muRata LB2GT LoRa Module User Manual

June 1, 2024
muRata

muRata LB2GT LoRa Module

muRata-LB2GT-LoRa-Module-product

Product Information

Specifications

  • Part Number: LBAA0XV2GT
  • FCC ID : VPYLB2GT
  • IC: 772C-LB2GT
  • Antenna types:
    • 2.4GHz Antenna: ANT-DB1-RAF-RPS (Peak gain 2.5dBi)
    • Sub-GHz Antenna: 001-0002 (Peak gain 2.0dBi)
  • RP-SMA connector for Sub-GHz and 2.4GHz antennas
  • Dimensions:
    • Sub-GHz antenna connector: Length – 18.55 mm, Width – 0.34 mm
    • 2.4GHz antenna connector: Length – 24.12 mm, Width – 0.34 mm

FAQ

  • Q: Can I use antennas other than the recommended ones with this module?
    • A: No, using antennas with gains exceeding the specified maximum gain is strictly prohibited for this device.
  • Q: What is the minimum distance recommended between the device and the body during operation?
    • A: A minimum distance of 20cm should be maintained between the radiator of the device and your body.

LBAA0XV2GT has been FCC/ISED certified as Single Modular Approval with the following IDs.

muRata-LB2GT-LoRa-Module-fig-1

The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end user has no manual instruction to remove or install module. Therefore, the final host product must be submitted to Murata for confirmation that the installation for the module into the host is in compliance with regulations of FCC and IC Canada. Specially, if an antenna other than the model documented in the Filing is used, a Class 2 Permissive Change must be filed with the FCC. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

This module has been approved by FCC to operate with the antenna types with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. The following antenna has been certified in combination with the module. Refer to the next pages for the antenna application guidance.

  • Whip antenna by Linx with peak gains as 2.5dBi for 2.4GHz ISM band
  • Whip antenna by TE with peak gain as 2.0dBi for the sub GHz band

Antenna Application Guidance

muRata-LB2GT-LoRa-Module-fig-2

muRata-LB2GT-LoRa-Module-fig-3

FCC STATEMENT

Please take attention that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC/IC RSS 102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body. When the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording ”Contains transmitter module FCC ID: VPYLB2GT” or “Contains FCC ID: VPYLB2GT”.

When the module is installed inside another device, the user manual of this device must contain below warning statements:

  1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  2. This device may not cause harmful interference.
  3. This device must accept any interference received, including interference that may cause undesired operation.
  4. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product.
The host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.

The end user manual shall include all required regulatory information/warning as shown in this manual, include:

  • This product must be installed and operated with a minimum distance of 20 cm between the radiator and user body.

IC Statements

This device complies with Industry Canada licence exempt RSS standard(s). Operation is subject to the following two conditions:

  1. this device may not cause interference.
  2. this device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power ( e.i.r.p .) is not more than that necessary for successful Communication.

This equipment complies with FCC/IC RSS 102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

When the Industry Canada certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can be use wording ”Contains transmitter module IC: 772C LB2GT” or “Contains IC: 772C LB2GT”.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals