phrozen Mini 8K S Resin 3D Printer User Manual
- October 30, 2023
- phrozen
Table of Contents
Mini 8K S Resin 3D Printer
User Manual
Dear User,
Thank you for joining us. Please read the Sonic Mini 8K S manual thoroughly
and follow the instructions step by step to get the best printing experience.
Introduction
Printer Parts
The Toolbox
Operation
System Phrozen OS
Operation 3.5 inch Touch Panel
Slicer Software Tango Slicer or Others
Connectivity Side USB Port
Printing Specifications
Technology Resin 3D Printer – LCD Type
Light Source Linear Projection LED Module
XY Resolution 22 pm
Layer Thickness 0.01-0.30 mm
Max Printing Speed 80 mm / hr
Power Requirement 24VDC ; 2A
Power Max 48W
Hardware Specifications
Printer Size 29 x 29 x 43 cm
Printing Volume 16.5 x 7.2 x 17 cm
Printer Weight 10 kg
Key Notes Before Start
Stable Printing Environment
Store your 3D printer in a dry and ventilated environment. Avoid exposure
to direct sunlight. Make sure to place the printer on a flat surface.
Protective Measures
While printing and using resin, please make sure to wear gloves, masks,
protective goggles, and long-sleeved clothing.
Maintenance
Clean the Z-axis
First, dry clean the Z-axis T-screw. Then apply a thin layer of general
lubricant on it, so that it whirls smoothly.
Clean the 3D Printe r
Use sanitizing alcohol and tissue paper to carefully clean the printer, the
resin vat, and the building plate. Prepare Your 3D Printer
For first-time use, please thoroughly follow the steps down below to
calibrate your Z-axis and conduct the LCD Test so that your 3D printer is
ready.
LCD Test
-
Click on TOOLS. Then click on LCD TEST.
-
**** Check to see if the LCD screen displays the same image as seen on the touch panel.
-
**** When the LCD screen clearly displays the image, the LCD TEST is complete.
Z-axis Calibration
- Click on TOOLS. Then click on Z CALIB.
- Remove the resin vat and place an A4 paper on the LCD. Loosen all 4 screws on the sides of the building plate.
- Click on NEXT, and wait until the building plate touches the LCD screen.
- Then tighten the 4 screws. Make sure paper is unmovable, then click on DONE to finish calibration.
- Wait until the building plate retracts to the TOR Z-axis Calibration is now complete.
Perform the Printing Test
After conducting the Z-axis Calibration and LCD TEST, let’s move on to the
Printing Test.
Prepare Your PRZ File
The Sonic Mini 8K S only supports PRZ file format.
Use slicer software to turn STL and OBJ files into PRZ files.
Convert STL/OBJ File to PRZ File
- Import STL or OBJ files into the slicer software. Choose “Sonic Mini 8K S” printer and set the resin parameters according to the resin used, and start slicing.
- After the slicing is completed, save it as a PRZ file and your 3D model file is ready to be printed.
Test Files for Your First Print
- The USB included in the tool box contains both STL and PRZ files of two test models: “Phrozen_test” and “Phrozen_XP Finder”.
- You can directly print the PRZ files in the USB with Aqua-Gray 8K Resin. If you are printing with other resins, slice the STL files with the compatible parameter settings required for your resin.
Printing Test
- Please make sure the bottom screws of the resin vat are perfectly aligned with the platform grooves, then tighten the screws on both sides. When placing the resin vat, please pay attention to the bottom screws and DO NOT damage the LCD screen.
- Shake the resin bottle for 1 minute. When pouring, make sure the resin does not exceed the max fill line on the resin vat.
- Insert your USB into Sonic Mini 8K S. Choose the file and click GO to begin printing.
- Keep the plastic case closed during printing to prevent exposure to excessive UV light.
- After printing, carefully remove the building plate and then tilt and place it onto a desk or a flat surface. Use a metal scraper to carefully remove your print.
Use Z-Offset to Set your Z-Axis Zero Position
After calibrating the Z-axis, you can use this function to modify your
Z-axis zero position, if needed. Use this function if you are looking to print
flat on the building plate or if the resin flow is slow.
Click the following buttons on the touchscreen: TOOLS > Z CONTROL > START >
0.1mm up > Z-Offset > SET
Tips: If you use Z CALIB, or reset the Z-Offset, orflash the firmware,
the device will be reset to Z-Axis Zero Position.
After-sales service & warranty
- Phrozen offers a one-year warranty for all parts, excluding consumable components such as the LCD screen and FEP film.
- Sonic Mini 8K S LCD screen is covered under a 3-month warranty. Please note that this warranty does not cover any damages caused by human
- If you encounter any difficulties, please scan the QR codes down below to contact us.
Contact us!
Congratulations!
You have just completed your first run. We hope you’ve had a great experience!
Please follow Phrozen’s social media accounts and subscribe to our YouTube
channel to learn more about printing tips and share information with the
community.
Facekbook Page
| Facebook User Group| YouTube| Instragram
---|---|---|---
| | |
<https://lihi1.com/pA4Tw>|
<https://lihi1.com/up8mu>|
<https://lihi1.com/U7iyD>|
<https://lihi1.com/naYk0>Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>