zelmer ZKR1350 Stand Mixer User Manual
- June 1, 2024
- zelmer
Table of Contents
zelmer ZKR1350 Stand Mixer
ZKR1350
ZKR1355
ZKR1360
WE WOULD LIKE TO THANK YOU FOR CHOOSING ZELMER. WE WISH THE PRODUCT PERFORMS TO YOUR SATISFACTION AND PLEASURE
WARNING
PLEASE READ THE INSTRUCTIONS FOR USE CAREFULLY PRIOR TO USING THE PRODUCT.
STORE THESE IN A SAFE PLACE FOR FUTURE REFERENCE
DESCRIPTION
- Drive shaft
- Release buton
- Head
- Main body
- Speed knob
- Bowl
- Dough hook
- Mixing paddle
- Whisk
- Bowl cover
- Plastic bowl (only models ZKR1355 and ZKR1360)
- Ice cream bowl (only model ZKR1360)
SAFETY INSTRUCTIONS
- If the supply cord is damaged it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Respect the operating times of the accessories indicated in their specific sections of the manual.
- Proceed according to maintenance and cleaning section of this manual for cleaning.
- Warning: potential injury from misuse!
- Always disconnect the appliance from the supply if it is left unattended and before assembling, disassembling or cleaning.
- Switch off the appliance and disconnect from supply before changing accessories or approaching parts that move in use.
- This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
Appliances can be used by persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and
if they understand the hazards involved.
Children shall not play with the appliance.
This appliance is intended for use at a maximum altitude of 2000m above sea
level.
IMPORTANT WARNINGS
- This appliance is designed for home use and should never be used for commercial or industrial use under any circumstances. Any incorrect use or improper handling of the product shall render the warranty null and void.
- Prior to plugging in the product, check that your mains voltage is the same as the one indicated on the product label.
- The mains connection cable must not be tangled or wrapped around the product during use.
- Do not use the device, or connect and disconnect to the supply mains with the hands and / or feet wet. Do not pull on the connection cord in order to unplug it or use it as a handle
- Unplug the product immediately from the mains in the event of any breakdown or damage and contact an official technical support service. In order to prevent any risk of danger, do not open the device. Only qualified technical personnel from the brand´s Official technical support service may carry out repairs or procedures on the device.
- B&B TRENDS SL disclaims all liability for damages that may occur to people, animals or objects, for the non-observance of these warnings.
HOW TO USE THE MACHINE
- To lift the machine head (3), press and hold the release button for lifting and lowering (2). The head (3) will move upward. (RC. 1) (Step 1)
- Place the cover (10) on the mixer body (4) (RC. 2) (Step 2).
- Put the mixing bowl in the holder (RC. 3) (Step 3) and turn it clockwise until it locks into the correct position (RC. 3) (Step 4).
- Install the required accessories (dough hook or mixing paddle or whisk) by inserting the end of the chosen element into the drive shaft (1) (RC. 4) (Step 5) and turn counterclockwise until it locks into the proper position (RC. 5) (Step 6).
- Insert the chosen ingredients. Do not overload the device – the maximum capacity is 1.5 kg.
- Press and hold the release button for lifting and lowering (2). Lower the machine head (3), and the machine will automatically lock the button (2) (RC. 6) (Step 7). If the release button is not held, do not press the head (3) down.
- Connect the plug to a properly installed and secured 220-240V 50-60 Hz socket.
- Start the device using the speed knob (5) selecting speed 1 to 6 according to the processed products. Dough Hook (7): for heavy yeast dough, at speeds 1 or 2. Mixing Paddle (8): for a wide range of ingredients, such as shortcrust pastry, mashed potatoes, pie fillings, icing, etc. at speeds 1-6 depending on the needs. Whisk (9): for whipping cream, eggs (whole, yolks, or whites), or custard, at high speeds (4, 5, and 6).
- For pulsating operation (kneading at short intervals), set the switch to „PULSE.” Hold the switch in this position for the required period. Upon release, the switch automatically returns to the „0” position.
- After kneading/mixing, once the mixture forms a spherical shape, set the speed controller (5) back to the „0” position. Then unplug the appliance.
- Press the button (2) to lift the robot head.
- Use a spatula to detach the mixture and remove it from the mixing bowl.
- You can then remove the mixing bowl.
- Clean the accessories according to the instructions in the „Cleaning” section.
SUGGESTION
Adjusting the Levels and Using the Hook for not more than 1,5kg of Mixture
MAKING ICE CREAM – IN MODEL ZKR1360
NOTE! Only the ZKR1360 model comes with a bowl and accessories for making ice cream.
Before Use
Freezing the Ice Cream Bowl
Before freezing, wash, clean, and dry the ice cream bowl (C).
The ice cream bowl (C), when placed in the freezer, should stand vertically on
a flat surface. The freezing chamber temperature should be lower than -18 ºC,
and the time should exceed 16 hours (preferably freeze overnight and use
during the day). After removing the bowl from the freezer, ensure that it is
completely frozen by gently shaking it. If no flowing liquid is heard, it
means it is frozen.
