DECKED MN5 Nissan Navarra 1503mm Bed Length Instruction Manual

DECKED MN5 Nissan Navarra 1503mm Bed Length

TOOLS REQUIRED

• 1/4″ drive ratchet
• 11mm deep socket
• 1/8″ hex wrench
• electric drill
• 11mm drill bit
• 8mm drill bit
• drill stop

Hardware box – unbagged components
(inside DECKED carton)

ASSEMBLY OVERVIEW

HEY! TORQUE BOY: READ BEFORE YOU INSTALL DECKED

1. DON’T go rogue on us, please read the instructions.
2. DON’T over tighten bolts, get em’ hand-tight.
3. DON’T use power tools.
4. If you don’t follow directions and do use power tools:
5. Set clutch at a very low setting.
6. If you blow it: Two extra threaded inserts are included in BAG PREP-EXTRA. That’s all you get, unless you call us and ask for more. The inserts will replace any stripped inserts in the tailgate ammo cans and studs or front face of the center vert at the bottle opener, but NOT THE TOP OF THE CENTER VERT, so hand tighten until snug only! You can also screw the inserts back in if dislocated. There is a straight screwdriver slot on the underside of the threaded insert.
7. Start all bolts with fingers to avoid cross-threading.
8. DON’T over tighten J-hooks during installation. Just get ’em good and snug; enough to keep the system from moving in the bed.
9. You will have leftover washers – you’re welcome.
10. Nice job if you’re still reading .

Prevent embarrassing, expletive-filled language,watch our detailed installation video or give us a call. We’re happy to help!
208.806.0251 | DECKED.COM/INSTALLVIDEO

AMMO CAN DRAIN HOLES
(TO DRILL OR NOT TO DRILL.)

• Do you use a tonneau or shell over your DECKED system?
  There is no need to drill holes, unless you leave your tonneau open in a deluge.

• Does your DECKED system live outside?
  The ammo cans will get water in them. You’ll need to drill holes in the ammo cans. There are two dimples in the bottom of each ammo can. Drill a 1/2” hole at each dimple. A smaller hole will get clogged.

PREP BED: MARK CENTER OF BED

• Use a marking pen or wax pencil to mark a centerline (blue) on the raised center bead.

PREP BED: SHIMS

• 2 WIDE SHIMS and 4 NARROW SHIMS loose in your hardware kit.
• Using the information below:
  1. Clean the bed surface where the shims will be located. Isopropyl alcohol is recommended.
  2. Remove tape film and apply shim and apply with pressure.

PREP BED: TAILGATE BRACKET

NOTE: You will need to grab a pal for this step (or have incredibly long and flexible arms).

• STEP 1: Mark holes as shown.

• STEP 2: At both mark locations, drill two 8mm holes. Seal with self-etching primer; BAG PRIMER.

• STEP 3: Install tailgate bracket; BAG PREP MN5, BAG WASHERS. IMPORTANT: Orient bracket hook side towards cab as shown.
  NOTE: Bracket must be oriented as shown.

• Repeat other side.

ASSEMBLY: CENTER VERT + CABSIDE VERT

NOTE: Perform the next few steps on a flat surface like a garage floor.

• Attach center vert to cabside vert with four bolts. Alternate to tighten; BAG S1. NOTE: We’ve provided a 3/8″ socket for the S1 bolts in your bag; BAG PREP MN5.

HELPFUL TIP: BAG S1, a.k.a “Bunker Hill,” is required for most of the steps, so keep it close! These bolts are highlighted throughout instructions in RED.

ASSEMBLY: LOOSELY ATTACH STUDS (YUP)

• LOOSELY attach studs to cabside vert with six bolts; BAG S1.

ASSEMBLY: ALIGN & TIGHTEN STUDS (YUP)

NOTE: This step ensures the studs are properly located before tightening bolts. It’s important.

• Place ammo cans to support tailgate end of deck panels.
• Lift deck panels on center vert + stud + cabside vert assembly.
• Slide studs around L-R until deck panels are seated.
• DETAIL A: Loosely secure four bolts to hold decks onto studs; BAG S1.
• Now you can securely tighten the bolts that hold the studs to the cabside vert.
• Unbolt deck from studs, remove deck panels, save bolts, remove ammo cans and set aside for later assembly.

