muRata JS-0989 Type2AB UWB Module EVB User Manual

June 1, 2024
muRata

Type2AB UWB Module
EVB User Manual
(Rev5.1)muRata JS 0989 Type2AB UWB Module EVB 7th March 2024
UWB Section, muRata/SyChip

JS-0989 Type2AB UWB Module EVB

muRata JS 0989 Type2AB UWB Module EVB - Fig

Introduction

This document provides basic information about Murata Type2AB EVB, mainly including hardware setting and related documents list.

  • About this document
    There are two main versions of Type2AB EVB, the latest one is Rev4.0 (PCB version: JS-1055), old one is Rev3.0 (PCB version: JS-0989), the main difference of two EVB versions is antenna design.
    The legacy Rev3.0 JS-0989 EVB is EOL and will no longer be provided to customers. However, considering that some users may still be using them, we retain the description of the old EVB in this document.

Type2AB Module EVB Block Diagram

muRata JS 0989 Type2AB UWB Module EVB - Diagram

Tyep2AB JS-0989 EVB Description

muRata JS 0989 Type2AB UWB Module EVB - Description

  • Antenna assembly for JS-0989muRata JS 0989 Type2AB UWB Module EVB - assembly Type2AB JS-1055 EVB Description
  • PCB antenna is used for JS-1055muRata JS 0989 Type2AB UWB Module EVB - antenna

Getting Started With Type2AB Module EVB

  1. Make sure the power supply jumper setting is the same as the picture below. If you plan to choose a different power supply method, pleaser refer to page 10 ~13 for the power supply options.

  2. Connect EVB to PC via USB interface J14 and check if the COM port appeared on Device Manager correctly. The COM port number, e.g. COM19, may vary depending on the actual environment.
    If the COM port doesn’t appear correctly, please download the virtual COM port driver from the link below and reinstall it properly.
    FTDI VCP driver link: https://ftdichip.com/drivers/vcp-drivers/

  3. Open Serial port tool on PC. Set the serial parameter as below.
    Baud rate = 115200
    Data = 8
    Parity = None
    Stop = 1
    Flow control = None
    Press reset button, if +EVENT=0,0,0 appear on serial tool, it will be indicated the EVB work correctly.

  4. The default preprogrammed firmware in Type2AB EVB is TestFW (v0.6.0).
    It’s mainly used for UWB RF testing and BLE function testing. Please refer to [1] for more details about TestFW.
    Please visit myMurata* Type2AB Document site and Software site for more references and firmware.
    Refer to [2] for details on how to upgrade the firmware.
    Refer to [3] for how to evaluate UWB ranging functions using the demo firmware.
    Refer to [4] for how to build the demo firmware with SDK and patch file.

*Note: registration is required to access myMurata Type2AB Document site and Software site.
Please refer to myMurata Access Guide for details.

Appendixes

Power supply option1 – 3.0V DC

  • Same configuration for JS-0989 and JS-1055muRata JS 0989 Type2AB UWB Module EVB - configurationPower supply option2 –5V via USB interface J14
  • Same configuration for JS-0989 and JS-1055muRata JS 0989 Type2AB UWB Module EVB - configurationPower supply option3 –5V via USB interface J6
  • Same configuration for JS-0989 and JS-1055muRata JS 0989 Type2AB UWB Module EVB - configuration 2nRF52840 pin configuration
  • EVB used PINs
    nRF52840 Pin| Function| Connection| Note
    ---|---|---|---
    P0.07| 2AB UART TX| UART to USB IC FT232RL| main UART for communication
    P0.08| 2AB UART RX
    P0.11| 2AB UART CTS
    P0.12| 2AB UART RTS
    P0.18| nRESET| reset button|
    P0.30| button| button|
    P0.28| LED1| LED1|
    P0.21| LED2| LED2|
    USB D+| USB D+| USB connector| Depend on FW
    USB D-| USB D-
  • PIN assignment for GPIO connectorsmuRata JS 0989 Type2AB UWB Module EVB - connectors Note: please refer to [5] and [6] for more details.

J-Link connections for flashing firmware
Note:

  1. Please make sure the module is powered on during FW programming . Refer to page 10-12 for the power supply options.
  2. Please refer to [1] for details on how to upgrade firmware using J-link

muRata JS 0989 Type2AB UWB Module EVB - flashing

References

References:

  1. S10210-SP-Type2AB_Test_Firmware_Specification_v0.6.0.pdf
  2. Type2AB_Firmware_Upgrade_Guide_V0.2.1.pdf
  3. S10286-Murata-QSG-Type2AB_UCI_CLI_FW_Quick_Start_Guide_Rev1.3-20240202.pdf
  4. S10285-QSG-Type2AB_DW3-QM33_SDK_Patch_Quick_Start_Guide-V0.1.2-20240202.pdf
  5. JS-1055_2AB_EVB_Schematic
  6. Application Note_Type2AB_Hardware Design Guide RevE

Revision History

Revision Date Description
V1.0 9/4/2020 Initial release
V2.0 6/9/2021 Update EVB picture for PCB JS-0969
V3.0 10/9/2021 Update EVB picture for PCB JS-0989
V4.0 2/14/2022 Update single antenna assembly direction
V5.0 9/23/2022 Update EVB picture for PCB JS-1055 (with PCB antenna)
V5.1 3/7/2024 • Update some information on page 8 and page9.

• Add references on page15.
• Add J-Link connections for flashing FW on page14
• Adjust the order of sections.

Copyright © Murata Manufacturing Co., Ltd.
All rights reserved.
07 March 2024

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals