NiteDevil IPCND714 24C Camera Instruction Manual

NiteDevil IPCND714 24C Camera

Introduction – NiteDevil Hero

The NiteDevil Hero can stay in full colour around the clock using its built in white light LEDs to produce superb full colour images.

Up to 25m IR range (true day/night filter) and up to 20m white light range, 4MP resolution, built in PoE, H265 and H264 codec. With built in dual IR and white light you can choose how the camera best works in your install. Using white light to give visual warning or using IR illumination to get a more discreet set up.
This model also features blue and red deterrence LED as an option which can warn off intruders, similar to law enforcement strobe lights. *Adjustable with compatible NVR / DVR Firmware.
A built in microphone means you can see and hear what’s happening, recording the audio & video on your NVR for the best possible CCTV evidence.
Dual PoE and 12V means you can power and connect the camera to POE NVRs in seconds using one simple CAT5/6 cable for video, power and audio. If your system doesn’t support PoE use the 12V input or a PoE injector such as our POE200.

Key Features

• Full Colour 24/7
• Sees in Low Light
• NiteDevil® Tech
• 4MP
• Stunning Images
• ONVIF
• White or Grey Case
• IP66 In & Outdoor
• Dual PoE/12V
• Dual IR & White Light
• Red & Blue Strobe Deterrence
• Wide-Angle 2.8mm
• Built-in Mic
• Metal Case
• Motion Detect
• Picture Flip

Essential Tools and ZipFinder

To install this product you will need:

• Laptop / Windows PC
• Screwdriver
• Drill
• ZIP NVR or DVR
• PoE Switch / 12V DC power supply
• Ethernet CAT5/5e/6 Cable

ZipFinder – IP Camera Configuration Tool
ZipFinder is a Windows PC software for discovering and configuring IP cameras a network.
Use ZipFinder on non-PoE installs, to help problem solving issues such as forgotten or unknown
IP Addresses.
To download visit ZipNVR.com

Connections

Powering the camera
Option 1 – Power the camera from 12V DC (via the 2.1mm DC Socket), the current consumption is 420mA.
The camera is polarity sensitive so connections must be correctly made.
Option 2 – Power the camera using a PoE 48V RJ45 Socket
When connecting ZIP PoE NVR plug the camera directly into the NVRs built in PoE switch.
The camera should automatically become visible after being connected for approximately 1 minute.

Mounting

SD Card

The SD Card can be found on the rear of the eyeball, a small gasket will need to be removed to install the SD card.
For local recording on the camera itself an SD card must be installed.
Recording time will vary dependent upon: SD card size and encoding settings
32GB SD Card 31 hours
64GB SD Card 62 hours
128GB SD Card (MAX) 124 hours
The camera can be set to only record when triggered via motion detection, alarm input or AI smart, this maximises the recording time achievable.
Remove power from the camera when inserting / removing the SD card.

Setup Options

PoE ZIP NVR
When connecting to a ZIP PoE NVR plug the camera directly into the NVR’s built in PoE switch.
The camera should automatically become visible after being connected for approximately 1 minute.
The 100m distance for a camera can be increased when the PoE Mode is set to EPoE.
In the menu on a ZIP PoE NVR go to:-
Video > IP Channels > PoE Mode

Non-PoE ZIP NVR
When connecting cameras to a Non-PoE NVR, they are first connected to an external network switch which is in-turn connected to the NVR as shown below.

See Extra Resources for more information on Adding IP Cameras manually to a ZIP Recorder.

How to Login via Browser

The AI smart features can be configured in a ZIP recorder or directly in the browser interface of the camera (standalone)
Only one smart detection feature can be enabled at any given time.
See the NVR or DVR manual for information on configuring these features with a ZIP recorder.
Follow the steps below for configuring the settings directly in the camera via a browser for standalone setup.
You will need…

• Windows Based PC/ Laptop connected to router/ PoE switch
• ZipVision Pro App on Mobile Device
• PoE Switch connected to Network/ Router
• Ethernet network cable
• ZipFinder software, available via this link below:-
  www.softcctv.com/store/Item/Zip-Finder-IP-CCTV-Security-Camera-Discovery- Tool
  NOTE If the PC being used is on a different IP range to the PC then add the IP range of the camera to the PC using the below guide:-
  https://softcctv.com/helpdesk/kb/faq.php?id=571

1. Plug the camera’s RJ45 port with a network cable into a PoE switch

2. Using ZipFinder on a Windows Based PC/ Laptop Search and then tick the camera

3. Select Net Mode = DCHP, then click Modify

4. Search again, to get the updated IP address.

5. Select the IP address of the camera, Internet Explorer will pop-up, and ask to download and install the plug-in.

6.  Download, install and follow the steps for the plug-in installation, then re-load the browser by selecting the IP address again.

Login to the IP Camera, the default login details are:

Browser Menu Settings

IPCND714
The menu be configured directly in the browser interface of the camera (standalone), in Remote Setting you will find the menu settings below:

YYYY/MM/DD

Time Format| 24 Hour / 12 Hour
Flicker Control| 50Hz / 60Hz
Show Name| Enable / Disable
Show Time| Enable / Disable
Save / Refresh
Image Control| Image Setting| Full Colour Mode / Day/Night Mode / Schedule
Mode| Manual / Automatic mode / Schedule / OFF
Angle Trad| 180 / 0
Mirror| Disable / Vertical / Horizontal / All
Backlight| DWDR / HLC / BLC / Disable
White Balance| Automatic mode / Manual
Shutter| Automatic mode / Manual
Time Exposure| 1/5 to 1/200000 / Flickerless
3D Noise Reduction| OFF / Automatic Mode / Manual
Save / Default / Refresh
Privacy Mask| Enable / Disable
Record| Encode| Mainstream| Resolution| 2560 x1440
FPS| 1 -25
Video Code Type| H.265 / H.264
Video Code Level| Main Profile
Bitrate Control| CBR / VBR
Bitrate Mode| Predefined / User-Defined
Bitrate| 512 to 4096
I Frame Interval| 1 to 100
Audio| Enable / Disable
Save / Refresh
Substream| Resolution| 640 x 480
FPS| 1 -25
Video Code Type| H.265 / H.264
Video Code Level| Main Profile / Baseline / High Profile
Bitrate Control| CBR / VBR
Bitrate Mode| Predefined / User-Defined
Bitrate| 128 to 1024
 |  |  | I Frame Interval| 1 to 100
---|---|---|---|---
Audio| Enable / Disable
Save / Refresh
Record| Record| Stream Mode| Mainstream / Substream
Record| Enable / Disable
PreRecord| Enable / Disable
Netbreak| Enable / Disable
Save / Refresh
Schedule| User Definable
Save / Refresh
Event| Setup| Motion| Enable| Enable / Disable
Sensitivity| 1 to 8
Smart motion

detection

| Enable / Disable
Save / Refresh
Deterrence| Warning Light| Enable / Disable
Warning Light Duration| 5 to 180
Save / Default / Refresh
Siren| Siren| Enable / Disable
Siren Type| Alarm1
Siren Level| 1 to 10
Siren Duration| 5 to 180
Save / Refresh
Sound Detection| Enable| Enable / Disable
Rise| Enable / Disable
Rise Sensitivity| 1 to 100
Sound Intensity| 1 to 100
Decline| Enable / Disable
Decline Sensitivity| 1 to 100
Save / Schedule / Refresh
Alarm| Motion| Post Recording| OFF / 5s / 10s / 20s / 30s
Send Email| Enable / Disable
FTP Picture Upload| Enable / Disable
Enable Record| Enable / Disable
Deterrent| Enable / Disable
Save / Schedule / Refresh|
Sound Detection| Post Recording|
Send Email|
Enable Record|
Save / Schedule / Refresh
AI| Setup| PID| Enable| Enable / Disable
Sensitivity| 1 to 4
Detection Type| Pedestrian & Vehicle / Person / Vehicle
 |  |  | Rule Number| 1 to 4
---|---|---|---|---
Rule Enable| Enable / Disable
Rule Type| /           /              B
Save / Refresh
LCD| Enable| Enable / Disable
Sensitivity| 1 to 4
Dynamic Marking| Enable / Disable
Detection Type| Pedestrian & Vehicle / Person / Vehicle
Rule Number| 1 to 4
Rule Enable| Enable / Disable
Rule Type| /           /              B
Save / Refresh
Alarm| PID / LCD| Post Recording| OFF / 5s / 10s / 20s / 30s
Send Email| Enable / Disable
FTP Picture Upload| Enable / Disable
Enable Record| Enable / Disable
Deterrent| Enable / Disable
Save / Schedule / Refresh
Network| General| General| DCHP| Enable / Disable
IP Address| User-definable
Subnet Mask| User-definable
Gateway| User-definable
DNS1| User-definable
DNS2| User-definable
Video Encryption Transmission| Enable / Disable
Save / Refresh
Port Configuration| HTTP Port| Enable / Disable| User-definable
Client Port
HTTPS Port
RTSP Port
Muticast Port| 1024 – 65535
P2P Enable| Enable / Disable
Save / Refresh
Email| Email| Enable / Disable
Encryption| OFF / SSL / TLS / Automatic mode
SMTP Port| 1 – 65535
SMTP Server| User-definable
Username
Password
Sender
Receiver 1
Receiver 2
Receiver 3
Interval
 |  |  | Save / Test/ Refresh
---|---|---|---
RTSP| RTSP Enable|
Anonymous Login| Enable / Disable
Instruction: rtsp://IP:RtspPort/ch01/A

A: 0(main stream), 1(sub stream), 2(mobile stream)

Save / Refresh
DDNS| DDNS| Enable / Disable
Server| NO_IP / DYNDNS
Hostname| User-definable
Username| User-definable
Password| User-definable
HTTPS| Certificate Type| Default/ Custom
Save / Refresh
Storage| Disk| Select Disk
Overwrite| OFF / Auto
Save / Format Hard Disk / Refresh
Audio| Enable Audio| Enable / Disable
Output Volume| 0 – 8
Input Volume| 0 – 8
Audio Code

Type

| G711A / G711U
Save / Refresh
System| General| Date and Time| Time Setting mode| Static / NTP server synchronization
Date Format| Day/Month/Year

Year-Month-Day Month/Day/Year

Time Zone| GMT -12:00 to GMT + 13:00
Time Format| 24Hour / 12 Hour
System Time| User-definable
Server Address| Time.windows.com / time.nist.gov / pool.ntp.org / Define User
Save / Synchronize computer time / Refresh
Daylight Saving Time| Daylight saving time| Enable / Disable| Set by week /

set by date

Start Time| User-definable
End Time| User-definable
Time Offset| 1Hour / 2 hours
Save / Refresh
Multi-User| Customize Each user| Password (Edit)| Username| User-definable
Password| User-definable
Password Strength| User-definable
Confirm
Refresh
 | Maintain| Log| Log Type| System / CON./ Alarm / Account/ Record / Storage /

Network / All

| Search
---|---|---|---|---|---
Start Time| User-definable
End Time| User-definable
Load Default| All / Video / Record/ Event/ AI/ Network/ Storage / System
Save / Refresh|  |
Upgrade| Path| Search Local Files| Upgrade
Save / Load| Import File| Search Local Files| Import
Export File Name| Search Local Files| Export
Auto Reboot| Auto-maintenance| Enable / Disable
Time| Date / Week / Month
Mon / Tues/ Wed / Thur/ Fri / Sat / Sun
Time
Save / Refresh / Reboot
Information| Serial ID
Device Name
Device Type
Hardware Version
Software Version
Web Version
Mac Address
P2P ID
Refresh

Customising the Day / Night Setting to IR

**** Once logged into the camera browser interface:-

Go To Remote Settings > Video > Image Control > Image Settings

__ e.g. Day / Night mode if want the camera to B&W & use the IR

Suggested setting : IR Cut to Auto

AI Features – IPCND714

The AI smart features can be configured in a ZIP recorder or directly in the browser interface of the camera (standalone)
Only one smart detection feature can be enabled at any given time.
See the NVR or DVR manual for information on configuring these features with a ZIP recorder.
Note :- Additional features may be added at a later date.

