FEIT Electric T9 Plug and Play Linear Lamp Installation Guide
- June 3, 2024
- Feit Electric
Table of Contents
FEIT Electric T9 Plug and Play Linear Lamp Installation Guide
Safety Information
PLEASE READ THESE INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION.
THIS LAMP IS INTENDED TO WORK WITH THE EXISTING MAGNETIC 0R ELECTRONIC BALLAST
IN YOUR LIGHTING FIXTURE. THIS IS A PLUG AND PLAY LAMP, NO ELECTRICAL
MODIFICATIONS ARE NEEDED.
This LED tube is intended to replace fluorescent tube lamps with ANSI
designation FC12 with G10q base.
This product may not be compatible with all ballasts. For more information
about ballast compatibility please visit www.FEIT.C0M.
WARNING: Check the luminaire (fixture) carefully before installing the lamp. Ensure the electrical lamp holders (sockets) are not damaged and will make firm contact with the lamp pins.
CAUTION: Risk of fire – If lamp or luminaire exhibit abnormal operation
(buzzing, flickering, minimal or no light, etc.), immediately turn off power
and contact us for more information.
CAUTION: Risk of fire – Suitable for damp locations. Do not use with
Simmers. Do not touch lamp pins to the metal housing when installing.
WARNING: Do not install this in a pre-heat luminaire (fixture), often
with external starters.
-
Always follow basic safety precautions to reduce the risk of fire, electric shock and personal injury.
-
WARNING: RISK OF SHOCK: House electric current can cause painful shock or serious injury unless handed properly. For your safety, always remember to:
A. Turn OFF the power supply at the fuse or circuit breaker box before you install the lamp.
B. Ensure the fixture is grounded to avoid potential electric shock and to ensure reliable starting.
C. Wear rubber sole shoes and work on a sturdy ladder
D. Do not touch with wet hands.
E. This lamp is not intended for use with emergency exits or emergency lights. -
This lamp is designed for use in a circuit protected by a fuse or circuit breaker. It is also designed to be installed in accordance with local electrical codes. If you are unsure about your wiring, consult a qualified electrician or local electrical inspector, and check your local electrical code.
-
Avoid looking directly into the lamp.
-
WARNING: RISK OF CUTS: To prevent wiring damage, abrasion or cuts, do not expose wiring to edges of sheet metal or other sharp objects and wear gloves.
-
Account for small parts and destroy packaging material, as these may be hazardous to children.
SAVE THESE INSTRUCTIONS
We appreciate the trust and confidence you have placed in Feit Electric
through the purchase of this T9 Linear Lamp.
We strive to continually create quality products designed to enhance your
home. Visit us online to see our full line of products available for your home
improvement needs.
Thank you for choosing Feit Electric.
Direct Replacement/Plug & Play Installation Instructions (Type A)
-
STEP 1.
Turn- off power before installation. -
STEP 2.
Remove the existing lamp from the support clips to the fixture. -
STEP 3.
Disconnect the socket from the existing lamp. -
STEP4.
Connect the fixture socket to the new LED Lamp. -
STEP 5.
Push the lamp into the support clips. -
STEP 6.
Turn-on power and enjoy new Feit LED Tube.
Limited Warranty
This product is warrantied to be free ftom defects in workmanship and
materials for up IO 5 years from date of purchase. If the product fails within
the warranty period, please contact Feit Electric at info@feit.com,
visitfeit.com/contact-us for intinctions on replacement or refund.
REPLACEMENT 0R REFUND IS YOUR SOLE REMEDY. EXCEPT TO TUE EXTENT PROHIBITED
BYAPPLICABLELAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE
DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces
do not allow the exclusion of incidental or consequential damages, so the
above Imitation or exclusion may not apply to you. This warranty gives you
specific legal right, arid you may also have other rights
which vary from state to state or province to province.
FCC STATEMENT
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses arid can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
pai1icular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different 1tom that IO which
the receiver is connected.
Consult the dealer or an experienced radial/TV technician for help.
Any changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
THIS PRODUCT MAY NOT BE COMPATIBLE WITH ALL BALLASTS.
FOR MORE INFORMATION ABOUT BALLAST COMPATIBILITY PLEASE VISIT
WWW.FEIT.C0M
Supplier’s Declaration of Conformity:
47 CFR § 2.1077 Compliance Information
Responsible Party: Feit Electric Company
4901 Gregg Road, Pico Rivera, CA 90660, USA
Customer Support
Thank you for your purchase. Questions, comments or feedback?
We’d love to hear from you.
Visit feit.com/help for support.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>