Akuvox TZ-SM-002347 X912 Vandal-Resistant Door Phone for High-End Buildings User Guide
- June 9, 2024
- Akuvox
Table of Contents
Smart Intercom
X912 Quick Guide
Unpacking
Before you being using the device, please check the version you obtained and
ensure that the following items are included in the shipped box :
Mainframe Accessories :
![Akuvox TZ SM 002347 X912 Vandal Resistant Door Phone for High End Buildings
- Fig](https://manuals.plus/wp-content/uploads/2023/01/Akuvox-TZ- SM-002347-X912-Vandal-Resistant-Door-Phone-for-High-End-Buildings-Fig.jpg)
Product Overview
![Akuvox TZ SM 002347 X912 Vandal Resistant Door Phone for High End Buildings
- Fig1](https://manuals.plus/wp-content/uploads/2023/01/Akuvox-TZ- SM-002347-X912-Vandal-Resistant-Door-Phone-for-High-End-Buildings-Fig1.jpg)
Installation Environment
Please do not place device under direct sunlight.
If installing the device indoors , please keep device at least 2 meters away
from light, and a t least 3 meters away from window and door.
Attention:
Biometric recognition product may not be considered 100% accurate in any
identification application.
For higher security purpose or scenario, please set up access authentication
along with biometric recognition.
Installation
Wall-mounting Bracket Installation
Put the wall-mounting template on wall, then according to the wall-mounting
template use a hand drill to make the hole in marked holes (6 mm in diameter
and 20mm in depth) .
Insert the five plastic wall anchors into the drilled holes. Place the wall-
mounting bracket closely against the wall while lining up its five wire holes
with their corresponding drilled holes. And then fasten the wall-mounting
bracket on the wall by tightening five ST4x20 crosshead screws to the plastic
wall anchors.
Hang the one end of the rope onto the square hanger pin on the wall-mounting
bracket. Choose a suitable size rubber plug (small, large and medium) to hold
down the wires, while tearing off the adhesive sticker on the selected rubber
plugs and plug them into the back cover in the position as indicated in the
drawing. Connect the network cables to the corresponding interface of the
mainboard, then connect the signal wire to the corresponding connection holes.
Note: all the cables and wires must go through the opening at the rubber
plug position. Fasten the wiring cover onto the back cover using four M3X4
crosshead screws. Line up the four slots at the back cover with the four hanging
hooks, then hang the back over onto hooks while pressing down the whole device
vertically against the hook, and let the bottom hole of the device fall down
onto the hanger pin. You will hear clattering sound before installation
completion. Check if the gap surrounding the device is even. Push up the
device from the device’ s bottom to check if the device is securely installed.
And please remove the protective film.
Device Removal
Insert the alien wrench into the left side hole at the bottom of the device, and turn the wrench 90 degrees clockwise, and push the device up vertically until the hanger pin and the device are disengaged.
Device Wiring
Warning
When you connect a device containing a coil, such as a relay oran
electromagnetic lock, it is necessary to protect the intercom against voltage
peak while switching off the induction load. For this way of protection we
recommend adiode — 1A/ 200 V (included in the accessories) connected
antiparallet to the device.
![Akuvox TZ SM 002347 X912 Vandal Resistant Door Phone for High End Buildings
- Fig12](https://manuals.plus/wp-content/uploads/2023/01/Akuvox-TZ- SM-002347-X912-Vandal-Resistant-Door-Phone-for-High-End-Buildings-Fig12.jpg)
Wire Length & AWG Table
Please follow the properly measured wire gauge/length to install device:
| 20 AWG| 22 AWG| 24 AWG| 26 AWG
---|---|---|---|---
12V 1 A Adapter| ≤20m| ≤10m| | \
Application Network Topology
![Akuvox TZ SM 002347 X912 Vandal Resistant Door Phone for High End Buildings
- Fig13](https://manuals.plus/wp-content/uploads/2023/01/Akuvox-TZ- SM-002347-X912-Vandal-Resistant-Door-Phone-for-High-End-Buildings-Fig13.jpg)
Configuration
- IP address Checking: Press key Icon on the home interface or on the dial pad, then press 2396 and bell Icon to enter the system interface, and press System Information to check the device IP address. X912 uses DHCP by default.
- Account Registration: On the web interface, go to the path Account > Basic page to register and fill in the account information. (Please refer to user manual for more information)
Operation
Make a call:
Enter the IP or SIP number and press bell Icon to make a call.
Receive a call:
X912 supports Auto Answer by default. Incoming call from indoor device will be
answered automatically.
Unlock by PIN:
Press Key Icon on the home interface or on the dial pad, then enter the PIN
code, and press the Key Icon on the dial pad for the confirmation.
Unlock by RF Card:
Place the configured RF card on the card reader area for the door access.
Note Information
Information contained in this document is believed to be accurate and reliable at the time of printing. This document is subject to change without notice, any update to this document can be viewed on Akuvox’ s website: http://www.akuvox.com © Copyright 2022 Akuvox Ltd. All rights reserved.
AKUVOX (XIAMEN) NETWORKS CO., LTD.
Add.: 10/F, NO.56 GUANRI ROAD, SOFTWARE PARK II, XIAMEN 361009, CHINA
www.akuvox.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>