TECHFROG YC-100 Alarm Clock Night Light Wireless Charger User Manual
- June 4, 2024
- TECHFROG
Table of Contents
TECHFROG YC-100 Alarm Clock Night Light Wireless Charger
Function Button
Function
-
Power Connection
- Plug the USB-A end of cable into the power adapter while plug Type-Send into the product.
- The product will be ready and stand by after all indicators are on.
-
Wireless Charging
- Output: 15w(max)
- Indicator display: Power connection successful-turn off after flashing blue light Standby- light off Charging- blue light on Charged- light off FOD-blue light flashes continuously
-
USB Charging
- Output: 5V-2A(max)
- Insert the USB cable into the corresponding USB socket on the back of the product. The device will prompt that it is charging,If there is no prompt, please check whether the cable is damaged.
(Note: Wireless charging and USB charging can charge at the same time)
-
Watch charging stand
Pull out the bracket from the alarm clock and install your own special charger for Apple Watch. Connect it to the USB port on the back to charge the device. (only supports Apple Watch) -
E. Alarm Clock Function
- Buttons: light on/off, mode, snooze, +,- button.
- Time Setting:
- Click the “mode” button once to set up the 12-hour time system and 24-hour time system, and adjust the value with+/- AM and PM will display while the 12-hour time system is set.
- Click the”‘mode” button twice to enter the hour setting, adjust the value with+/
- Click “mode” button third times after the hour setting, to enter minute setting, and adjust value with+/
- Click the “mode” button four times to finish the time setting.
Alarm Setting:
- Press “snooze” for 3 seconds to activate or deactivate the Alarm, Alarm indicator is on while the Alarm is activated.
- Click the “snooze” button once to enter the alarm hour setting, adjust the value with+/
- Click the “snooze” button twice after alarm hour setting, to enter alarm minute setting, adjust value with+/-
- Click the “snooze” button a third time to finish the alarm time setting.
- The alarm bell will ring for 5 minutes and will automatically turn off when there is no operation.
Sleepy Mode
After setting the alarm, there is a snooze function. When the alarm sounds,
the light of the ” snooze” button flashes. After clicking the ” snooze ”
button, the ringing will be delayed for 5 minutes. It can be set 3 times. Long
press the “snooze ” button for 3S to turn it off.
Night Light Setting:
- Night light has 7 colors (Red orange yellow green cyan blue purple)
- Press the ” light on/off ” button turn on the night light.
- Click the” light on/off” button to get other colors. Color change sequence: automatically Loop-red-orange-yellow-green-cyan- blue-purple.
- Press the ” light on/off ” 3 seconds button to turn the night light off.
The color description of the night light may differ from the product, please refer to the product.
ECO-power function:
- Button cell inside is only for timekeeping.
- When the power is off, the time memory function will be triggered.
As long as the time is set accurately before the power off, there is no need to reset the time after power on. All other functions are invalid after power off and will be restored after power on.
Note
- Attention: Please use DC 5V-3A or 9V-2A or 12V-1.5A or QC3.0 or QC4.0 or USB-PD charger to achieve the rated fast charging power, otherwise it willaffect the charging efficiency.
- Do not squeeze or collide
- Do not disassemble or put into the fire, water, to avoid short-circuit leakage.
- Do not use wireless chargers in severe high temperature, humidity or corrosive environments to avoid leakage of damaged circuits.
- Do not place too close to magnetic cards (ID cards, bank cards, etc) with magnetic strips or chips to avoid magnetic card failure.
- Keep more than 20cm between the implanted medical device (pacemaker, implantable cochlea, etc.) and the wireless charger to avoid potential disruption to medical devices.
- Keep the wireless charger and receiver device away from water and other liquids
- To clean the charger, make sure the power supply is disconnected.
- Usage temperature: 0-45°C.
- Usage humidity: 20-85%(40°C)
- The pictures in this manual are all illustrations. The final product is subject to fact.
- Inside package: alarm clock charger, charging cable, manual.
- the power adapter is not included. Please purchase otherwise or use the phone original adapter.
Specification
- Input: DC5V-3A, 9V-2A, 12V-1.5A
- Output power: 15W (max)
- Charging efficiency: 85%
- USB Output: 5V-2A(max)
- Size: 200x115x77mm
Applicable Equipment
Products qualified with Qi standard.
THANK YOU!
Thank you very much for purchasing TECHFROG products. If you find any problems
during use, please contact us via Amazon in time, We promise to reply within
12 working hours. Your valuable opinions and suggestions are the driving force
for our continuous improvement of products and services. The warranty period
of this product is 1 year from the date of purchase.
FCC STATEMENT
This device complies with part 15 of the FCC rules . Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This equipment
complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment.
NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- consult the dealer or an experienced radio/TV technician for help
- This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
Shenzhen Zhuoyou Technology Co., Ltd.
1st Floor, Building 16, Dawangshan Second Industrial Zone, Dawangshan
Community, Shajing Street, Baoan District, Shenzhen
FCC ID : 2A4KG-22TFAC100
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>