FEIT ELECTRIC REV009 Adjustable White Linear LED Canless Recessed Downlight Instruction Manual

FEIT ELECTRIC REV009 Adjustable White Linear LED Canless Recessed

Downlight

Product Information

Specifications

• Model: REV009
• Manufacturer: Feit Electric Company
• Location: Pico Rivera, CA
• Website: www.feit.com

Product Usage Instructions

Installation

1. Locate a suitable area to install the product.
2. Ensure the product is powered off before installation.
3. Follow the provided installation guide for step-by-step instructions.
4. Securely mount the product in place using the recommended tools.

Operation

1. Power on the product using the designated switch or button.
2. Adjust settings as needed according to the user manual.
3. Monitor the product for any irregularities during operation.
4. Power off the product when not in use to conserve energy.

Maintenance

1. Regularly clean the product using a soft, dry cloth.
2. Avoid using harsh chemicals or solvents for cleaning.
3. Inspect the product for any signs of damage and address promptly.
4. Refer to the maintenance section of the user manual for detailed instructions.

Frequently Asked Questions (FAQ)

• Q: How do I contact Feit Electric Company for support?
  A: You can reach out to Feit Electric Company via the contact information provided on their website.

• Q: Can I use this product outdoors?
  A: Refer to the product specifications to determine if it is suitable for outdoor use. Avoid exposing the product to elements it is not designed for.

• Q: What should I do if the product malfunctions?
  A: In case of malfunction, refer to the troubleshooting section of the user manual. If issues persist, contact customer support for assistance.

IMPORTANT SAFETY INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, operate or install this product. This product must be installed by any applicable installation code(s) by a qualified electrician or person familiar with the construction and operation of the product and the hazards involved.

1. WARNING: RISK OF SHOCK. House electric current can cause painful shock or serious injury unless handled properly. For your safety, always remember to:
2. A. Ground the fixture to avoid potential electric shocks and to ensure reliable starting.
3. B. Double-check all connections to be sure they are tight and correct.
4. C. Wear rubber-soled shoes and work on a sturdy ladder.
5. This fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also designed to be installed by local electrical codes. If you are unsure about your wiring, consult a qualified electrician or a local electrical inspector and check your local electrical code.
6. WARNING : RISK OF CUTS. Some metal parts in the fixture may have sharp edges. To prevent cuts and scrapes, wear gloves when handling the parts.
7. Account for small parts and destroy packing material, as these may be hazardous to children.
8. Risk of Fire – MINIMUM 90°C SUPPLY CONDUCTORS. If uncertain, consult an electrician.
9. This device is not intended for use with emergency exits.
10. Risk of pinching – Do not place hands under springs during removal of the downlight.

VAPOR BARRIER MUST BE SUITABLE FOR 90 °C.
FOR USE IN NON-FIRE-RATED INSTALLATIONS ONLY.

NOTICE:

• All electrical connections must be by local and National Electrical Code (N.E.C) standards. If you are unfamiliar with proper electrical wiring connections, obtain the services of a qualified electrician.
• Remove the fixture and the mounting package from the box to make sure that no parts are missing by referencing the illustrations on the installation instructions.

CAUTION : Tum off the main power at the circuit breaker before installing the fixture in order to prevent possible shock

Supplier’s Declaration of Conformity:
47 CFR § 2.1077 Compliance Information

Responsible Party:
Feit Electric Company 4901 Gregg Road, Pico Rivera, CA 90660, USA

Unique Identifier:
FEIT ITEM# LEDR12XT/6WYCA

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

WARRANTY

This product is warrantied to be free from defects in workmanship and materials for up to five years from the date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, visit feit.com/contact-us for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province to province.

PACKAGE CONTENTS

Before beginning installation of this product, make sure all parts are present. Compare parts with the package contents list and diagram. If any part is missing or damaged, do not attempt to assemble, install or operate this product

Tools Required {Not Included)

• Screwdriver
• Drywall saw (recommended)
• Goggles
• Gloves
• Ladder

Package Components

PRODUCT ELECTRICAL RATINGS

The foam insert between the trim and ceiling of this panel will create an air- tight seal and is required for the ASTM Air Tight Certification. Suitable for Type IC.

CHOOSE A WHITE COLOR SETTING

NOTICE : The toggle switch is located on the power supply box.

CHOOSE YOUR FAVORITE WHITE COLOR TEMPERATURE

• When the slide switch is set to SW (Soft White), the color temperature is set at 2700K.
• When the slide switch is set to BW (Bright White), the color temperature is set at 3000K.
• When the slide switch is set to NW (Neutral White), the color temperature is set at 3500K.
• When the slide switch is set to CW (Cool White), the color temperature is set at 4000K.
• When the slide switch is set to DL (Daylight), the color temperature is set at 5000K.

