phrozen 5 IPS Sonic Mega 8K Instruction Manual

phrozen 5 IPS Sonic Mega 8K

Product Specifications

• Model: Sonic Mega 8K
• Technology: LCD USB
• Operating System: Phrozen OS
• Layer Resolution: 0.01-0.30 mm
• Power Input: AC100-240V 50-60Hz
• Dimensions (mm): 47.5 x 40 x 68 (Printer), 33 x 18.5 x 40 (LCD)
• Weight (kg): 35

Product Usage Instructions

Printing:
To initiate a print job, follow these steps:

1. Prepare your STL file in CHITUBOX software.
2. Connect the printer to your computer via USB.
3. Load the prepared file onto the printer’s memory.
4. Select the desired print settings on the LCD screen.
5. Start the print job and monitor progress.

Cleaning:
To clean the VAT, follow these steps:

1. Remove the VAT from the printer carefully.
2. Clean any resin residue with a suitable cleaning solution.
3. Rinse the VAT with clean water and dry it thoroughly before reinstallation.

LCD Calibration:
To calibrate the LCD screen, follow these steps:

1. Access the LCD calibration tool in the printer menu.
2. Follow the on-screen instructions to adjust settings for optimal display.
3. Confirm and save the changes before exiting the calibration mode.

Frequently Asked Questions (FAQ):

• Q: How can I troubleshoot printing issues?
  A: If you encounter printing problems, ensure that the resin tank is properly leveled and clean. Also, check for any obstructions in the build platform or resin tank.

• Q: What is the recommended maintenance schedule for this printer?
  A: Regularly clean the print platform, VAT, and resin tank after each use. Perform LCD screen calibration monthly to ensure accurate printing results.

Dear User , Thank you for joining us. Please read the Sonic Mega 8K manual thoroughly and follow the instructions step by step to get the best printing experience.

Introduction

The Toolbox

Operation

Printing Specifications

Hardware Specifications

•  All specifications were tested in a laboratory and are subject to change without prior notice. For the latest update, please refer to Phrozen’s official website.
• The included power cord set packaged with the main unit cannot be used with electrical equipment other than the specified device.

Key Notes Before Start

DO NOT Calibrate the Z-axis or Disassemble the 3D Printer.
Sonic Mega 8K comes with a pre-calibrated building plate. Please DO NOT calibrate the Z-axis or disassemble the 3D printer on your own, as this may damage the 3D printer and cause your warranty to become invalid. In order to prevent damage against the LCD screen, please DO NOT install a screen protector NOR switch building plates with any other 3D printers as it may cause calibration failure

If you have any technical questions, please scan the QR codes to contact us.

• Stable Printing Environment
  Store your 3D printer in a dry and ventilated environment. Avoid exposure to direct sunlight. Make sure to place it on a flat surface.

• Protective Measures
  While printing and using resin, please make sure to wear gloves, masks, protective goggles, and long-sleeved clothing.

Maintenance

• Clean the Z-axis
  First, dry clean the Z-axis T-screw. Then apply a thin layer of general lubricant on it, so that it whirls smoothly.

• Clean the 3D Printer
  Use sanitizing alcohol and tissue paper to carefully clean the printer, the resin vat, and the building plate.

Prepare Your 3D Printer

For first-time use, please thoroughly follow the steps down below to conduct the LCD Test so that your 3D printer is ready to print.

LCD Test

1. Click on TOOLS. Then click on LCD TEST.
2. Check to see if the LCD screen displays the same image as seen on the touch panel.
3. When the LCD screen clearly displays the image, the LCD TEST is complete.

Please refer to the actual operation situation based on the printer display:

Import Your 3D File

After preparing your 3D print files, there are 2 ways to import your files onto the Sonic Mega 8K: via Ethernet or USB.
Prepare Your 3D File

1. On your computer, import the STL file to CHITUBOX, V1.9.0 or above.
2. Click settings to add a new printer “Sonic Mega 8K.” Set your Print Parameters according to the resin you will use.
3. Slice the 3D file and save it as CTB: file, before importing it to your 3D printer.

Please refer to the resin profile for the updated printing parameters and use the XP_Finder in the USB to find the optimal printing parameters.

Importing via Ethernet

1. Insert the USB and connect your printer to the same router as your computer.

2. Click on TOOLS, and select NETWORK to check the IP address of the 3D printer.
   The 1P address in the following photo is for reference only.

3. Operate CHITUBOX on your computer. After slicing your 3D file, click on “Network Sending”: to send you file to the printer.

4. Make sure to select CHITUBOX slicer .ctb) as your file type before sending it over to your 3D printer’s IP address.

5. After successfully sending over your file, click on “OK” to start printing immediately.

6. If not, click on “Cancel”, the file will directly be stored onto the USB drive plugged onto your printer.

Importing via USB

1. Save the CTB file in the USB and insert it into the 3D printer.
2. Click on PRINT and choose your file to begin nrintinal

Perform the Printing Test

Printing Test

1. Use both hands to tighten the screws and fasten the resin vat at the same time.
2. Make sure that both the resin vat and the building plate are parallel to the printer. The surface should be clean. Shake the resin bottle for 1 minute. When pouring,
3. make sure the resin does not exceed the mark on the resin vat.
4. Import your ctb. file into Sonic Mega 8K: Then select the file and click GO to begin printing.
5.  While printing, please keep the chamber closed to prevent the 3D prints from distorting in shape.
6. Once printing is complete, please use both your hands and carefully remove the building plate to prevent damage against the LCD screen.
7. Tilt and place the building plate onto a desk and use a metal scraper to carefully remove your print.
8. Use 95% sanitizing alcohol or Phrozen Wash Resin Cleaner to rinse your printed model. Then cure your models with a Post-Curing Chamber, After curing, your first print is complete.

After-sales service & warranty

• Phrozen offers a one-year warranty for all parts, excluding consumable components such as the LCD screen and FEP film.
• Sonic Mega 8K LCD screen is covered under a 3-month warranty. Please note that this warranty does not cover any damages caused by human factors.
• If you encounter any difficulties, please scan the QR codes down below to contact us.

Congratulations!

• You have just completed your first run. We hope you’ve had a great experience
• Please follow Phrozen’s social media accounts and subscribe to our YouTube channel to learn more about printing tips and share information with the community.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>