SWISSPHONE s.QUAD Voice 360 Tone/Voice Alerting Pager User Manual

User Manual
s.QUAD Voice 360

Introduction

Congratulations on your new Swissphone receiver! When you purchased the news.QUAD, you chose a top-range device. The s.QUAD delights with its optimum combination of user-friendly design, high carrying comfort, and top quality. It offers easy operation via four buttons and a graphical display. The s.QUAD can be a custom confi guard. For this reason, some of the functions described in this brief operating manual may be missing on your device. This brief operating manual provides important information that will help you get the most out of your device. Always keep this manual ready to hand. We wish you success in using the s.QUAD.

Getting started

Insert power source
The s.QUAD works with either a dry cell battery or a rechargeable battery. Insert the power source into the s.QUAD, make sure that you observe correct polarity. The s.QUAD will turn on automatically. A functional test is then performed. After the test, please specify whether you have inserted a dry cell battery or a rechargeable battery. The device is now ready for operation. Further information on the power supply can be found in the chapter ‘Charging the battery/power supply.
Turn on
To manually turn on the s.QUAD, you must press and hold one of the four buttons until the start screen or start text appears on the display. The home screen is visible after a few seconds and the s.QUAD is ready for operation.

Button function and navigation

BACK navigation button

• Scroll backward in the menu
• Change settings
• Display the start screen or start text

FORWARD navigation button

• Scroll forward in the menu
• Change settings
• Display the secondary menu by holding the button

OK confi rmation button / Volume

• Read messages
• Confi rm and acknowledge the alert
•  Confi rm menu selection
• Call up the last message received
• Change Volume, Scroll through the menu

ESC button

• Leave the current menu level
• Go to the home screen by holding the button

Open user menu
The ESC navigation button, allows you to switch from the home screen to the user menu. Press the FORWARD button to navigate to the next menu item, the BACK button to navigate back to the previous item. Or turn the scroll wheel to navigate the menu. To confi rm a selection you have made or a changed value, press the OK button. Each press of a button activates the backlight. By pressing the ‘OK’ button from the home screen, you can call up the last received message from the memory.

Back to the home screen
Press the ESC button to go to the next higher menu level. If you hold down the ESC button for two seconds, you return from the submenu to the home screen. If you do not dress any of the buttons for a pre-confi guard time interval, the s.QUAD automatically returns to the home screen.

Release key lock (if activated)

To release the key lock, press the two navigation buttons BACK and FORWARD simultaneously.
Start-up image/Start-up text
If you hold down the BACK navigation button on the home screen, the start-up image or start-up text appears.
Belt Mode
Belt Mode may be activated using the programming software. Once enabled, BACK and FORWARD get new functionality: Pressing FORWARD once will announce the current profi le and alert type. Pressing FORWARD repeatedly cycles through up to eight profi less. If you press and hold FORWARD, the secondary menu will be opened.
Pressing BACK will announce the current volume level. Repeatedly pressing BACK will decrease the volume until the alert type is silent. To increase volume, press and hold BACK until your desired Volume level is announced.
Secondary menu
If you hold down the FORWARD navigation button on the home screen for two seconds, you reach the secondary menu (only if confi figured in the menu). Functions that are seldom used can be placed on a second menu level (secondary menu) in order to declutter the main menu. When you leave the secondary menu, the device automatically returns to the start screen.

Display

The home screen is divided into fi ve sections:

1 st line: Status line
2nd line: Profi le
3rd line: Time, alarm clock
4th line: User line
5th line: Notifi cation line (unread messages, charger masks and so on)
Status line
The following symbols may be displayed in the status line:

Profi le display
This line indicates the currently selected profi le.
Time/alarm clock
This line shows the time. You can also see whether the alarm clock is activated.
Alarm clock Alarm clock function is activated

User line
A user-specifi c text is displayed.
Notifi cation line
This line shows the charger mask and the programming mask. If there are unread (unacknowledged) messages in the memory, the folder information is displayed.

Number of unread messages in message folder A
Number of unread messages in message folder B

Processing alerts/messages

Receive and read new messages
When your s.QUAD receives a message, an alert occurs through sound, vibration, and illumination of the OK button, followed by the voice announcement. By pressing the OK button, you can stop the alert. The header (timestamp) shows the message date, message time, and address name. If you now press the BACK navigation button, the header is displayed in full. A predefi ned ‘Fixtext’ may be displayed with each alert. In case a Hybrid-Alert including text was received, the message-text follows the fi xtext. The downward-pointing arrow indicates that there is more text.

You can use the OK button or the FORWARD navigation button to scroll to the end of the message. The message is marked as read as soon as you reach the end.

