phrozen 99531 Wash and Cure Kit User Guide
- June 9, 2024
- phrozen
Table of Contents
Phrozen Wash & Cure Kit User Guide
Washing Station Post Printing Cleaner Scan for other languages
https://phrozen3d.net/oT1AF
99531 Wash and Cure Kit
Specifications
| Control Mode : Knob + Button | Washing Bucket Volume : 8 L |
|---|---|
| Rated Power : 48W | Maximum Model Size : L21.8 x W12.3 x H23.5 cm |
| Input : 24 VCD | Weight : 3.5 kg |
| Product Dimension : L27.7 x W20.7 x H46.7 cm | Timer : 0 – 30 minutes |
Before You Start
- Place the machine on a clean and level surface.
- Put the washing basket into the bucket.
- Please make sure to wear protective goggles, gloves, masks, and long-sleeved clothing when handling the machine.
- Pour in an appropriate amount of alcohol (95%) or other cleaning fluid (Phrozen Wash).
- Cover the bucket when the machine is in use to avoid splashing and objects falling.
- Keep the bucket covered to avoid alcohol evaporation when the machine is not in use.
Instructions
- After printing is completed hang A the building plate with prints on the cleaning basket (if the building plate is smaller than 7”, use the basket holder). B For building plate over 10” put the prints straight into the cleaning basket.
- Turn the knob to adjust the time and press to set. It is recommended that each cleaning time should not exceed 30 seconds as overcleaning might damage the prints.
- After the timer stops, lift the basket vertically and take out the prints.
- Leave prints to dry or use an air gun to accelerate the drying process.
- For hollow and more complicated models, please make sure the prints are clean. If any residual resin was found, repeat steps 2-5.
- After the cleaning process is completed, put prints into the curing machine to cure.
Note : Regularly replace 95% alcohol (cleaning fluid) for optimum results.
Warning
- Please disconnect the power before cleaning or replacing alcohol (cleaning fluid).
- DO NOT pour resins or other liquid except alcohol (cleaning fluid) into the cleaning bucket.
- Avoid direct contact with skin to prevent allergies.
- In case of contact with resin and alcohol (cleaning fluid), please rinse immediately with plenty of water.
- DO NOT remove prints from the bucket when the machine is running.
Specifications
| Rated Power : 48W | Maximum Model Size : Ø25 x H23.5 cm |
|---|---|
| Input : 24 VCD | Weight : 3.9 kg |
| Product Dimension : L35.4 x W30.9 x H36.8 cm | Timer : 0-2 hours |
| Turntable Size : Ø19.6 cm | LED Wavelength : 405 nm |
Before You Start
- Place the machine on a clean and level surface.
- Install the turntable into the machine and connect the power.
- Please make sure to wear protective goggles when handling the machine.
- Do not remove or lift the acrylic cover when the machine is running.
Instructions
- Make sure the model has been thoroughly cleaned without any residual resin before curing.
- Place the model on the turntable and put the acrylic cover into place.
- Select CURE, FAN, or FAN + CURE according to your needs.
- Input the required time and press ENTER. Timer settings are available for up to two hours.
- Please take out the model after the curing process ends.
Note : Cured model might reach higher temperatures; please remove it carefully.
Warning
- Disconnect the power cable before performing maintenance.
- DO NOT take off the acrylic cover while the machine is running.
- Avoid direct contact of resin and other cleaning fluid with skin to prevent allergies.
- In case of contact with resin and alcohol (cleaning fluid), please rinse immediately with plenty of water.
| Help Center | |
|---|---|
| https://phrozen3d.net/uK6Ka | https://lihi1.com/bQ3w0 |
| YouTube | |
| https://lihi1.com/U7iyD | https://lihi1.com/naYk0 |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>