BRESSER 7004200000000 Temp Weather Station Instruction Manual

Weather Station · Wetterstation ·
Meteo Temp

7004200000000
Instruction manual

7004200000000 Temp Weather Station

Visit our website via the following QR Code or web link to find further information on this product or the available translations of these instructions.

|
---|---
www.bresser.de/P7004200| www.bresser.de/P7004200000000

www.bresser.de/warranty_terms

Imprint (German)

Bresser GmbH
Gutenbergstr. 2
46414 Rhede
Germany
www.bresser.de

For any warranty claims or service inquiries, please refer to the information on “Warranty” and “Service” in this documentation. We ask for your understanding that unsolicited returns cannot be processed.
Errors and technical changes excepted.
© 2022 Bresser GmbH
All rights reserved.

The reproduction of this documentation – even in extracts in any form (e.g. photocopy, print, etc.) as well as the use and distribution by means of electronic systems (e.g. image file, website, etc.) without the prior written permission of the manufacturer is prohibited.
The designations and brand names of the respective companies used in this documentation are generally protected by trade, trademark and/or patent law in Germany, the European Union and/or other countries.

Validity note

This documentation is valid for the products with the following article numbers:
7004200 7004200000000

Manual version: 0822
Manual designation:
Manual_7004200000000_Meteo-Temp_en- de_BRESSER_v082022a
Always provide information when requesting service.

About this Instruction Manual

NOTICE
These operating instructions are to be considered a component of the device.
Read the safety instructions and the instruction manual carefully before using this device.
Keep these instruction manual in a safe place for future reference. If the device is sold or passed on, the instruction manual must be passed on to any subsequent owner/user
of the product.

General safety instructions

DANGER
Danger of suffocation!
Improper use of this product may result in suffocation, especially for children. It is therefore imperative that you observe the following safety information.

• Keep packaging materials (plastic bags, rubber bands, etc.) away from children! There is a danger of choking!
• This product contains small parts that can be swallowed by children! Choking hazard!

DANGER
Risk of an electric shock!
This device contains electronic parts that are powered by a power source (AC adapter and/or batteries). Improper use of this product may result in electric shock. Electric shock can cause serious or fatal injuries. It is therefore imperative that you observe the following safety information.

• Never leave children unattended when handling the device! Follow the instructions carefully and do not attempt to power this device with anything other than power sources recommended in this  instruction manual, otherwise there is a danger of an electric shock!

DANGER
Explosion hazard!
Improper use of this product may result in fire. It is essential that you observe the following safety information in order to avoid fires.

• Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the device or batteries, or throw them into a fire! Excessive heat or improper handling could trigger a short-circuit, a fire or an explosion!

NOTICE
Danger of material damage!
Improper handling may result in damage to the unit and/or accessories. Therefore, use the device only in accordance with the following safety information.

• Do not disassemble the device! In the event of a defect, please contact your dealer. They will contact the Service Center and can arrange the return of this device for re-
  pair if necessary.

• Do not immerse the unit in water!

• Do not expose the device to impacts, vibrations, dust, constant high temperatures or excessive humidity. This can result in malfunctions, short-circuits or damage to the batteries and components.

• Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or types or with different capacities. Remove batteries from the device if it is not to be used for a longer period of time!

NOTICE
Risk of voltage damage!
The manufacturer is not liable for damage related to improperly installed batteries!

Parts overview and scope of delivery

Illustration 1: Parts overview for base station (top) and remote sensor (bottom)

1. Display (Base station)
2. UP button (Value setting upwards)
3. DOWN button (Value setting downwards)
4. SYNC button
5. SET button (Settings and display change between °C or °F)
6. Battery compartment
7. Stand, fold-out
8. Wall mount
9. Battery compartment lid
10. Wall mount
11. Battery compartment

What’s Included:
Base station (A), remote sensor (B)
Required batteries (not included):
Station: 2 pcs. Mignon batteries (1.5V, type AAA)
Sensor: 2 pcs. Mignon batteries (1.5V, type AAA)

Screen display

Illustration 2: Screen display for the base station

1. Time
2. Symbol for active daylight saving time (DST)
3. Weather trend arrow
4. Graphical 12-24 hours weather trend display
5. Signal reception symbol (remote sensor)
6. Temperature range symbol (remote sensor)
7. Outdoor temperature value (remote sensor)
8. Battery level indicator (remote sensor)
9. Temperature range symbol (base station)
10. Indoor temperature value (base station)
11. Battery level indicator (base station)
12. Time signal transmission symbol
13. Day and Month
14. Ice pre-alert

Before commissioning

NOTICE
Avoid connection faults!
In order to avoid connection problems between the devices, the following points must be observed during commissioning.

1. Place the base unit (receiver) and sensor (transmitter) as close together as possible.
2. Connect the power supply to the base unit and wait until the indoor temperature is displayed.
3. Establish power supply for the sensor.
4. Set up/operate the base unit and sensor within the effective transmission range.
5. Make sure that the base unit and the radio sensor are set to the same channel.

