FEIT Electric SYW-PLUG3WIFI Triple Outlet Outdoor Smart Plug Installation Guide
- June 1, 2024
- Feit Electric
Table of Contents
FEIT Electric SYW-PLUG3WIFI Triple Outlet Outdoor Smart Plug
Specifications
- Electrical Ratings: 125VAC, 60Hz
- Max. Resistive Load: 15A, 1875W
- Max. Tungsten Load: 8A, 1000W
- Wi-Fi Compatibility: 2.4GHz networks
OVERVIEW
- Supplier’s Declaration of Conformity: 47 CFR§2.1077
- Compliance Information Responsible Party: Feit Electric Company 4901 Gregg Road, Pico Rivera, CA 90660, USA 562-463-2852
- ELECTRICAL RATINGS: 125VAC, 60Hz
- 15A,Max. Resistive: 1875W
- 8A,Max. Tungsten: 1000W
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
IMPORTANT SAFETY INSTRUCTIONS
- When using electrical products, basic precautions should always be followed.
- THIS OUTDOOR SMART PLUG IS A“GROUNDED” DEVICE The male plug contains a ground pin and is only intended for use with a three-pronged grounded outlet.
- DO NOT ATTACH A DEVICE THAT EXCEEDS THE UNIT RATINGS.
WARNING : THE OUTLET MUST BE MOUNTED IN A VERTICAL POSITION WITH OUTLETS
FACING DOWNWARD AND BE AT LEAST 55 IN. (1.4M) ABOVE GROUND LEVEL.
CAUTION: RISK OF ELECTRIC SHOCK. GROUNDING CONTINUITY MUST BE MAINTAINED.
TROUBLESHOOTING TIPS
If you are having difficulty connecting:
-
Make sure the Wi-Fi network is a 2.4 GHz network. Outdoor Smart Plug will not connect to a 5 GHz network. Test your Wi-Fi network with other devices such as your phone to make sure it is operating properly.
-
The Wi-Fi connection may not have good coverage during setup. Try moving the Outdoor Smart Plug closer to your Wi-Fi router.
Your Wi-Fi network password is case-sensitive, make sure you are entering it correctly. -
Devices plugged into your Outdoor Smart Plug must be ON to be controlled via the mobile app.
Please also check the App User Guide for more information
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This device should be installed and operated with a
minimum distance of 20cm between the radiator and your body. This device
complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, under part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates,uses, and can radiate radio
frequency energy and, if not installed and used by the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
f this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the chiseler or an experienced radio/TV technician for help.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to generate the equipment
IC Caution:
- Radio Standards Specification RSS-Gen, issue 5
- This device contains license-exempt transmitters)/receivers) that comply with
- Innovation, Science and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF exposure statement:
The equipment complies with the IC Radiation exposure limit set forth for
uncontrolled environments. This equipment should be installed and operated
with a minimum distance of 20cm between the radiator and the vour body.
Getting Started
-
Download the Feit Electric app on your smart device
-
Plug in your Outdoor Smart Plug
Plug the Smart Plug into an outdoor-rated GFCl receptacle with an appropriate outdoor cover. WARNING: These products may represent a possible shock or fire hazard if improperly installed or attached in any way.
Products should be installed by the owner’s manual, current electrical codes, and/or the current National Electric Code (NEC).
The indicator light must be rapidly blinking to connect. I not already blinking, press and hold the power button for five seconds -
Turn on Bluetooth and open the Feit Electric app to complete the setup.
Tap Add Device or the +sign. The device name(s) will pop up on the Feit app. Tap on Go to add, then select the device to add.
You will be prompted to enter your Wi-Fi network name and password.
Multiple devices can be added using Simple pairing.
Alternative set up options and help instructions are available in the Feit Electric app Be sure to connect to a 2.4 GHz Wi-Fi network that covers your installation location -
Plug your device into the Outdoor Smart Plug
Ensure your device is switched to the ON position and plug it into the Outdoor Smart Plug
FINISHING INSTALLATION
- Once you’re up and running, secure the Outdoor Smart Plug to wall by inserting a screw (not included)through the strain relief tab.
- Make sure to tightly cap the Outdoor Smart Plugs when not in use.
(Optional)Connect to Google Assistant or Alexa using the in App guide
Need Help
- Thank you for your purchase
- Questions, comments or feedback?
- We’d love to hear from you.
- Visit feit.com/help for support or connect with us:
FOR DETAILED INSTRUCTIONS ON SMART FEATURES SEE THE APP USER GUIDE.
FAQ
- Q: What Wi-Fi networks are supported by the smart plug?
- A: The smart plug only supports 2.4GHz Wi-Fi networks.
- Q: How do I reset the smart plug?
- A: To reset the smart plug, press and hold the power button for 10 seconds until the indicator light blinks rapidly.
FEIT ELECTRIC COMPANY
-
ADDRESS: Pico Rivera,CA,USA
-
TEL: 1-866-326-2852
-
FAX: (562)908-6360
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>