NEXTTORCH WL50IR Dual Tactical Light User Manual

: June 5, 2024
: NEXTTORCH

Table of Contents

SPECIFICATIONS
FEATURES
QUICK START GUIDE
PRODUCT INSTRUCTION
NOTE
MAINTENANCE
WARRANTY
CONTACT WITH NEXTORCH DESIGNER
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WL50 IR
Leam more on www.nextorch.com

SPECIFICATIONS

ANSI / PLATO-FL1	Battery	White Light	IR
Light Output	2 x CR123A	High	Medium
860 Im	330 Im	140 Im

Above tested specifications are strictly based on the standard of ANSI / PLATO-FL1. We tested WL50 IR with a standard 18650 (2600 mAh) battery or Energizer 2 × CR123A batteries in 22 ± 3. The specifications might be different when using a different battery or testing in a different environment

FEATURES

Integral Picatinny rail clamp securely attaches/detaches quickly without using tools
Maximum output up to 860 lumens
Three selectable modes: High-Mid-Low, respectively for white light and IR mode under different tactical conditions
Simply twist the front knurled portion of the bezel to switch between the two light-spectrum modes: white-light and IR mode-no IR filter required
Push-button tail switch or remote pressure switch features tactical momentary and constant on operation
Powered by either 2 × CR123A lithium batteries or by 1 × 18650 rechargeable lithium-ion battery

QUICK START GUIDE

Battery Replacement
Remove the tail cap to install/remove batteries. Place two CR123A batteries (with the loading tube) or one rechargeable 18650 battery inside, and then tighten the tail cap
Mounting
The rail clamp is designed to rapidly and securely attach/detach from Picatinny rail
1. Make sure your rifle with a picatinny rail, and find out he mounted position
2. Rotate the thumb wheel to make the clamp fully open, and adjust the rail block to fit the picatinny rail of your rifle
3. Securely mount the clamp over the Picatinny rail of your rifle and retighten the thumb wheel to finish
Remote Switch Installation
Option a: attach the remote switch to any desired position
1. Tear away covers of the double-sided tape, which is included
2. Securely attach one sticky side to the back of the switch
3. Attach the remote switch to your preferred position via self-stick velcro backing
4. Fasten the self-stick velcro tightly to finish
Option b: attach the remote switch over the picatinny rail
1. First attach the included remote retaining clips to the pictinny rail forend
2. Then securely mount the remote switch on the remote retaining clips
3. Complete as shown below

PRODUCT INSTRUCTION

Mode Introduction

Mode Selection: rotate the tail-cap thumb wheel to switch among
High→Mid→Low→OFF

Switch Operation
It uses either a remote pressure switch or a standard push-button tail switch

Switch Replacement
Twist to remove the standard push-button tail switch, then plug your remote pressure switch

NOTE

When not on duty, avoiding staring into beam. May be harmful to eyes, especially IR
Do not remove the head of the light in case of the reflector or LED being broken
When not using WL50 IR, untighten the tail-cap or turn it off

MAINTENANCE

Being infected with seawater or any corrosive chemicals, please rinse immediately with clean water.
Please use high quality batteries; Remove batteries when not working for a long time, and then store in a cool dry place.
Replace waterproof O-ring immediately when considering of the damage with use.

WARRANTY

NEXTORCH warrants our products to be free from any defects in workmanship and/or materials for a period of 15-day from the date of purchase. We will replace it. NEXTORCH reserves the right to replace an obsolete product with a current production, like model.
NEXTORCH warrants our products to be free of defect for 5-year of use. We will repair it.
The warranty excludes other accessories, but rechargeable batteries are warranted for 1year from the date of purchase.
In the event that any issue with a NEXTORCH product is not covered under this warranty, NEXTORCH can arrange to have the product repaired for a reasonable fee.
You could access to NEXTORCH website (www.nextorch.com) to gain warranty service information by scanning the following QR code.You could also:
Email us at service@nextorch.com
Call us: 0086-400-8300-799
OR contact your local dealer/distributor.

http://www.nextorch.com/en/index.php/aftersales

CONTACT WITH NEXTORCH DESIGNER

In order to improve NEXTORCH, we appreciate you could offer our designers your after-use feedback and creative suggestions by scanning the following QR code. Thank you!

|
---|---

http://weixin.qq.com/r/VfHK0oDEHd1ircSx96RH

|

https://www.facebook.com/nextorchlight