TOPPING L30II Headphone Amplifier User Manual
- June 9, 2024
- TOPPING
Table of Contents
TOPPING L30II Headphone Amplifier
Introduction
Thank you for purchasing linear headphone amplifier L30 II! L30 II is a high- performance linear headphone amplifier that supports RCA input and output, equipped with a 6.35mm headphone jack and gain selections function. Now we recommend first to read this manual for you to correctly use all the functions of L30 II.
Content List
- L30 II: X 1
- AC adapter: X 1
- 6.35 mm to 3.5 mm adaptor: X 1
- User manual: X 1
- Warranty card: X 1
Note: You can download the user manual on http://www.topping.audio/
Description
-
(DOutput switch
Switch to PRE output( RCAoutpul) or HPAoutput (Headphone output), or turn off. -
Gain switch
H / M / L respectively corresponds to 16.5dB / 0dB / -14dB -
Power indicator
The light will be always on when the L30 II is turning on, and goes off when ii is turning off, blinks to indicate une xpected output. -
6.35mm headphone output jack
Suitable for headphones with 6.35mm jack -
Volume knob
Used to adjust the volume. It is recommended to turn down the volume before playing music. -
Righi channel single-ended RCA input
-
Left channel single-ended RCA input
-
Right channel single-ended RCA output
-
Left channel single-ended RCA output
-
Power input
AC15V/1 A50Hz/60Hz
Product specifications
10.0cm x 13.5cm x3.2cm | |
---|---|
360g | |
Power | 15VAC/1A 50Hz/60Hz @DC base 5.5*2.5 |
Gain | L/MIH |
Amplifier input | 1 x RCA (L+R) |
Headphone Amp output | 1 x 6.35mm headphone output jack |
Line out output | 1 x RCA (L+R) |
Indicator light | White |
L30 II Headphone Amplifier specifications
L30 II Headphone Amplifier specifications
THD+N @1kHz (A-wt)
| <0.00006% @Output=500mW (320)
<0.00005% @Output=80mW (3000)
THD @20-20kHz 90kBW
| <0.00008% @Output=500mW (320)
<0.00007% @Output=80mW (3000)
SNR @MAX OUT 1kHz (A-wt)| 144dB
Dynamic Range @1kHz (A-wt)| 144dB
Frequency Response| 20Hz-40kHz (±0.05dB)
Output Level
| 14Vpp@G=L
31Vpp @G=M
37Vpp@G=H
AP measured noise level (A-wt)
| <0.7uVrms@G=L
<0.7uVrms@G=M
<1.5uVrms @G=H
Actual noise level* (A-wt)
| <0.3uVrms @G=L
<0.3uVrms @G=M
<1.4uVrms @G=H
Channel Crosstalk @1kHz| -92dB
Input sensitivity
| 25Vrms @G=L
11.2Vrms @G=M
2.0Vrms @G=H
Gain
| -14.0dB @G=L
OdB @G=M
16.5dB @G=H
Output Impedance| < 0.10
Output Power
| 3500mW x 2@160 THD+N<0.1%
2700mW x 2 @320 THD+N<0.1%
2000mW x 2 @640 THD+N<0.1%
560mW x 2 @3000 THD+N<0.1%
Load Impedance| >80
Note:
- The above data is the result of the test in TOPPING laboratory under AC2 20V 50Hz condition.
- The actual noise level is obtained by boosting the noise of L30 II by 40dB using a low noise amplifier in front of the APx555B then dividing the measured noise by 100 times.
L30 II Pre-amplifier specifications
THD+N @1kHz (A-wt)| <0.00006%
THD @20-20kHz 90kBW| <0.00007%
SNR @MAX OUT 1kHz (A-wt)| 144dB
Dynamic Range @1kHz (A-wt)| 144dB
Frequency Response| 20Hz-40kHz (±0.05dB)
Output Level
| 14Vpp@G=L
31Vpp@G=M
37Vpp @G=H
AP measured noise level (A-wt)
| <0.7uVrms@G=L
<0.7uVrms @G=M
<1.SuVrms @G=H
Actual noise level* (A-wt)
| <0.3uVrms @G=L
<0.3uVrms @G=M
<1.4uVrms @G=H
Channel Crosstalk @1kHz| -92dB
Input sensitivity
| 25Vrms @G=L
11.2Vrms @G=M
2.0Vrms @G=H
Gain
| -14.0dB @G=L
OdB @G=M
16.5dB @G=H
Output Impedance| 200
Note:
- The above data is the result of the test in TOPPING laboratory under AC2 20V 50Hz condition.
- The actual noise level is obtained by boosting the noise of L30 II by 40dB using a low noise amplifier in front of the APx555B then dividing the measured noise by 100 times.
Precautions for daily use
- The output jacks shall not be grounded or short-circuited
- Do not keep the unit in a hot, humid environment or hit the unit strongly.
- Opening the case instantly voids the warranty!
- Indoor use only.
- Topping accepts no liability for any loss or damage arising directly or indirectly from the failure of L30 II.