savio FAN-01 ARGB Fan Kit User Manual

savio FAN-01 ARGB Fan Kit

Thank you for choosing Savio product!

• If our product meets your expectations, share your opinion with other people on the portal ceneo.pl, social media or on the website of the store where you made the purchase. If you want to show our device on SAVIO Facebook Page, we will be very pleased.
• If there is something that we could improve on our products, please write to us at support@savio.net.pl

Thanks to your feedback, we will be able to better adapt the product to your expectations.
Before starting the use of purchased device it is recommended to read the whole manual.

Technical specification of the fans

• Fan size: 120 mm
• Voltage: 12 V
• Power connector: SATA
• Fan connector: 6-pin
• Backlight: ARGB
• Speed control: yes, with the remote control
• Max. rotation speed: 1200 RPM
• Max. noise level: 25 dBA

Controller technical specification

• 10 × 6-pin connector
• 2 × 3-pin connector
• 1 × 4-pin power connector
• 1 × Aurora 2-pin connector
• 1 × RS 2-pin connector
• Frequency bands in which the radio equipment operates: 433.920 MHz
• Maximum radio-frequency power transmitted in the frequency band in which the radio equipment operates: 5 dBm

Kit Contents

• 4 × ARGB fan
• Controller
• Remote control
• 16 × screws for mounting the fan

Assembly

• Mount the fans in a chosen place inside the PC case, securing them with the screws included in the kit.
• Stick the controller on the metal part of the case behind the motherboard (outer side).
• Connect the fans to the 6-pin sockets on the controller.
• Select one of the three available fan control options, the connection scheme to the controller is shown in picture 1.

Fans backlit control

The controller enables several variants of controlling the fans.

• Backlit control by motherboard:
  If the motherboard has ARGB (5V) or VDG (Gigabyte motherboard) socket, the backlit can be controlled by using a dedicated motherboard software.

• Connect the power supply directly to the controller.

• Connect ARGB (5V) or VGD cable to motherboard. CAUTION!
  During controlling by motherboard the remote control will not work.

• Backlit control by manual mode using the RESTART button or the LED on the PC case.
  If the motherboard does not have an ARGB (5V) or VDG (Gigabyte motherboard) connector, the backlit can be controlled using the RESTART or LED button (if the computer case has a dedicated but-ton) located on the top of the housing.

• Connect power directly to the controller.

• Connect the LED SW/RESET SW cable to the controller.

Backlit control by remote control.

The backlit can be also controlled by remote control, which is in-cluded to case set. The remote control works on radio wave, by that solution, backlit colour and working parameters of fans can be changed from far distance. For the correct work of remote control you need to select manual mode.
To be able to control by remote control you need to:

• Connect the power supply to the controller.

Backlit selection control modes.

If the controller is connected at the same time to the motherboard and RESTART/LED button, only one mode of backlit control will work properly.
To change backlit mode control you need to:

• Press the RESTART/LED button placed on the top part of case  for about 2 sec.
• Press and hold for 3 sec  the  button placed on the remote  control. Two above sequences will cause change mode from the motherboard to manual by RESTART/LED button and vice versa.

Remote control

• Turn on the backlit
• Automatic backlit mode
• • Turn off the backlit
• fan speed
• Select the next backlit mode
• Increase animation speed
• Reducing fan speed
• Select the previous backlight mode
• Reduct animation speed
• Change backlit to red
• Change backlit to green
• Change backlit to blue
• Change backlit to orange
• Change backlit to azure
• Change backlit to purple
• Change backlit to yellow
• Change backlit to turquoise
• Change backlit to pink
• Control backlit by voice, mode 1
• Control backlit by voice, mode 2
• Change of backlit modes
• Control backlit by voice, mode 3

Safety conditions

• Use the product in accordance with its intended use, as improper use may damage the product.
• Do not expose the device to moisture, heat or sunlight, do not use the product in a dusty environment.
• The device should be cleaned only with a dry cloth.
• Independent repairs and modification result automatic loss of the warranty.
• Hitting or dropping may damage the product.

Warranty:

The warranty covers a period of 24 months. Independent repairs and modifications result in automatic loss of the warranty. Warranty card is available for download on our website: www.savio.net.pl/en/service

Information for customers and contractors and communication re-garding complaints:
Pursuant to Article 13 section 1 and 2 of the General Data Protection Regulation (EU) 2016 / 679 of the European Parliament and of the Council of 27 April 2016 (hereinafter referred to as GDPR), please be advised that Elmak Sp. z o.o., with its registered seat at ul. Morgowa 81; 35-323 Rzeszów becomes the Administrator of your personal data. The Specialist for General Data Protection (SODO) can be contacted in writing to: SODO, Elmak Sp. z o.o., ul. Morgowa 81; 35-323 Rzeszów, via e-mail address: sodo@elmak.pl, and by phone at +48 (17) 854 98 14. Your personal data will be processed in order to perform the contract, in accordance with Article 6(1)(b) of the aforementioned regulation, to the extent resulting from tax laws and financial regulations. Recipients of your personal data include entities authorized by legal regulations to obtain personal data as well as processing entities providing services to Elmak Sp. z o.o. Your personal data will be stored on the basis of Administrator’s legitimate interest. You have the right to access your data, and the right to rectify, delete or limit processing of your data. You have the right to lodge a complaint to the supervisory body if you believe that the processing violates the GDPR. The provision of personal data is voluntary, however, a failure to provide such data may result in a refusal to conclude or in termination of a contract. Your personal data will not be subjected to automated decision making, including profiling referred to in Article 22 section 1 and 4 of the GDPR of April 27, 2016.

Information of the utilization of electrical and electronic equipment
This symbol indicates that electrical appliances should not be dis carded with other household waste. Used equipment should be handed over to a local collection point for this type of waste or to a recycling center. Please contact your local authorities for information about dis-posal methods available in your area. Waste electrical equipment may contain hazardous substances (e.g. mercury, lead, cadmium, chromium, phthaltes) which can get into air, soil and groundwater when leaking from used appliances. Environmental pollution with these substances leads to their bioaccumulation, causing lesion of disease in living or-ganisms, which would pose a risk to human and animal health or life. Households may contribute to environmental protecion by proper waste collection. In such way, hazardous substances from the equipment are neutralized and valuable secondary raw materials are reused for production of new equipment.

Controller connection scheme

References

• Strona główna - Savio
• Strona główna - Savio

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>