muRata LBEE5ZZ1XL Wi-Fi Module User Manual
- June 9, 2024
- muRata
Table of Contents
muRata LBEE5ZZ1XL Wi-Fi Module
Model Name: LBEE5ZZ1XL
FCC ID: VPYLBEE5ZZ1XL
Since this module is not sold to general end users directly, there is no user
manual of module.
For the details about this module, please refer to the specification sheet of
module.
This module should be installed in the host device according to the interface
specification (installation procedure)
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the end user’s manual of
the end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as shown in User manual.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC CAUTION Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
This device complies with below part 15 of the FCC Rules. Part 15 Subpart C
Part 15 Subpart E
Since there is no space which indicates FCC ID on this module, FCC ID is indicated in a manual. If the FCC ID is not visible when the module is installed inside another device, then the module is installed must also display a label referring to the enclosed module.
Antenna list.
Part number
|
Vendor
| Peak Gain(dBi)|
Type
|
Connector
---|---|---|---|---
2.4GHz| 5GHz
146153| Molex| 3.2| 4.25| Dipole| U.FL
The following information must be indicated on the host device of this module.
Contains Transmitter Module FCC ID: VPYLBEE5ZZ1XL or Contains FCC ID: VPYLBEE5ZZ1XL
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
*If it is difficult to describe this statement on the host device due to the size,
please describe in the user’s manual and also either describe on the device
packaging or on a removable label attached to the device.
The following statements must be described on the user manual of the host device of this module;
FCC CAUTION Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
When installing it in a mobile equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.
When installing it in a portable equipment.
It is necessary to take a SAR test with your set mounting this module. Class II permissive change application is necessary using the SAR report. Please contact Murata.
Note)
Portable equipment : Equipment for which the spaces between human body and
antenna are used within 20cm. Mobile equipment : Equipment used at position in
which the spaces between human body and antenna exceeded 20cm.
FCC
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is the passed down
through the MAC, through the digital and analog baseband, and finally to the
RF chip. Several special packets are initiated by the MAC. These are the only
ways the digital baseband portion will turn on the RF transmitter, which it
then turns off at the end of the packet. Therefore, the transmitter will be on
only while one of the aforementioned packets is being transmitted. In other
words, this device automatically discontinue transmission in case of either
absence of information to transmit or operational failure.
Frequency Tolerance: ±20 ppm
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>