Listen to the announcement again
To listen to the announcement again, you simply need to press the OK button from the home screen. Playback of the announcement will begin automatically. Announcements can also be played directly from the message inbox, depending on the confi duration.
Message storage
The messages are stored in the message inbox or in the appropriate folder. They are stored chronologically in a list. Unread or protected messages are marked in the list. Unread messages are also indicated in the home screen.

Protect/delete messages
The ‘Protect message’ function allows you to protect a read message. To delete a message, select ‘Delete message’. The ‘Empty folder’ function lets you delete all messages in the list.

Lock messages or folders with a PIN
The ‘Lock message’ function allows you to lock a message. To be able to read a locked message, you must fi rest enter the corresponding PIN code. Similarly, you can use the ‘Lock folder’ function to protect an entire folder with a PIN code. You can also specify that messages in a folder should be automatically locked after a timeout. After this timeout, you will need to enter the corresponding PIN to be able to read these messages.
Alert reminder
If your device was confi figured to use an alert reminder, you will be reminded of unread messages after the preset time. The alert reminder is turned off as soon as you have read all messages.

Main menu

When you press the FORWARD navigation button, the device switches from the home screen to the main menu. You can use the FORWARD and BACK navigation buttons to navigate to the individual menu items. To open a selected menu item, press the OK button. To leave the main menu or to go to the next higher menu, press ‘ESC’.

Main menu

• Alerting
  See the chapter ‘Alerting’

• Switch off
  Switch off device
  

• Settings
  This menu contains various settings for the device (see the chapter ‘Settings’).
  

• Read last/ unread message
  The last message or all unread messages can be read at any time by pressing the OK confi rmation button.

• Messages
  Here you can manage the message folders (message inbox, folder A, folder B).

• Message inbox
  Manage or read messages
  (naming may differ)

• Folder A, B
  Manage or read messages in the message folders (naming may differ)

• Profi less
  Selection of one of the pre-programmed profi less

The menu can be freely confi guard using the programming software. Therefore, your menu on the device may differ considerably from the menu described here. Details regarding the programming of the various menu items can be found in the programming software manual.

Alert

You can select the following types of alerts in the ‘Alerting’ menu:

• Loud
  The alert pattern is played based on your programming.

• Quiet
  The alert pattern is played quietly.

• Ascending
  The alert pattern begins quietly and gradually gets louder.

• Discrete
  The alert is preceded by activation of the display backlight and vibration for ten seconds; the alert pattern is then played quietly (once).

• Silent
  To alert you, the display backlight and vibration are activated for ten seconds. The device is totally mute; furthermore, no key clicks are audible.

• Monitor
  The alert occurs as a Loud alert. Whenever radio communication is detected, it may be heard on the loudspeaker.

The following table shows the various types of alerts:

Loud
Quiet
Ascending
Discreet
Silent

Sound as defined  Quiet Medium volume
Vibration

Priority messages are signaled at the end always with the programmed volume.
s.QUAD in the charger:

• Vibration is not activated.
• The alert type can be overridden using the charger mask.

Warning: Do not hold the device next to your ear. The alarm tones are very loud and can damage your ears!

Settings

The menu items under Settings depend very much on the confi duration of the s.QUAD.
Rotate display
Rotate the display for easier handling, e.g. for left-handed people.
Battery Confi rmation tone
Selection of the inserted power source You can turn on or off the confi rmation tone that is played when a change is applied.
Bluetooth
Settings for the Bluetooth 4.0 interface (Low Energy)
Date and time
You enter the date/time by repeatedly pressing the FORWARD and BACK navigation buttons. If the correct number is shown, press the OK button to
confi rm.
Detailed status
– State display of the inserted power source
– Five-level display of the signal strength at the current location
Last signal: signal strength of the last transmission in the network
Last message: signal strength of the last received message

Display of signal strength (RSSI)
……No signal present (no reception)
Best signal strength
– Bluetooth connection status
– Device information (serial number and current fi firmware)

Backlight
You can turn the automatic backlight on or off.
ECO mode
Active ECO mode prolongs battery life.
Out of range alarm,
You can turn the acoustic warning of the out-of-range alarm on or off.
Contrast
You can set the display contrast between One (light) and Eight (dark).
Message font
Select one of the various fonts for the message text.
Melodies
Select the address. After pressing the OK button to confi rm, you can use the FORWARD or BACK navigation button to change the alert melody.
Alert reminder
Select the type of alert reminder: fl ashing and/or periodic beeping. Language You can select the menu language.
Key lock
You can turn automatic activation of the key lock on or off.
Key click
You can turn the key click on or off.
Key vibration
A short vibration can be used to signal that the end of a menu has been reached. You can turn this function on or off.
Alarm clock
You can set the alarm time and activate or deactivate the alarm clock.
Vibration
You can activate or deactivate vibration.