ADJUST YOUR LIGHT COLOR ANYTIME WITH A REGULAR WALL LIGHT SWITCH

• Set the slide switch on the power supply box to SWITCH.
• Toggle your light switch ON and OFF within 0.5-2 seconds to cycle through the five different white color temperatures.
• If the fixture is left OFF for over 10 seconds and then turned ON, the fixture remembers the last white colour temperature selected and displays that colour when turned on again.
• The reset function is used when using multiple color-selectable lighting products operating from the same light switch. If multiple fixtures are not displaying the same colour at the same time, the fixtures must be RESET using your existing light switch. From the ON position toggle the wall switch ON and OFF seven times, pausing in the ON position for 1 second each time.

PRE-INSTALLATION REVIEW

1. Turn the power OFF from the breaker panel before starting installation.
2. Locate a suitable location for the fixture and cut the correctly sized hole in the drywall or ceiling tile (for a suspended T-Bar type ceiling).
3. Know the location of your joist before making any cuts.
4. Run electrical wire from home to the power supply box; use NM cable or Flexible Metal Conduit Cable.
5. Use the slide switch to choose a preferred color temperature before installing (2700K, 3000K, 3500K, 4000K, 5000K) or use Switch mode (SW) to cycle through the different color temperatures

INSTALLATION INSTRUCTIONS FOR RECESSED HOUSING

1. Identify the number of downlights to be installed and measure the designated locations for each fixture. Utilize the supplied cutout template to mark the precise hole positions

2. Cut a rectangular hole in the ceiling as accurately as possible using a drywall saw (not included) and the provided cutout template. Make sure the opening is not larger than the outer trim of light
   NOTE : Before cutting, ensure that the hole does not impinge on joists, pipework, cable or other building services

3. Gently extract the knockout from the Power Supply Box (A) using a screwdriver or punch driver

4. Open the Power Supply Box (A) cover. Feed the supply wire into the knockout hole using a 3/8 in. clamp connector (not included). Using Quick Connectors (C), connect the 120V line (black) wire to the black wire, connect the neutral (white) wire to the white wire, and connect the ground (green) wire to the green wire. This power supply box needs to be grounded. Wires inserted into the quick connectors must meet the “Wire Guage and Strip Length Requirements
   NOTE : For the best connection, use solid wire or tin-bonded stranded wire. If using stranded wire, we recommend using wire nuts (not included).

5. After inserting the supply wire into the Quick Connectors (C), double-check the connection by following these simple tests:

6. Hold the quick connector with one hand and with the other hand pull at the connected wires to ensure proper wire connection.

7. Ensure a sufficient amount of wire is visible through the clear shell for visual verification.

8. Reconnect the Power Supply Box to the downlight. To ensure proper connection, the arrows on the cable adapters must be facing each other and the colour label on each end should match. Screw on the fastener to secure the connection.

9. Hold the spring clips against the Downlight (B) and gently guide into the ceiling until the clips snap into place. The fixture should be flush with the ceiling.

10. Restore the power at the breaker panel.

WIRE GUAGE AND STRIP LENGTH REQUIREMENTS

NOTE : If the jacket of the cable is not in the Wago connector ensure the strip length is correct and/or verify the wire is fully inserted

END TO END CONNECTION INSTRUCTIONS

1. Identify the number of downlight fixtures (B) to be installed and the polarity of the magnets on each end.
2. NOTE : Ensure to align the magnets correctly by following the LJ South (S) and North (N) polarity labels for proper linkage.
3. NOTE : End-to-end connection provides limitless customization LJ possibilities with 1ft, 3ft, and comer downlights.
4. NOTE , Downl~hts smd separately
5. Detach the endcap trim from the downlight fixture (B) by removing the two screws.
6. NOTE : Do not remove the clear rubber gasket at the end of LJ the fixture (B).
7. Cut the overhanging gasket from the downlight fixture (B).
8. Slide the white seam cover (E) over the end of the downlight fixture (B).
9. Connect the ends of the downlight fixtures (B).
10. Slide the white seam cover (E) towards the linking point of the two downlight fixtures (B) to cover the seam.

FEIT ELECTRIC COMPANY | PICO RIVERA, CA | www.feit.com
To order contact FEIT ELECTRIC COMPANY
Http : www.feit.com
Email : info@feit.com

References

• Energy Saving Light Bulbs, Light Fixtures | CFL, LED & More

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>