Failure caused by low nitrogen pressure is not covered under Dynatrac’s warranty policy.

Product Usage Instructions

1. Place the vehicle on a smooth, level surface. Ensure that the vehicle is in PARK, engage the emergency brake, and chock the tires before performing any work to the vehicle. Failure to do so may result in severe frame, suspension, and tire damage.
2. Remove the factory shock using an 18mm socket or wrench (refer to FIG.1 for reference).
3. Using factory hardware and an 18mm socket or wrench, install the Dynatrac front shock (refer to FIG.2 for reference). Torque all fasteners to factory specifications.
4. Verify that all fasteners are properly torqued before driving the vehicle.
5. After driving 100 miles, I retrieved all the nuts, bolts, and lugs. Repeat this periodically thereafter.

Maintenance

Dynatrac shock absorbers require routine maintenance to keep them looking and operating in like-new condition. It is normal for residual oil and assembly lube to be present at all seal paths from the factory. However, the pooling of oil is not acceptable. If pooling of oil occurs, contact the Dynatrac dealer where the product was purchased.

The maintenance guidelines vary based on how the vehicle is used:

• Street Use: Contact Dynatrac for service kits and tools.
• Street/Dirt Use: Contact Dynatrac for service kits and tools.
• Dirt Use: Contact Dynatrac for service kits and tools.

Warranty Information

Dynatrac Shock Absorbers are covered by a warranty. For more information regarding the warranty or to inquire about service kits and tools, please contact Dynatrac at:

• Phone: 714-596-4461
• Website: www.dynatrac.com.

PART DESCRIPTION

2.0 ALUMINUM SERIES FRONT SHOCK

COMPONENTS INCLUDED

__

__

(1) DT124935 18-UP JL/20-UP JT 2.5” LIFT 2.0 FRONT SHOCK

| __

__

(2) 209208 STEPPED SHOCK SLEEVE .625 X .480 X 2.750

HARDWARE INCLUDED
__

__

N/A

|
TOOLS REQUIRED
__

__

TORQUE WRENCH

| __

__

18MM SOCKET / WRENCH

TECH NOTES
__

__

1. A MINIMUM OF A 1” BUMP STOP SPACER IS REQUIRED (SUPPLIED WITH DYNATRAC COIL SPRING KIT PN: DT922025).

__

2. YOUR DYNATRAC SHOCK ASSEMBLIES COME FACTORY CHARGED TO 150 PSI. RELEASING NITROGEN PRESSURE MAY LEAD TO SHOCK MALFUNCTION AND REDUCED RIDE QUALITY. FAILURE CAUSED BY LOW NITROGEN PRESSURE IS NOT COVERED UNDER DYNATRAC’S WARRANTY POLICY.

WARNING!

• READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION! IF THESE INSTRUCTIONS ARE NOT PROPERLY FOLLOWED SEVERE FRAME, SUSPENSION AND TIRE DAMAGE MAY RESULT TO THE VEHICLE!
• DYNATRAC RECOMMENDS THAT YOU EXERCISE EXTREME CAUTION WHEN WORKING UNDER A VEHICLE THAT IS SUPPORTED WITH JACK STANDS.
• DYNATRAC RECOMMENDS ALL INSTALLATION TO BE PERFORMED BY A PROFESSIONAL SHOP/SERVICE TECHNICIAN. PRODUCT FAILURE CAUSED BY IMPROPER INSTALLATION WILL NOT BE COVERED UNDER DYNATRAC’S WARRANTY POLICY.

INSTALLATION

1. Place the vehicle on a smooth, level surface. Ensure that the vehicle is in PARK, engage the emergency brake, and chock the tires before performing any work to the vehicle. DYNATRAC will not be held liable for any injuries or failure casued by improper installation.
2. Remove the factory shock using an 18mm.
3. Using factory hardware and an 18mm, install the DYNATRAC front shock. [Torque to factory spec]

VERIFY ALL FASTENERS ARE PROPERLY TORQUED BEFORE DRIVING THE VEHICLE. RETORQUE ALL NUTS, BOLTS, AND LUGS AFTER 100 MILES AND PERIODICALLY THEREAFTER.

