NiteDevil IP-CAM828 24C Camera Instruction Manual

NiteDevil IP-CAM828 24C Camera

Instruction Manual

NiteDevil 24C Camera IP-CAM828
NiteDevil.com

Part 1 Introduction

1. Key Features – IP-CAM828

Part 2 Connections and Dimensions

1. IP-CAM828

Part 3 Mounting and SD Card Installation

1. Mini-Eyeball

Part 4 Setup Options

1. PoE ZIP NVR
2. Non-PoE ZIP NVR

Part 5 How to log in via Browser
Part 6 Browser Menu Settings

1. IP-CAM828
2. Customizing the Day / Night Setting to IR

Part 7 Extra Resources
Part 8 General Maintenance
Part 9 Specifications

1. IP-CAM828

Index
NiteDevil.com

Introduction

Key Features – IP-CAM828

The NiteDevil HERO IP Camera is a 4K camera that can capture color images in low light conditions. It also has a built-in warning strobe.

Connections and Dimensions

IP-CAM828
The camera can be powered in two ways:

1. 12V DC via the 2.1mm DC socket with a current consumption of 420mA. The camera is polarity sensitive, so connections must be made correctly.
2. PoE 48V RJ45 socket when connecting to a ZIP PoE NVR. Plug the camera directly into the NVR’s built-in PoE switch. After approximately 1 minute of being connected, the camera should become visible.

The camera’s dimensions are provided, excluding the bracket.

Mounting and SD Card Installation
To perform local recording on the camera, an SD card must be installed. The recording time will vary depending on the size of the SD card and encoding settings. The following are the maximum
recording times for different SD card sizes:

• 32GB SD Card: 31 hours
• 64GB SD Card: 62 hours
• 128GB SD Card (MAX): 124 hours
• 256GB SD Card (MAX): 248 hours

The camera can be set to only record when triggered by motion detection, alarm input, or AI smart, maximizing the recording time achievable. Note that power must be removed from the camera when inserting or removing the SD card.

Mini-Eyeball
A template is provided in the box for marking the hole positions for fixing screws.

Setup Options
PoE ZIP NVR
When connecting to a ZIP PoE NVR, plug the camera directly into the NVR’s built-in PoE switch. After approximately 1 minute of being connected, the camera should become visible. The 100m distance for a camera can be increased when the PoE Mode is set to EPoE. In the menu on a ZIP PoE NVR, go to Video > IP Channels > PoE Mode.

Product Usage Instructions

1. Choose one of the two methods to power the camera: either via a 12V DC connection or a PoE 48V RJ45 socket.
2. If performing local recording, install an SD card in the camera. Note that the recording time will depend on the size of the SD card and encoding settings.
3. For optimal recording time, set the camera to only record when triggered by motion detection, alarm input, or AI smart.
4. If connecting to a ZIP PoE NVR, plug the camera directly into the NVR’s built-in PoE switch. In the menu on a ZIP PoE NVR, go to: Video > IP Channels > PoE Mode to increase the distance for a camera when the PoE Mode is set to EPoE.
5. When mounting the camera, use the provided template to mark the hole positions for fixing screws.
6. Remove power from the camera before inserting or removing the SD card.

Key Features – IP-CAM828
4K NiteDevil HERO IP Camera Color in Low Light with a Built-In Warning Strobe

• Full Colour 24/7
• Vehicle Detect
• 4K
• PoE & 12V
• Perimeter cross
• 2-way audio
• NiteDevil® tech
• Line Cross
• SD card slot
• White light LEDs

Connections and Dimensions

IP-CAM828
Powering the camera
Option 1 – Power the camera from 12V DC (via the 2.1mm DC Socket), the current consumption is 420mA. The camera is polarity sensitive so connections must be correctly made.

Option 2 – Power the camera using a PoE 48V RJ45 Socket
When connecting ZIP PoE NVR plug the camera directly into the NVR built-in PoE switch. The camera should automatically become visible after being connected for approximately 1 minute.

Dimensions

Mounting and SD Card Installation
For local recording on the camera itself, an SD card must be installed. Recording time will vary dependent on SD card size and encoding settings

• 32GB SD Card 31 hours
• 64GB SD Card 62 hours
• 128GB SD Card (MAX) 124 hours
• 256GB SD Card (MAX) 248 hours

The camera can be set to only record when triggered via motion detection, alarm input, or AI smart, this maximizes the recording time achievable. Remove power from the camera when inserting/removing the SD card.

Mini-Eyeball
A template is provided in the box for marking the hole positions for the fixing screws.