Using the Ice Cream Accessory
- Freeze the ice cream bowl as explained above.
- Prepare ice cream in advance (up to 700 ml), following the recipe you desire.
- Align the 3 protruding slots at the bottom of the ice cream bowl (C) with the 3 slots in the mixer base. Place the ice cream bowl (C) in the mixer vertically, as shown in Figure 8.
- Insert the connector (A) into the drive shaft (1) of the mixer, as shown in Figure 9.
- Pour the ingredients into the bowl (C).
- Press the mixer head (3) to connect the connector (A) with the mixer (B). See Figure 10.
- Mix for 10-15 minutes at speed 1.
- Serve as a dessert or freeze in a sealed container for later use.
Note: When pouring mixed ingredients into the frozen bowl, turn on the device
within 30 seconds to mix and prevent the edges of the bowl from freezing.
The resulting ice cream is creamy, but if you want it firmer, it is best to
put the bowl with the ice cream in the freezer for an additional 15-25
minutes.
ANALYSIS OF COMMON PROBLEMS
| Problem | Causes | Solutions |
|---|---|---|
| The machine suddenly stops working during use. | It may be that the machine |
runs too long, or the ambient tempe- rature is too high, resulting in the
machine’s motor temperature be- ing too high; the machine starts the
overheating protection program, automatic shutdown.| Gear reset to “0”, unplug
the power, wait for the machine to return to room temperature can be restarted
(generally need 15-30 minutes, the room temperature varies cooling time).
Turning the gear knob machine does not run| Check if the plug is in good
contact with the socket.| Verify that the power plug is plug- ged into the
outlet
Check if the power is out.| Wait for power before operating
Check if the rise button spring back in place.| Make sure the headstock is
stuck in place.
Excessive noise when the machine is running| 1 The machine will work louder in
high gear than in low gear.
2 The amount of food stirred is too large, resulting in overloading the machine.
3 Voltage is unstable.
4 Working time is too long.
| 1 Choose the right gear to stir food according to the recommendations in the manual
2 Reduce the amount of stirring.
3 If the voltage is unstable, wait for the voltage to stabilize before using.
4 If the working time is too long, stop and cool down for a while before using.
The machine speed drops, or the speed is unstable| 1 Whether the room temperature is low, causing the lubricant in the machine to harden.
2 The ingredients stirred are too hard and too much, resulting in too much load on the machine.
3 Whether the voltage suddenly becomes low.
| 1 Remove the mixing bowl and let the machine idle for 5 minutes to soften the lubricant in the machine and restore the speed stability.
2 Reduce the mixing volume and let the machine work according to the normal workload.
3 When the voltage is stable, use the machine again.
---|---|---
Machine swaying and shaking when working| 1 Check if the foot pad on the base
is off.
2 Whether the machine is placed on a smooth and flat countertop for use.
3. Check if the feet are covered with flour dust
| 1 Check if the foot pad on the base is off.
2 Place on a smooth and flat coun- tertop for use
3. Clean the feet from the flower dust
Dough darkening found after use| Black powder falls onto the dough at the mixing head.| Please check that the mixing head and hook are dry and that no water or dust is present on the surface before use.
CLEANING
Body Cleaning| 1. Do not immerse the machine in the water. Do not use water to shower di- rectly on top of the machine to prevent the host body from entering the water to avoid short circuits, electric shock, leakage, rust, and other failures.
2. Do not use a dripping wet towel to wipe the machine
3. Do not use detergent/vinegar/salt and other corrosive, strongly acidic, strong alkaline cleaning products to clean the machine body, otherwise acces- sible to damage the machine’s surface.
4. Do not use sharp and rough tools such as wire balls to brush the acces- sories. Otherwise, it is easy to damage the surface of the accessories.
---|---
Accessory Cleaning| 1. Do not put the cast aluminum parts into the dishwasher
or wash them with corrosive, strongly acidic, or alkaline cleaning products.
Please do not put them into the dishwasher for cleaning. (Except for stainless
steel parts or surface-treated Teflon parts and electrophoresis parts)
2. Do not soak for a long time in detergent, saltwater, vinegar, and other corrosive liquids; use in time to clean accessories.
3. After cleaning, dry the accessories, mainly to keep the internal parts dry in time.
Special Cleaning| 1. The rotating output shaft will produce a bit of black trace due to high speed and friction when the machine is working. After each use, please clean it promptly and keep the part dry.
2. Pay attention to the sharp blade and related sharp edge parts or acces- sories.
Preservation and mainte- nance| 1. You can use olive oil to apply on the blade’s surface, knife plate, and mixing pot to ensure the dry and wet environment to oxidize it.
2. When not in use, you can cover the machine with a packaging bag and place it in a dry environment.
PRODUCT DISPOSAL
This product complies with European Directive 2012/19/EU on electrical and electronic devices, known as WEEE (Waste Electrical and Electronic Equipment), provides the legal framework applicable in the European Union for the disposal and reuse of waste electronic and electrical devices. Do not dispose of this product in the bin, instead going to the electrical and electronic waste collection centre closest to your home.