ELAN EL-4KM-V44-18G 4×4 HDBaseT Matrix User Guide
- June 9, 2024
- ELAN
Table of Contents
ELAN EL-4KM-V44-18G 4×4 HDBaseT Matrix
Quick Reference Guide
The ELAN® 4×4 HDBaseT matrix offers unprecedented performance and value for the custom installation market. The EL-4KM-V44-18G is a HDMI 2.0 4K 60Hz 4:4:4 HDCP 2.2 matrix utilizing CSC technology to deliver HDMI, bi-directional IR and PoC up to lengths of 70m over a single CAT cable. The matrix also provides advanced features including simultaneous HDBaseT / HDMI on output 1, video down conversion on HDBaseT outputs and a web browser interface module for control and configuration of the matrix.
Panel Description
Front
❶ IR Receiver – Built in IR sensor for IR pass through
❷ Output LCD – Shows the currently selected output
❸ Output Up / Down Button – Press to adjust the selected output up or down
❹ Input Up / Down Button – Press to adjust the selected input up or down /
Press and hold Input Up to power the matrix on or off
❺ Input LCD – Shows the currently selected input
Please note: Press and hold Output Up and Input Down for 10 seconds to factory reset the matrix.
Rear
❶ IR Control Input – 3.5mm stereo connector to connect to ELAN 5V 3.5mm IR
receiver for IR control of the matrix
❷ TCP/IP – RJ45 connector for TCP/IP and Web GUI control of the matrix
❸ RS-232 – DB9 connector for RS-232 control of the matrix
❺ IR Receiver Output – 3.5mm mono connector to connect to ELAN 5V 3.5mm IR
emitter. Used for local Source control
❺ IR Receiver Input – 3.5mm stereo connector to connect to ELAN 5V 3.5mm IR
receiver or Control Processor. Used to extend IR from Matrix to HDBaseT
Outputs 1-4
❻ HDMI Inputs – Connect to source devices
❼ HDMI Output – Connect to display device
❽ HDBaseT Outputs – RJ45 HDBaseT port to connect to the HDBaseT input port of
the compatible ELAN HDBaseT receiver
❾ IEC Power Socket – Use supplied IEC power cable
RS-232 Configuration
The RS-232 port is used for configuration and control of the product, as well
as pass through of RS-232 commands to a compatible ELAN HDBaseT receiver /
matrix device.
The default RS-232 communication settings are:
Baud Rate: 57600
Data Bit: 8
Stop Bit: 1
Parity Bit: none
For a complete RS-232 command list please see the EL-4KM-V44-18G user manual – available to download from www.elancontrolsystems.com
Specifications:
Video Input Connectors: 4 x HDMI Type A, 19-pin, female
Video Output Connectors: 1 x HDMI Type A, 19-pin, female, 4 x HDBaseT™ RJ45
connectors
RS-232 Serial Port: 1 x 3-pin Phoenix conenctor
IR Input Ports: 5 x 3.5mm stereo jack
IR Output Ports: 4 x 3.5mm mono jack
Rack Mountable: 1U rack height, rack ears included
Casing Dimensions (W x H x D): 437mm x 44mm x 377mm (without feet)
Dimensions (W x H x D): 437mm x 53mm x 384mm
Shipping Weight: 6.25kg
Operating Temperature: 32°F to 104°F (-5°C to +55°C)
Storage Temperature: -4°F to 140°F (-25°C to +70°C)
Power Supply: Internal 100-240V AC 3A
HDBT Power Output: 12V DC 0.8A Per Port
Package Contents:
- 1 x EL-4KM-V44-18G
- 1 x Rack mounting kit
- 1 x Remote control
- 4 x IR emitters
- 5 x IR receivers
- 1 x RS-232 control cable
- 1 x IR control cable – 3.5mm-3.5mm cable
- 1 x Quick Reference Guide
- 4 x IEC Power cables (US, UK, EU & AU)
Certifications
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION – changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CANADA, INDUSTRY CANADA (IC) NOTICES
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other
household wastes. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please
use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmentally safe
recycling.
Main:
1 800-472-5555 – US
1 707-283-5900 – International
1 707-283-5901 – Fax
Tech Support:
techsupport@elancontrolsystems.com
Web:
elancontrolsystems.com
Information
A. Read these instructions – All the safety and operating instructions should
be read before this product is operated.
B. The apparatus should be connected to a mains socket outlet with a
protective earthing connection
C. The socket-outlet shall be installed near the equipment and shall be easily
accessible.
D. Do not ingest battery, Chemical Burn Hazard
E. This product contains a coin / button cell battery. If the coin / button
cell battery is swallowed, it can cause severe internal burns in just 2 hours
and can lead to death.
F. Keep new and used batteries away from children.
G. If the battery compartment does not close securely, stop using the product
and keep it away from children.
H. If you think batteries might have been swallowed or placed inside any part
of the body, seek immediate medical attention.
I. WARNING: Please refer the information on exterior bottom enclosure for
electrical and safety information before installing or operating the
apparatus.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>