SDHQ-52-3005-200 2008-2021 Land Cruiser and LX 570 Billet Battery Hold Down Kit Installation Guide
- June 9, 2024
- SDHQ
Table of Contents
SDHQ-52-3005-200 2008-2021 Land Cruiser and LX 570 Billet Battery Hold Down
Kit Installation Guide
Product Packing List
Product: SDHQ-52-3005-200
Description: 2008-2021 Land Cruiser and LX 570 Billet
Battery Hold Down Upgrade
(1) SDHQ Main Tie Down
SDHQ-52-3005-200
Description: 2008-2021 Land Cruiser and LX 570 Billet Battery Hold Down
Upgrade
| (1) SDHQ Main Tie Dow | SDHQ-00-1810-U1-A |
|---|---|
| (1) SDHQ Tie Down Backer | SDHQ-52-3005-200-A |
| (1) Toyota 34R Battery Hold Down Upgrade | SDHQ-50-3005-U |
| (1) Hardware Package | SDHQ-52-3005-20 |
- (2) 5/16” – 18 x ¾” Grade 8 Hex Head Bolt
- (4) 5/16” Grade 8 Washers
- (2) 5/16” – 18 Grade 8 Locknuts
- (2) ¼” – 20 x 8” J-Hook
- (2) ¼” – 20 x 9” J-Hook
- (1) ¼” – 20 S.S. Serrated Flange Nut
- (1) Edge Clip Zip Tie
Included in SDHQ-50-3005-U1:
| (1) SDHQ Main Billet Battery Hold Do | SDHQ-50-3005-U1-A |
|---|---|
| (2) SDHQ Billet Aluminum Adapter | SDHQ-50-3005-U |
| (1) Hardware Pack | SDHQ-50-3005-U1-C |
INSTALLATION INSTRUCTION
Product: SDHQ-52-3005-200
Description: 2008-2021 Land Cruiser and LX 570 Billet
Battery Hold Down Upgrade
| Parts L | Hardware List | Required Too |
|---|
(1) SDHQ Main Tie Down SDHQ-00-1810-U1-A (1) SDHQ Tie Down Backer
SDHQ-52-3005-200-A (1) Toyota 34R Battery Hold Down SDHQ-50-3005-U1 (1)
Hardware Package SDHQ-52-3005-200-B| (2) 5/16” – 18 x ¾” Grade 8 Hex Head Bolt
(4) 5/16” Grade 8 Washers (2) 5/16” – 18 Grade 8 Locknuts (2) ¼” – 20 x 8”
J-Hooks (2) ¼” – 20 x 9” J-Hooks (1) ¼” – 20 S.S. Serrated Flange Nut (1) Edge
Clip Zip Tie| 5/16” drill or step bit Drill 10mm, 12mm, ½” Sockets Ratchet ½”
Wrench Sharpie Panel Clip Pliers
Tech Notes
ts: 2008-21 Toyota Land Cruiser Some drilling required. For use with 24, 27,
31, 34/34R and 25/35 Batteries. Replaces factory battery hold down. Approx.
Install Time: 1 Hour
Installation Instructions:
-
Unbox your SDHQ Battery Hold Down Upgrade kit and check over all parts and hardware. Familiarize yourself with them.
-
Preparing your Truck. In your truck’s engine bay, remove (7) push-in clips from the radiator cowl and remove the cowl. Next, remove the 12mm nuts on the rear J-Hook of the factory battery hold down and the 10mm bolt securing the front of the factory battery hold down. Remove the factory hold down. Disconnect your battery terminals and remove your battery. Locate the wiring harness in front of the battery and unclip it from the fender as shown below. Remove and discard the white fender clip and use the supplied Edge Clip Zip Tie to secure the wiring harness towards the headlight.
-
Drilling. Align the Main Tie down with the panel clip slot from Step 2 and parallel to the battery. Mark the other hole in the fender to be drilled. Remove the Main Tie Down. Drill a holethrough the mark and the slot. Deburr if necessary.
-
Place the Main Tie Down over the holes. Align (2) 5/16” bolts and washers through the Main Tie Down and drilled fender. Align the Tie Down Backer under the fender, over the bolts and secure the Main Tie Down with the remaining 5/16” hardware. See diagram below.
-
. Installing the SDHQ Battery Hold Down. Group 34/34R Batteries will use the 8” J-Hook, all others will use the 9” J-Hooks. Place the SDHQ Billet Aluminum Adapters through the SDHQ Battery Hold Down. Insert the J-Hooks through the Adapters and thread on the ¼” – 20 Flange Nuts onto the J-Hooks. Place the SDHQ Battery Hold Down on the battery. While tightening the ¼” nuts, hook the J-Hooks to the factory tie down and SDHQ Tie Down.
- Double check all hardware is installed correctly and tight***
- Re-torque ALL bolts after 100 miles***
190 S McQueen Rd
Ste 109 Gilbert, AZ 85233
Phone: 480-633-2929 | Fax:
480-633-1791
www.sdhqoffroad.com
Follow
For questions or help with the installation, please call SDHQ Offroad @ 480-633-2929 Mon.–Fri. 8:00am–5:30pm and Sat. 8:00am–3:30pm Arizona Time. www.sdhqoffroad.com Page 6 of 6
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>