KICHLER 49945BKTLED River Path 1-Light 17.5-Inch Textured Black Integrated Outdoor Wall Light Installation Guide

KICHLER 49945BKTLED River Path 1-Light 17.5-Inch Textured Black

Integrated Outdoor Wall Light

Fixture Diagram

• [A] Mounting Plate
• B Outlet Box Strap
• C Mounting Screws
• [D] Backpan
• [E] Mounting Screws
• [F] Glass Frame
• [G] Frame Screws
• [H] Glass
• [I] Decorative Screws
• [J] Decorative Nut

CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING:
This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.

CLEANING

Always be certain that electric current is turned off before cleaning. Only a damp cloth should be used. Harsh cleaning products may damage the finish.

Installation Instructions

INSTALLATION

• Read and understand all instructions and illustrations completely before proceeding with assembly and installation of fixture.
• If you have any doubts about how to install this fixture, or if the fixture fails to operate completely, please contact a qualified electrician.
• All parts must be used as indicated in the instructions. Do not substitute any parts, leave parts out, or use any parts that are worn or broken. Failure to obey this instruction could invalidate the UL listing, C.S.A. certification, and/or ETL listing of this fixture.
• Fixture is to be connected to a single branch circuit.
• Mounting surface should be clean, dry, flat and 1/4” larger than the fixture housing surface.

INSTRUCTIONS:

1. Attach the mounting plate[A] to the outlet box[B] with supplied strap mounting screws[C]. NOTE: The mounting strap must be mounted with the fixture mounting flanges on the side.

Installation Instructions (continued)

Grounding instructions: (See Illus. a or b).

• On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
• On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap. If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector (Not provided). After following the above steps. Never connect ground wire to black or white power supply wires.

1. Make wire connections. Reference chart below for correct connections and wire accordingly.
   Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
   ---|---
   Black| White
   Parallel cord (round & smooth)| Parallel cord (square & ridged)
   Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
   Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
   *Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)|

Neutral Wire

2. Carefully push wire connections back into outlet box making sure all connections remain secure.

3. Secure the backpan[D] to the mounting plate with the supplied mounting screws[E]. Make sure wires do not get pinched.

4. Slide the glass frame[F] over backpan and secure in place by using frame screws[G].

5. Slide glass[H] into glass frame and line up mounting holes.

6. Secure glass to glass frame using decorative screw[I] and decorative nut[J].
   INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/OR IN WET LOCATIONS.

7. Mounting surface should be clean, dry, flat and 1/4” larger that the backpan on all sides. Any gaps between the mounting surface and backpan exceeding 3/16” should be corrected as required.

8. With silicone caulk, caulk completely around where the backpan meets the wall surface to prevent water from seeping into outlet box. The bottom of the backpan should be left un-caulked.

9. Place the glass frame over the backpan and secure with the screws provided.

10. With silicone caulk, caulk the top only of the glass frame where it meets the wall surface. The sides and bottom need no caulking.

FCC Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

We’re here to help866-558-5706

Hrs: M-F 9am to 5pm EST

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>