FEIT electric GLP12ADJS 12 Inch 12W Full Spectrum LED Grow Light User Guide

FEIT electric GLP12ADJS 12 Inch 12W Full Spectrum LED Grow Light

Questions, problems, missing parts? Before returning to the store, visit feit.com/help for further assistance

THANK YOU
We appreciate the trust and confidence you have placed in Feit Electric through the purchase of this LED utility fixture.
We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Feit Electric.

Safety Information

For your safety, always remember to

• Tum off the power supply at the fuse or circuit breaker box before you install the fixture.

• Double-check all connections to be sure they are tight and correct.

• Wear rubber-soled shoes and work on a sturdy wooden ladder.

• Account for small parts and destroy packing material, as these may be hazardous to children.

  • NOTE: This fixture is designed for use in a circuit protected by LJ a fuse or circuit breaker. It is also designed to be installed in accordance with local electrical codes. If you are unsure about your wiring, consult a qualified electrician or local electrical inspector, and check your local electrical code.

  • WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance

  • CAUTION: Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.

  • NOTICE: All connections must be in accordance with local electrical standards and the National Electrical Code (N.E.C.) or Canadian Electrical Code (C.E.C) as appropriate.
    Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions.

  • IMPORTANT: This fixture is intended to be only installed ? directly beneath a ceiling-mounted receptacle.

  • CAUTION, IMPORTANT SAFTEY INSTRUCTIONS: This portable light-emitting-diode (LED) luminaire has a polarized plug (One blade is wider than the other) as a feature to reduce risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless the plug can be fully inserted. Do not alter the plug.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. CAN ICES-005 (B).

Supplier’s Declaration of Conformity: 47 CFR § 2.1077 Compliance Information Responsible Party:
Feit Electric Company
4901 Gregg Road,
Pico Rivera, CA 90660, USA
562-463-2852
Unique Identifier:
GLP12ADJS/RF/1 OW/LED

Limited Warranty

This product is warrantied to be free from defects in workmanship and materials for up to 5 years from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, visit feit.com/contact-us or call 1-866-326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

Pre-Installation

NOTE: Hardware images are for illustration D purposes only. Actual product size may vary.

TOOLS REQUIRED

PACKAGE CONTENTS

Hanging Installation

Turning off the power
□ Turn the power OFF at the switch, fusebox, or circuit breaker.

Attaching the Screw Hooks Screws to a drywall ceiling

• Mark the location for the wall anchors (CC). The spacing between the wall anchors (CC) should be 11114 inches.
• Drill holes for anchors.
• Insert anchors (CC) into holes.
• Screw in the screw hooks (GG) into the wall anchors (CC).
• For wood ceilings, screw in the screw hooks (GG) directly into the wood ceiling.

Installing the Hanging Cables to the V-hooks

• Place the V-hook (HH) through the loop of the hanging cables (FF).
• Insert the V-hook into the rectangular slots on the top of the fixture.

Attaching the Hanging Cables
Attach the hanging cables (FF) onto the screw hooks (GG) and plug in the power cord (DD) into the grow light (AA).

Attaching the zip tie
Use the zip tie (II) to attach the power cord (DD) to the hanging cable (FF).

Turning on the power

• Plug in the grow light into wall outlet and power On by flipping the switch in On position.
• Tum the power ON at the switch, fusebox, or the circuit breaker.
• Turn the fixture ON/OFF using the provided remote.

Linking multiple fixtures (optional)

• Link units directly against each other or with 12 in. Linkable Gable (EE).
• Link up to 39 additional GLP12ADJS/RF/1 OW/LED units.

Flush Mount Installation

Turning off the power
Turn the power OFF at the switch, fusebox, or circuit breaker.

Attaching the Mounting Screws to a drywall ceiling

• Mark the location for the wall anchors (CC). The spacing between the wall anchors (CC) should be 1 O 314 inches.
• Drill holes for anchors.
• Insert anchors (CC) into holes.
• Screw in the mounting screws (BB) into the wall anchors (CC). Leave 0.1 in. gap between the ceiling and screw head as shown.
• For wood ceilings, screw in the mounting screws (BB) directly into the wood ceiling.

Installing the Fixture to the Mounting Screws

• Align the screw holes in the top of the fixture with the screw heads (BB).
• Lift up and slide to one side to secure the fixture.

Attaching the Power Cord
Plug in the power cord (DD) into the grow light (AA).

Turning on the power

• Plug in the grow light into wall outlet and power On by flipping the switch in On position.
• Tum the power ON at the switch, fusebox, or the circuit breaker.
• Turn the fixture ON/OFF using the provided remote.

Linking multiple fixtures (optional)

• Link units directly against each other or with 12 in. Linkable Gable (EE).
• Link up to 39 additional GLP12ADJS/RF/1 OW/LED units.

Mounting the remote holder

Attaching the remote holder

• Mark the location for the remote anchors (I).
• Drill holes for anchors using a drill bit.
• Insert anchors (Il) into holes.
• Install the screws (MM) into the wall anchors (lI)
• For wood ceilings, screw in the screws (MM) directly into the wood wall.
• Double-sided tape can be used in place of screws. Remove backing on tape (NN) and secure to mount (KK).