ALUMINUM SERIES TECHNICAL INFORMATION

MAINTENANCE

DYNATRAC shock absorbers are high-quality rebuildable race-style shock absorbers designed for optimal performance. With a unit of this caliber on your vehicle, routine maintenance is required to keep them looking and operating in new conditions. Residual oil and assembly lube may be present at all seal paths from the factory out of the box and is considered normal. Pooling of oil however is not acceptable at any time and one should contact the DYNATRAC dealer where purchased.
BELOW ARE GUIDELINES BASED ON HOW YOU USE YOUR VEHICLE BUT YOUR MILEAGE MAY VARY:

STREET USE:

• Send in for factory servicing every 40,000 miles or if a leak develops, ride quality decreases, or they begin to make excessive noise.
• Remove any buildup of road salt, mud, or debris from shocks anytime accrued
• Clean with mild soap and water with each oil change or any time you notice build-up.
• Wax the cylinders yearly with automotive wax to prevent corrosion.
• Check nitrogen pressure yearly.

STREET/DIRT:

• Send in for factory servicing every 15,000 miles or if a leak develops, ride quality decreases, or they begin to make excessive noise.
• Clean with mild soap and water with each oil change, offroad trip, or any time you notice build-up.
• Wax the cylinders yearly with automotive wax to prevent corrosion.
• Check nitrogen pressure for each dirt outing.

DIRT USE:

• Send in for factory servicing every 1,000 miles.
• Check nitrogen pressure each outing.
• Remove any buildup of mud or debris from shocks after every outing.

SELF-SERVICE:

• Contact DYNATRAC for service kits & tools at 714-596-4461.

DYNATRAC SHOCK ABSORBER WARRANTY

• This shock absorber has a 1-year warranty against any manufacturer’s defects. If a shock fails within the initial year of ownership, the shock must be shipped to DYNATRAC for inspection and service. If a shock is inspected and it has been determined the shock failed due to neglect, damage caused by improper installation, or any other reason besides “normal wear and tear”, the owner of said shock is responsible for all service costs. This includes labor, parts, and shipping.
• DYNATRAC warrants to the original retail purchaser who owns the vehicle on which the product was originally installed. DYNATRAC does not warrant the product for finish, alterations, modifications, and/or installation contrary to DYNATRAC instructions. DYNATRAC products are not designed, nor are they intended to be installed on vehicles used in race applications, for racing purposes or for similar activities. (A “race” is defined as any contest between two or more vehicles, or a contest of one or more vehicles against the clock, whether or not such contest is for a prize). This warranty does not include coverage for police or taxi vehicles, race vehicles, or vehicles used for government or commercial purposes. Also excluded from this warranty are sales outside of the United States of America and Canada.
• DYNATRAC’S obligation under this warranty is limited to the repair or replacement, at DYNATRAC’S discretion, of the defective product. Any and all costs of removal, installation, or re-installation, freight charges, and incidental or consequential damages are expressly excluded from this warranty. Items that are subject to wear are not considered defective when worn and are not covered.
• DYNATRAC components must be installed as a complete kit as shown in our current application guide. Any substitutions or exemptions of required components will immediately void the warranty. Some finish damage may happen to parts during shipping and is not covered under warranty.
• This warranty is expressly in lieu of all other warranties expressed or implied. This warranty shall not apply to any product that has been improperly installed, modified, or customized subject to accident, negligence, abuse, or misuse.
• 7392 Count Cir,
• Huntington Beach,
• CA 92647
• Phone: 714-596-4461
• www.dynatrac.com.
• 7392 Count Cir,
• Huntington Beach,
• CA 92647
• Phone: 714-596-4461

References

• Dynatrac - Confidence to Explore

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>