BRISTAN PM2 SHCDIV BLK Thermostatic Recessed Dual Control Valve User Guide

: June 9, 2024
: BRISTAN

BRISTAN PM2 SHCDIV BLK Thermostatic Recessed Dual Control Valve

BRISTAN PM2 SHCDIV BLK Thermostatic Recessed Dual Control
Valve

Specifications

Dynamic Water Pressure

Min : 0.2 bar
Max : 5.0 bar
Maximum Static Pressure: 10.0 bar

Inlet Water Temperature

**Cold Water Supply

Min: 5°C Max: 25°C
**

**Hot Water Supply

** 65°C Recommended

IMPORTANT
The inlet hot water must be at least 10°C above the required blend temperature.

Inlet Dimensions

Inlet Connections

Tools You’ll Need

Socket Spanner
Tools You’ll Need

|

Flat head
Screwdriver

|

Drill

|

Adjustable Spanner

---|---|---|---

Pipe Cutter

|

Silicon Sealant

|

Hexagonal Keys

|

Pipe & Wire Detector

Prior to Installation

All products manufactured and supplied by Bristan are safe to use provided that they are installed, operated and receive regular maintenance in accordance with these instructions

This product needs to be installed in accordance with, and meet the requirements of the Water Supply (Water Fittings) Regulations 1999 and current by-laws. For full Installation Requirements & Notes (IRN) please visit wras.co.uk/directory

Isolation valves must be fitted to the inlet water supplies to ensure ease of future maintenance. Before installing this product the water supply must be thoroughly flushed in order to remove any swarf, solder etc. Full access must be made available for future maintenance/ servicing purposes.

Before drilling into walls, check that there are no hidden electrical wires, cables or water supply pipes. This can be checked with the aid of an electronic detector.

If power tools are used do not forget to:
– Wear eye protection
– Unplug equipment after use

This product must not be modified in any way as this will invalidate the guarantee.
If in doubt, contact a registered plumber, your Local Water Authority or the Secretary of the Institute of Plumbing, address as follows:-
The Institute of Plumbing,
64 Station Lane,
Hornchurch,
Essex,
RM12 6NB, Tel: 01708 472791

Cavity Dimensions (mm)

Minimum Fitting Depth : 50mm
Maximum Fitting Depth : 75mm
Concealing Plate Adjustment Range : 25mm

$Cavity Dimensions $mm$$

Pack Contents

Valve Configuration

Remove the inlet elbows and filters. Remove the plastic inserts from the valve inlets and insert the flow regulators. Replace the elbows, ensuring the filters are fitted.
Screw the shrouds onto the valve.

Installation

Install suitable batons (if required) into the cavity. Take the finished wall surface into consideration when fitting the valve into the cavity. Mark the position of the valve; drill and plug holes to suit.
Secure the valve using the screws supplied (solid walls only) or a suitable alternative.
Connect the inlet pipes ensuring the olives are fitted.
Plumb your chosen outlets into the valve.
Turn on the water supply and check the valve for any leaks
Draw around the concealing plate as a template, measuring in by 10mm to give clearance. Finish the wall surface. Using a silicon sealant, push on the concealing plate and hold firmly until set.
Fit the handles.

Temperature Adjustment

Turn the handle to the maximum temperature setting, then remove it.
Turn the spindle to increase or decrease the temperature. Check the temperature and adjust until you achieve the desired result.
Fit the temperature handle back in the maximum hot position.

General Cleaning

Bristan products are made from premium materials, with hand polished, PVD, EPD or electroplated finishes.
Your shower should be regularly cleaned with warm water, a mild pH-neutral liquid soap, and polished with a soft cloth. Any residues from soap, toothpaste, shampoos and shower gels can cause blemishes if not rinsed off straight after use.
Household bleaches and cleaners contain harsh chemicals and may damage the surface finish. Avoid using abrasive cloths, scouring pads, scrub sponges, steel wool or anything similar.