When changing the batteries, always remove the batteries from both the base unit and the sensor and reinsert them in the correct order so that the radio link can be re-established. If one of the two devices is operated via a mains power connection, the power connection must also be briefly disconnected for this device when the batteries are changed. If, for example, only the batteries in the sensor are replaced, the signal may subsequently not be received at all or not be received correctly.
Note that the actual range depends on the respective construction materials used for the buildings as well as the respective position of the base unit and the outdoor sensor.
External influences (various radio transmitters and other sources of interference) can greatly reduce the possible range. In such cases, we recommend finding other locations
for both the base unit and the outdoor sensor. Sometimes moving the sensor by just a few centimeters is enough!
Though the remote unit is weather proof, it should be placed away from direct sunlight, rain or snow.

Setting up power supply

Base station

1. Remove the battery compartment cover.

2. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

3. Replace the battery compartment cover.
   Remote sensor

4. Remove the battery compartment cover.

5. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

6. Replace the battery compartment cover.

Automatic time setting

After the power supply was established, the clock will automatically search for the radio signal. This will take approximately 3 to 8 minutes to finish this process.
If the radio signal is received correctly, the date and time will be set automatically and the radio control signal icon turns on.
If the clock fails to receive the time signal, go ahead with the following steps:

1. Press and hold the UP button for 2 seconds to re-initialize RC signal receiving.
2. Is the device still not receiving the signal, the time must be set manually.

Manual time setting

1. Press the SET button for approx. 3 seconds to enter the time setting mode.
2. Digits to be set are flashing.
3. Press UP or DOWN button to change the value.
4. Press the SET button to confirm and switch to the next setting.
5. Order of settings: Time zone (-12 to +12 hours) > Year > Month > Day > Month (M) and Day (D)/Day (D) and Month (M) > 12/24 hour mode > Hours > Minutes
6. Finally, press the SET button to save the settings and exit setting mode.

Time zone setting

The time zone is set as part of the manual time setting. Further information can also be found in the chapter “Manual Time Adjustment”.

1. Press the SET button for approx. 3 seconds to enter the time setting mode.
2. Possibly press the SET button several times until the display shows the setting for the time zone (the factory setting is ’00’).
3. Press UP or DOWN button to select the desired time deviation in hours (-12 to +12 hours).
4. Finally, press SET button for approx. 3 seconds to confirm the set time deviation.

Receiving measurements automatically

Once batteries are installed, the base station will display the measurement readings. Readings from the remote sensor will be displayed within 3 minutes after powering it on.
If no signal will be received, then go ahead with the following steps:

1. Press SYNC button for approx. 2 seconds to re-initiate reception of measurements again.
2. If the device is still not receiving the signal: Press and hold the DOWN button for approx. 2 seconds to initiate reception of measurements again.

Weather trend

The weather station will calculate a weather trend for the next 12-24 hours on basis of the measured values.

1. Sunny
2. Partly cloudy
3. Cloudy
4. Rain
5. Snow

Trend arrow indicators

1 Rising
2 Steady
3 Falling

The temperature trend indicator shows the trends of changes in the forthcoming few minutes. Arrows indicate a rising, steady or falling trend.

Ice pre-alert

1. When the outdoor temperature hits 3° C (37 ° F), the ice pre-alert symbol will appear on the display, flashing continuously.
2. The ice pre-alert symbol will disappear as soon as the temperature rises above 6° C.

Disposal

Dispose of the packaging materials according to its type. Information on proper disposal can be obtained from the municipal waste disposal service provider or  environmental agency.
Do not dispose of electronic devices in the household garbage!
According to the European Directive 2012/19/EU on Waste Electrical and Electronic Equipment and its transposition into national law, used electrical equipment must be collected separately and recycled in an environmentally sound manner.
**** Batteries and rechargeable batteries must not be disposed of with household waste. You are legally obliged to return used batteries and accumulators and can return them after use either at our sales outlet or in the immediate vicinity (e.g. in the trade or in municipal collection points) free of charge. Batteries and accumulators are marked with a crossed-out dustbin and the chemical symbol of the pollutant, “Cd” stands for cadmium, “Hg” stands for mercury and “Pb” stands for lead.

Technical data

Base station

Wireless Rain gauge sensor

Warranty

The regular warranty period is 2 years and starts on the day of purchase. To benefit from an extended voluntary warranty period as indicated on the gift box, registration on
our website is required.
You can consult the full guarantee terms as well as information on extending the guarantee period and details of our services at www.bresser.de/warranty_terms.

EC declaration of conformity

**** Bresser GmbH hereby declares that the radio equipment type with item number 7004200 7004200000000 is in compliance with Directive 2014/53/EU. The full text of the EC Declaration of Conformity is available at the following web address: www.bresser.de/download/7004200/CE/70004200_CE.pdf

UKCA declaration of conformity

A “Declaration of Conformity” in accordance with the applicable directives and relevant standards has been issued by Bresser GmbH The full text of the UKCA Declaration of Conformity is available at the following web address:
www.bresser.de/download/7004200/UKCA/70004200_UKCA.pdf
Bresser UK Ltd. • Suite 3G, Eden House, Enterprise Way, Edenbridge, Kent TN8 6HF, Great Britain

Service

Please contact the service centre first for anyquestions regarding the product or claims,preferably by e-mail.

e-mail: service@bresseruk.com
Telephone*: +44 1342 837 098
BRESSER UK Ltd
Customer Support
Suite 3G, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
United Kingdom

• Number charged at local rates in the UK (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.

Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de

@BresserEurope

References

• disponibles.IT
• konsoleH :: Login
• Bresser | Startseite | Expand Your Horizon mit BRESSER
• index · powered by h5ai 0.26.1 (http://larsjung.de/h5ai/)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>