Setup Options

PoE ZIP NVR
When connecting to a ZIP PoE NVR plug the camera directly into the NVR’s built-in PoE switch. The camera should automatically become visible after being connected for approximately 1 minute. The 100m distance for a camera can be increased when the PoE Mode is set to PoE. In the menu on a ZIP PoE NVR go to:- Video > IP Channels > PoE Mode

Non-PoE ZIP NVR
When connecting cameras to a Non-PoE NVR, they are first connected to an external network switch which is in turn connected to the NVR as shown below. See Extra Resources for more information on Adding IP Cameras manually to
a ZIP Recorder

How to log in via Browser

The AI smart features can be configured in a ZIP recorder or directly in the browser the interface of the camera (standalone) Only one smart detection feature can be enabled at any given time. See the NVR or DVR manual for information on configuring these features with a ZIP recorder. Follow the steps below for configuring the settings directly in the camera via a browser for a standalone setup.
You will need…

• Windows Based PC/ Laptop connected to router/ PoE switch
• ZipVision Pro App on Mobile Devices
• PoE Switch connected to Network/ Router
• Ethernet network cable
• ZipFinder software is available via this link below:- www.softcctv.com/store/Item/Zip-Finder-IP-CCTV-Security-Camera-Discovery-Tool

NOTE If the PC being used is on a different IP range to the PC then add the IP range of the camera to the PC using the below guide:-
PDF Version:- http://www.cctvmanuals.com/pdf/tips/How_to_add_an_IP_Range.pdf
HTML Version:- http://www.cctvmanuals.com/tips/How_to_add_an_IP_Range/index.html

1. Plug the camera’s RJ45 port with a network cable into a PoE switch
2. Using ZipFinder on a Windows Based PC/ Laptop Search and then tick the camera
3. Select Net Mode = DCHP, then click Modify
4. Search again, to get the updated IP address.
5. Select the IP address of the camera, Internet Explorer will pop-up, up and ask you to download and install the plug-in.
6. Download, install, and follow the steps for the plug-in installation, then re-load the browser by selecting the IP address again.
7. log in to the IP Camera, the default login details are:-

Browser Menu Settings
IP-CAM828
The menu be configured directly in the browser interface of the camera (standalone), in Remote Setting you will find the menu settings below:-