How to pair Shoplight with Remote

NOTE: The shop light must be connected to power to complete U the pairing process.

To pair your shoplight

• Using the wall switch or switch on the product, turn Off the shop light then turn it back On.
• Within the initial 30 seconds of illumination, long press any of the individual control buttons (1, 2, or 3 button) until the LED above the button blinks three times, then release button.
• To indicate a successful pairing, the shop light will blink three times.
• After successfully pairing, the shop light can be controlled by individual or master control (all button).

To unpair your shoplight:

• Using the wall switch or switch on the product, turn Off the shop light then turn it back On.
• Within the initial 30 seconds of illumination, long press the originally paired individual control button until the LED above the button blinks three times, then release button.
• To indicate a successful unpairing, the shop light will blink one time.
•  After successfully unpairing, the shop light can be paired again by following the pairing instructions.

How to Use Wireless Remote

1. Power Button
   Press the power button to turn the shop light on and off.

2. Grow Settings Buttons
   Grow setting refers to the grow stage of the plant. (Refer to the 3 growing stages on page 8.)

3. Adjustable Color Spectrum Buttons
   Switch colors to match the plants growth stage and increase productivity.

4. Timer Buttons
   Timer can be set by selecting from one of the preset options: 3H, 6H, 8H, 12H, 18H, 24H. The light will be turned Off at the selected time.

5. Auto Mode Button
   Press the Auto Mode button to repeat the timer every day at the same time.
   Example: If you want the grow lights to turn On every day at 1:00 pm and to turn Off at 9:00 pm, then you would set your timer at 1:00 pm.
   The parameters will be 8H timer and Auto mode.

6. Single Mode Button

   • Press the Single Mode button to set the timer for one-time only. Single mode will not repeat the timer the following day.
   • Example: If you want the grow lights to stay On for 12 hours for one time only. The parameters will be 12H timer and Single mode.

7. Individual Control
   By pressing 1, 2, or 3 button, you can control an individual or set of shop lights that are paired to that control number.

8. Group Control
   By pressing the All button, you can control all the shop lights that are paired to the remote.

Using the Grow Lights

Recommended Light to Plant Distance
Plant types are generally categorized into high or low light level plant categories. The PAR value of a plant light equates to the amount of light energy that a plant can absorb. The higher the PAR, the more intense the light energy a plant can absorb facilitating accelerated vegetative and/or flowering growth. Below are the plant types and recommended optimal light energy absorption distances based on this LED Grow Light:

High light plants
Tomatoes, peppers, perennials, etc.
Seedlings Stage – 6 in. through 2 weeks of vegetative stage Vegetative and/or Flowering Stage – 16-30 in.

Low light plants
Herbs and leafy greens (such as basil lettuce).
Seedlings Stage – 12 in. through 2 weeks of vegetative stage Vegetative and/or Flowering Stage – 24-30 in.

• The height is the distance between the light source to the top of the plant.
  Increase the height of the telescoping post if dry spots on the plant begin to form.
  ** Growth cycle depends on the type of plant.

Plants in Seedling Growth Stage

• The recommended growth cycle is 16 or more hours of light a day.
• Seeds typically germinate in five to 10 days given optimal conditions. You’ll know seeds have germinated as soon as you see a green plant emerging from the soil.
• The plant is now in the seedling stage. The time in this stage is two to three weeks.

Plants in Vegetative Growth Stage

• The recommended growth cycle is 18 hours of light during the vegetative growth stage. This light cycle will create an environment that mimics the photoperiod in the summer with long days. It is during the vegetative growth stage that cloning, transplanting, pruning, and bending are all initiated.
• Turn your LED grow light ON for 18 hours a day and then turn the light OFF and leave your plant in the dark for another six hours. Most plants will need four to six weeks in the vegetative cycle before reaching the flowering stage.

Plants in the Budding and Flowering Growth Stage

• Pre-flowers are the first indication that the plant is ready to move into the budding and/or flowering stage of growth.

• The pre-flowers grow at branch internodes just behind the leaf spur typically around the fourth week of vegetative growth, when the plant is six to eight weeks old.

• When you start seeing pre-flowers forming this means that the plants are ready to go into the flowering stage. You can continue to grow in the vegetative growth stage or switch to flowering at this point. The pre-flower looks like a regular female flower with white fuzzy pistils. The
  pre-flowering can take from one to two weeks.

• Wait to induce flowering until pre-flowers have appeared. Induce flowering by switching your light cycle to 12 hours of uninterrupted darkness and 12 hours of light.

Notes:

• If LED grow light is installed as a flush mount fixture under a cabinet or canopy where distance cannot be adjusted, mount at the min of 24″ distance.
• If LED grow light can be hung from a ceiling, cabinet or canopy, use the supplied hanging assembly or purchase a chain separately to adjust height of LED light to maintain the recommended distances as the plant grows.
• For taller plants including tomatoes, mounting one (1) grow light overhead and one (1) grow light as a side light on either side of the plant will provide additional supplemental light supporting fuller plant growth for a bushy plant.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>