Profiless

Select the ‘Profi les’ menu. The s.QUAD has two types of profi le: select profiles and toggle profiles. Whilst only one of the select profiles can be activated at any one time, multiple toggle profiles can be simultaneously active. You can turn the toggle profiles on or off, irrespective of other profiles. You can switch over the select profiles using the radio buttons. To turn the toggle profiles on or off, use the checkboxes

Power-on PIN lock

If the Power-on PIN lock is confi guard in your s.QUAD, you will be prompted to enter the PIN code when starting the device for the first time. Use the FORWARD and BACK navigation buttons to select the individual numbers of the PIN code. Confi rm the numbers by pressing the OK button. If you enter an incorrect PIN code ten times in succession, the device will be locked. In this case, the only way to unlock it is by using the programming software.

Alarm clock

Set alarm clock

Select the ‘Alarm clock’ menu. Use the FORWARD and BACK navigation buttons to turn the alarm clock on or off. You can also use the FORWARD and BACK navigation buttons to set the alarm time. Press the OK button toconfi rm. The activated alarm clock function is displayed with the corresponding symbol on the home screen.

Acknowledge alarm
When the alarm clock sounds, the following selection appears: Snooze or Stop. Selecting ‘Stop’ will end the current alarm call. However, the alarm clock remains activated and will wake you on the next day. Selecting ‘Snooze’ will initially turn off the alarm sound. However, it will sound again after fi ve minutes.

The s.QUAD turns on with the alarm call
If the alarm clock is turned on and the s.QUAD is turned off, the s.QUAD will turn on at the alarm time and the alarm clock sounds.

Connection to an external device (for example, smartphone)

The s.QUAD has a Bluetooth 4.0 Low Energy interface that can be used to communicate with a remote terminal (smartphone). You can turn the interface on or off using the
menu. If the interface is turned off, then the s.QUAD cannot be accessed via Bluetooth. The status of the Bluetooth interface is shown using a symbol in the status line.
Connection setup
As soon as the Bluetooth interface is turned on on the s.QUAD, a connection with the remote terminal (smartphone) is set up (advertising). The s.QUAD is visible on the remote terminal (smartphone) as soon as advertising has been successful.
Pairing
During advertising, the s.QUAD transmits an identifying name (s.QUAD and serial number) via the Bluetooth interface. You can now select the relevant s.QUAD on the remote terminal (smartphone). To prevent an inadvertent or unauthorized connection, a six-digit number (passkey) is displayed on the s.QUAD during connection setup and you must enter it on the remote terminal (smartphone).
The s.QUAD remembers the connection with the remote terminal. This applies even after the battery has been replaced. If the device wishes to connect with the s.QUAD again, the connection is established automatically. As long as the connection remains active, the s.QUAD will not be visible to other remote terminals (smartphones). Terminating a connection
If you would like to connect the s.QUAD with another remote terminal (smartphone), you must first delete the active connection.

Charging the battery/power supply

During the charging process, the LED of the charger glows orange. A full charge takes approximately four hours. At the end of the charging process, the color of the LED changes to green. The charge state and the name of the charging profi le are shown on the s.QUAD display. The two charging profi less define the alert in a single device charger and in the multi-device charger.

Power source
You can use the following AA or LR6, AM3, or Mignon batteries as a power source:

• Dry cell: leak-proof alkaline dry cell battery
• Rechargeable battery: nickel-metal hydride rechargeable battery

Important:

• Alkaline batteries must not be charged. There is a risk of explosion!
• For safety reasons, only use original chargers from the accessory product range of Swissphone Wireless AG.
• Never expose dry cell batteries or rechargeable batteries to open fl games. There is a risk of explosion!

Miscellaneous

Further information on this product and other products of Swiss- phone Wireless AG can be found at:
http://www.swissphone.com

Safety notices

• This product must not be used in explosive environments.
• The device must not be opened.
• Keep out of reach of children.
• Liability disclaimer
  Swissphone Wireless AG gives no guarantee and accepts no liability in connection with the content of this document. The company reserves the right to make changes to the content of the s.QUAD Operating Manual.

Technical Data

Manufacturer
Swissphone Wireless AG
Fälmisstrasse 21
CH-8833 Samstagern

Hereby, Swissphone Wireless AG declares that the radio equipment type DE12A is in compliance with Directive
2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: https://www.swissphone.com

05/2021 0343198 v2

Documents / Resources

| SWISSPHONE s.QUAD Voice 360 Tone/Voice Alerting Pager [pdf] User Manual
s.QUAD Voice 360, Tone Voice Alerting Pager, s.QUAD Voice 360 Tone Voice Alerting Pager
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>