AKUVOX C319 Series C319X Smart Indoor Monitor User Guide
- June 4, 2024
- Akuvox
Table of Contents
C319X
Quick Guide
Unpacking
Before you start using the device, please check the version you got and ensure that the following items are included in the shipped box:
| Plastic wall anchors x 4
---|---
| ST4x20 crosshead screw x 4
| Diode x 4
| M3x6 crosshead screw x 1
| M3x10.5 hex socket screw x 1
| Allen Wrench x 1
| 10 Pin cable x 1
| 11 Pin cable x 1
| C319X x 1
| Wall-mounting bracket x 1
| M4x30 crosshead screw x 4
Product Overview
Front Panel
|
Right View
---|---
Installation
Step 1: Wall-mounting Bracket Installation Without embedded box in the wall
| According to the position of the cable in the wall, dig out a square
hole(heightwidthdepth =665050 mm) that can accommodate all cables.
---|---
| Align the square hole of the wall-mounting bracket with the hole dug out
before, then mark the four fixation holes through wall-mounting bracket on the
wall
| Take down the wall-mounting bracket, then using a6mm hand drill to make the
four fixation holes on the wall which marked before.
| Once the fixing holes were made, insert plastic wall anchors.
| Twist M3x10.5 hex socket screw into the bottom
hole of the wall-mounting bracket until the tail of which align to the edge.
Then fix the wall-mounting bracket on the wall with four ST4x20 crosshead
screws. If there is a ground wire to be connected, use M3x6 crosshead screw to
fix it on the wall- mounting bracket.
With embedded box in the wall
| Make sure all cables in the embedded box.
| Twist M3x10.5 hex socket screw into the bottom
hole of the wall-mounting bracket until the tail of which align to the edge.
Then fix the wall-mounting bracket on the wall with two M4x30 crosshead
screws. If there is a ground wire to be connected, use M3x6 crosshead
screw to fix iton the wall-mounting bracket.
Step 2: Device Mounting
| Connect the cables to device.
---|---
| Push down to fix the device securely. Tighten
M3x10.5 hex socket screw on the device with Allen wrench.
Device Wiring
Warning
When you connect a device containing a coil, such as a relay or an
electromagnetic lock, it is necessary to protect the intercom against voltage
peak while switching off the induction load. For this way of protection we
recommend a diode I 1A/200 V (included in the accessories) connected
antiparallet to the device.
Application Network Topology
Configuration
- Access basic information: After setting up network and power, enter Setting > System Info to check Account, Network,Version status.
- Access the Website: Launch a browser and type in the IP address then enter the username and password to login.(username/password: admin /admin by default)
- Account Registration: On web UI, go to the path: Account > Basic page to fill in the account information,click Submit to confirm.(Please refer to user manual for more information)
Operation
Make a call:
Enter the callee’ s number or room address, then press Dial icon to make a
audio call or press Video icon to make a video call. Press icon to hang up.
Receive a call:
Press icon to pick up the incoming call in video mode or press icon to pick up
the call in audio mode.
Unlock:
During the talk, you can press the Unlock icon on the talking interface to
unlock the door.
Monitor:
Press the Monitor icon to receive the video from the door phone or from third-
party devices.
Notice Information
Information contained in this document is believed to be accurate and reliable
at the time of printing. This document is subject to change without notice,
any update to this document can be viewed on Akuvox’ s website:
http://Awww.akuvox.com © Copyright 2022 Akuvox Ltd. All rights reserved.
AKUVOX (XIAMEN) NETWORKS CO., LTD.
Addr: 10/F, NO.56 GUANRI ROAD, SOFTWARE PARK II, XIAMEN 361009, CHINA
www.akuvox.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>