PID = Perimeter Intrusion Detection

Perimeter intrusion detection can be set to trigger an alarm event when movement is detected in a set area.

Enable = Enable / Disable this AI feature.
Sensitivity – Determines how much activity or movement is required to generate an event. Options are 1 – 4.
1 = Lowest sensitivity level, a significant amount of movement is needed to trigger.
4 = Highest sensitivity level, only a small amount of moment is needed to trigger.
Detection Type – Options are motion, pedestrian, vehicle or both pedestrian and vehicle.
Rule Number – Up to 4 areas can be set independently in the image area. Use this to enable /disable each of the 4 rules.
Rule Enable – Tick to enable or disable the detection that rule for the rule number selected. Rule Type – The determines how the direction of moment over the perimeter is handled.

A to B (A->B) = Only movement in the direction A to B will trigger. B to A (B->A) = Only movement in the direction B to A will trigger. A or B (A<->B) = Any moment direction over the perimeter will trigger.

LCD = Line Crossing Detection
Line crossing detection can be set to trigger an alarm event when movement is detected across a custom line.

Enable = Enable / Disable this AI feature.
Sensitivity – Determines how much activity or movement is required to generate an event. Options are 1 – 4.
1 = Lowest sensitivity level, a significant amount of movement is needed to trigger.
4 = Highest sensitivity level, only a small amount of moment is needed to trigger.
Detection Type – Options are motion, pedestrian, vehicle or both pedestrian and vehicle.
Rule Number – Up to 4 areas can be set independently in the image area. Use this to enable /disable each of the 4 rules.
Rule Enable – Tick to enable or disable the detection that rule for the rule number selected. Rule Type – The determines how the direction of moment over the perimeter is handled.

A to B (A->B) = Only movement in the direction A to B will trigger. B to A (B->A) = Only movement in the direction B to A will trigger. A or B (A<->B) = Any moment direction over the perimeter will trigger.

General Maintenance

• Routinely clean the camera to prevent dust build up as this can effect the performance of the camera. It is recommended to use a damp non-abrasive microfibre cloth.
• Routinely check the connections for power and data to ensure no water ingress and corrosion.
• Check that the cameras are firmly attached to the wall or mounting bracket.
• Check playback in the recorder to ensure the camera is recording and triggering properly.

Specifications

IPCND714

Conditions

All specifications are approximate. System Q Ltd reserves the right to change any product specifications or features without notice. Whilst every effort is made to ensure that these instructions are complete and accurate, System Q Ltd cannot be held responsible in any way for any losses, no matter how they arise, from errors or omissions in these instructions, or the performance or non-performance of the equipment that these instructions refer to.

This symbol on the products and/or accompanying documents means that used electronic equipment must not be mixed with general household waste. For treatment, recovery and recycling please return this unit to your trade supplier or local designated WEE/CG0783SS collection point as defined by your local council.

© Copyright 2020
NiteDevil is a registered trademark of System Q Ltd, Chesterfield. Derbyshire. S40 2WB

Index

• C
  Checking and cleaning the camera 18
  Connections 3

• D
  Day / Night Setting 14

• E
  Essential Tools and software 2

• I
  Installation 4
  Installing an SD Card 4

• L
  Line Crossing Detection 17
  Login via browser interface 7

• M
  Maintenance 18
  Mounting the camera 4

• P
  Perimeter Intrusion Detection 16

• S
  Setup and Connection Options 5
  Specification 19

NiteDevil.com

References

• NiteDevil: CCTV Cameras That See In The Dark!
• ZipNVR: Home
• System Q Ltd Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>