LANCOM GS-3152XP Fully Managed Access Switches User Guide

**LANCOM GS-3152XP Fully Managed Access Switches User Guide

**

Mounting & connecting

Hardware Quick Reference

LANCOM GS-3152XP

1. Configuration interface (Console)
   Connect the configuration interface via the included serial configuration cable to the serial interface of the device you want to use for configuring / monitoring the switch

2. TP Ethernet interfaces Use Ethernet cables to connect the interfaces 1 to 48 to your PC or a LAN switch.
   

3. SFP+ interfaces Insert suitable LANCOM SFP modules into the SFP+
   interfaces 49 to 52. Choose cables which are compatible with the SFP modules and connect them as described in the module’s documentation.

4. Power connector (device back side) Supply power to the device via the power connector. Please use the IEC power cable supplied or a countryspecific LANCOM Power Cord.

5. ATTENTION: High touch current possible! Connect to earth before connecting the power supply
   

Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!

Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.

The power plug of the device must be freely accessible.

Please observe the following when setting up the device

• The power plug of the device must be freely accessible.
• For devices to be operated on the desktop, please attach the adhesive rubber footpads
• Do not rest any objects on top of the device
• Keep all ventilation slots on the side of the device clear of obstruction
• Mount the device into a 19” unit in a server cabinet using the provided screws and mounting brackets.
• Please note that support service for third-party accessories is excluded.

1. System / Link/Act/Speed / PoE-LED
   System: off Device powered off
   System: green Device operational
   System: red Hardware error
   Link/Act/Speed: Link/Act/Speed:  Port LEDs show link / activity / port
   speed status
   PoE: green Port LEDs show PoE status

2. Mode/Reset button
   Short press Switching the port LED display
   Pressed until all port LEDs are off:Device restart
   Pressed until all port LEDs glow permanently:Configuration reset and device restart

3. TP Ethernet ports
   ff Port inactive or disabled
   Green Link 1000 Mbps
   Green, blinking Data transfer, link 1000 Mbps
   Orange Link ≤ 100 Mbps
   Orange, blinking Data transfer, link ≤ 100 Mbps
   

4. 10 G SFP+ ports
   Off Port inactive or disabled
   Blue Link 10 Gbps
   Blue, blinking Data transfer, link 10 Gbps
   Green Link 1 Gbps
   Green, blinking Data transfer, link 1 GbpsO
   

Hardware

Power supply: Internal power supply unit (110–230 V, 50–60 Hz, max. 1 A), PoE based on IEEE 802.3af and IEEE 802.3at

Power consumption Max. 850 W

Environment: Temperature range 0–40° C; short term temperature conditions 0-50°C; humidity 10–90%; non-condensing

Housing: Robust metal housing, 1 HU with removable mounting brackets for 19“ installation, network connectors on the front, 442 x 44 x 375 mm (W x H x D)

Number of fans: 1

Interfaces

ETH: 48 TP Ethernet ports 10 / 100 / 1000 Mbps
SFP+:4 SFP+ ports 1 / 10 Gbps 52 concurrent ports in total

Package Content

Mounting brackets: Two 19” brackets for rack mounting;If an additional rear support surface is required for more stable mounting of the switch, please use the LANCOM Switch Rack Mount L250, item no.: 61432, which is available as an accessory

Cable : IEC power cord 230 V, serial configuration cable 1.5 m

This product contains separate open-source software components which are subject to their own licenses, in particular the General Public License (GPL). The license information for the device firmware (LCOS) is available on the device‘s WEBconfig interface under “Extras > License information“. If the respective license demands, the source files for the corresponding software components will be made available on a download server upon request.

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>