Save / Refresh
Image Control| Image Setting| Full Colour Mode / Day / Night Mode / Schedule
White Light| Manual / Automatic mode / Schedule / OFF
Angle Trad| 180 / 0
Mirror| Disable / Vertical / Horizontal / All
Backlight| WDR / HLC / Back Light / Disable
White Balance| Automatic mode / Manual
Shutter| Automatic mode / Manual
Time Exposure| 1/5 to 1/200000 / Flickerless
Defog| OFF / Automatic mode / Manual
3D Noise Reduction| OFF / Automatic Mode / Manual
Save / Default / Refresh
Privacy Mask| Enable / Disable
Record| Encode| Mainstream| Resolution| 3840 x 2160
FPS| 1 -15
Video Code Type| H.265 / H.264
Video Code Level| Main Profile
Bitrate Control| CBR / VBR
Bitrate Mode| Predefined / User-Defined
Bitrate| 512 to 6144
I Frame Interval| 1 to 100
Audio| Enable / Disable
Save / Refresh
Substream| Resolution| 1920 x 1080
FPS| 1 -15
Video Code Type| H.265 / H.264
Video Code Level| Main Profile / Baseline / High Profile
| | | Bitrate Control| CBR / VBR
---|---|---|---|---
Bitrate Mode| Predefined / User-Defined
Bitrate| 128 to 2048
I Frame Interval| 1 to 60
Audio| Enable / Disable
Save / Refresh
Mobilestrea m| Enable| Enable / Disable
Resolution| 640 x 480 / 320 x 240
FPS| 1 – 25
Video Code Type| H.265 / H.264 / H.264+ / H.265+
Video Code Level| Main Profile
Bitrate Control| CBR / VBR
Bitrate Mode| Predefined / User-Defined
Bitrate| 8 to 1536
I Frame Interval| 1 to 60
Audio| Enable / Disable
Save / Refresh
Record| Record| Stream Mode| Mainstream / Substream
Record| Enable / Disable
PreRecord| Enable / Disable
Netbreak| Enable / Disable
Save / Refresh
Schedule| User Definable
Save / Refresh
Event| Setup| Motion| Enable| Enable / Disable
Sensitivity| 1 to 8
Save / Refresh
Deterrence| Save / Default / Refresh
Alarm| Post Recording| OFF / 5s / 10s / 20s / 30s
Send Email| Enable / Disable
FTP Picture Upload| Enable / Disable
Enable Record| Enable / Disable
Deterrent| Enable / Disable
Save / Schedule / Refresh
AI| Setup| PD & VD| Enable| Enable / Disable
Sensitivity| 0 to 100
Snap Mode| Default / Realtime Mode / Interval Mode
Min Pixel| 64 – 1080
Max Pixel| 320 – 1080
Detection Type| Pedestrian & Vehicle / OFF / Person / Vehicle
Detection Mode| Motion Mode / Static Mode
Detection Range| Full Screen / Customize
Save / Refresh
| | LCD| Enable| Enable / Disable
---|---|---|---|---
Sensitivity| 1 to 4
Dynamic Marking| Enable / Disable
Detection Type| Pedestrian & Vehicle / Person / Vehicle
Rule Number| 1 to 4
Rule Enable| Enable / Disable
Rule Type| /            /              B
Save / Refresh
Alarm| PID / LCD| Post Recording| OFF / 5s / 10s / 20s / 30s
Send Email| Enable / Disable
FTP Picture Upload| Enable / Disable
Enable Record| Enable / Disable
Deterrent| Enable / Disable
Save / Schedule / Refresh
Networ k| General| General| DCHP| Enable / Disable
IP Address| User-definable
Subnet Mask| User-definable
Gateway| User-definable
DNS 1| User-definable
DNS 2| User-definable
Video Encryption Transmission| Enable / Disable
Save / Refresh
Port Configura tion| HTTP Port| User-definable
Client Port
HTTPS Port
RTSP Port
P2P Enable| Enable / Disable
Save / Refresh
Email| | Email| Enable / Disable
Encryption| OFF / SSL / TLS / Automatic mode
SMTP Port| 1 – 65535
SMTP Server| User-definable
Username
Password
Sender
Receiver 1
Receiver 2
Receiver 3
Interval
Save / Test / Refresh
RTSP| | RTSP Enable|
Anonymous Login| Enable / Disable
Instruction: rtsp://IP:RtspPort/ch01/A
| | LCD| Enable| Enable / Disable
---|---|---|---|---
Sensitivity| 1 to 4
Dynamic Marking| Enable / Disable
Detection Type| Pedestrian & Vehicle / Person / Vehicle
Rule Number| 1 to 4
Rule Enable| Enable / Disable
Rule Type| /            /              B
Save / Refresh
Alarm| PID / LCD| Post Recording| OFF / 5s / 10s / 20s / 30s
Send Email| Enable / Disable
FTP Picture Upload| Enable / Disable
Enable Record| Enable / Disable
Deterrent| Enable / Disable
Save / Schedule / Refresh
Networ k| General| General| DCHP| Enable / Disable
IP Address| User-definable
Subnet Mask| User-definable
Gateway| User-definable
DNS 1| User-definable
DNS 2| User-definable
Video Encryption Transmission| Enable / Disable
Save / Refresh
Port Configura tion| HTTP Port| User-definable
Client Port
HTTPS Port
RTSP Port
P2P Enable| Enable / Disable
Save / Refresh
Email| | Email| Enable / Disable
Encryption| OFF / SSL / TLS / Automatic mode
SMTP Port| 1 – 65535
SMTP Server| User-definable
Username
Password
Sender
Receiver 1
Receiver 2
Receiver 3
Interval
Save / Test / Refresh
RTSP| | RTSP Enable|
Anonymous Login| Enable / Disable
Instruction: rtsp://IP:RtspPort/ch01/A
| Maintain| Log| Log Type| System / CON. / Alarm / Account / Record / Storage / Network / All| Search
---|---|---|---|---|---
Start Time| User-definable
End Time| User-definable
Load Default| All / Video / Record/ Event / AI / Network/ Storage / System
Save / Refresh| |
Upgrade| Path| Search Local Files| Upgrade
Save / Load| Import File| Search Local Files| Import
Export File Name| Search Local Files| Export
Auto Reboot| Auto-maintenance| Enable / Disable
Time| Date / Week / Month
Mon / Tues / Wed / Thur / Fri / Sat / Sun
Time
Save / Refresh / Reboot
Informatio n| Device ID
Device Name
Device Type
Hardware Version
Software Version
Web Version
Mac Address
P2P ID
Refresh

Customizing the Day / Night Setting to IR
Once logged into the camera browser interface:- Go To Remote Settings > Video

Image Control > Image Settings e.g. Day / Night mode if want the camera to B&W & use the IR Suggested setting: IR Cut to Auto

Extra Resources
ZipNVR.com Website
The Zip NVR has a range of information on the cameras and NVRs, manuals, software, tools, and support:- www.zipdvr.com

Adding IP Cameras to a ZIP recorder
How to guide on Adding IP Cameras:- www.zipdvr.com/howto/TIP459-How-To-Add- IP-Cameras.html

AI Setup
See the ZIP NVR full manual for more information on AI setup;
Note: AI Features will vary depending on the model

Full Instruction Manual

ZIP Firmware
Firmware for the zip products is available online:- www.zipdvr.com/firmware.html Compare the firmware in the product against that available online.

General Maintenance

• Routinely clean the camera to prevent dust build-up as this can affect the performance of the camera. It is recommended to use a damp non-abrasive microfibre cloth.
• Routinely check the connections for power and data to ensure no water ingress and corrosion.
• Check that the cameras are firmly attached to the wall or mounting bracket.
• Check playback in the recorder to ensure the camera is recording and triggering properly.

Specifications

9.1 IP-CAM828

References

• NiteDevil: CCTV Cameras That See In The Dark!
• How to add an IP Range to a Windows PC
• NiteDevil: CCTV Cameras That See In The Dark!
• Zip Finder - IP Camera Discovery Tool - SoftCCTV.com
• ZipNVR: Home
• Zip Finder - IP Camera Discovery Tool - SoftCCTV.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>