PREP BED: MARK CABSIDE HOLES

• Temporarily place cabside vert + center vert + stud assembly in truck bed.
• DETAIL B: Make sure centerline arrow on cabside vert is aligned with your centerline mark (blue).
• DETAIL A, DETAIL C: Mark the truck bed via the pre-drilled holes in cabside vert.
• Remove assembly from truck bed.

PREP BED: DRILL CABSIDE HOLES

• Drill four 11mm holes at marked locations using a drill stop set to 6mm.
  NOTE: To resist corrosion, seal the raw metal edges of the drilled holes with the self-etching primer; BAG PRIMER.

• Install jacknut (yellow) onto jacknut wrench (orange) with 1″ placement bolt; BAG PREP MN5.
  NOTE: Do not use the slightly shorter dogpoint bolts also found in your PREP BAG.

• DETAIL A: Insert jacknut into hole. While holding jacknut wrench, tighten bolt with 3/8″ socket until jacknut is fully crimped. Remove placement bolt.

• Repeat on the remaining three holes.

INSTALL: MOUNT ASSEMBLY

• Place cabside vert + center vert + stud assembly in truck bed.
• Secure assembly using two 22mm screws and two washers; BAG PREP MN5. NOTE: These are the same bolts as the dogpoint bolts in your S1 BAG.
• Repeat other side.

INSTALL: C-CHANNELS

IMPORTANT: There is a left and right ammo can. The inside of each ammo can is marked L or R.

• Loosely place left side ammo can at tailgate corner of bed.
• Place left side C-channel on ledge of stud and ammo can with end plate cabside.
• Install nylon washer only onto 4 S1 bolts and all S2 bolts; BAG WASHERS.
• DETAIL A: Insert two bolts through C-channel into ammo can and loosely fasten with nut; BAG S2, BAG N1.
• DETAIL B: Tightly attach C-channel to stud; BAG S1.

RECOMMENDED TORQUE: Bolts in S1 and S2 BAG – 3Nm.

INSTALL: DECK HALVES

• Loosely place deck panel on side stud, center vert and ammo can.
• Shift ammo can forward, rearward, L-R, as necessary to align with fully seated deck panel.
• Loosely assemble:
  • Five or six bolts (depends on bed length – NO WASHERS) through deck panel into center vert; BAG S1.
  • Four bolts with nylon and rubber washers installed as shown through deck panel into stud; BAG S1, BAG WASHERS.
  • Eight bolts with nylon and rubber washers installed as shown through deck panel into ammo can; BAG S1, BAG WASHERS.
  • Tighten all S1 bolts.
  • Securely tighten C-channel/ammo can nuts and bolts.
• Repeat other side (making sure you don’t forget to securely tighten C-channel/ammo can nuts and bolts).
• We have included extra washers – don’t worry if you have leftovers.

DRAWERS: BRACKETS + WHEELS

• Each drawer has a left and a right bracket. Bolt brackets into place via bottom two holes in bracket with 19mm length screws. Use the 50mm length screws for the upper cabside wall hole in bracket; BAG DRAWER 1.
• Install a tube brace in each drawer with two 19mm length screws; BAG DRAWER 1, BAG DRAWER 2.
• Attach wheels onto drawer brackets with a 7/32″ hex wrench; BAG WHEELS
  NOTE: We’ve provided a hex wrench in your BAG PREP MN5.

DRAWERS: AXLE WHEELS + WEATHERSTRIPS

• Slide narrow drawer into driver side drawer cavity. NOTE: It is easier to fully install narrow drawer first.
• DETAIL A: Install two tailgate wheels onto narrow drawer axles with a 7/32″ hex wrench; BAG WHEELS.
• Repeat with wide drawer.
• DETAIL B: Install weatherstrips on top of drawer edges WITH WIPER BLADE POINTING TOWARD DRIVER. IMPORTANT: Facing the weatherstrip the wrong way will funnel water into drawer: DUH!

THE FUN STUFF: TORSION BRACE + BOTTLE OPENER

• Slide torsion brace under center vert and tailgate ammo cans.
• Loosely install:
• Two 1/2″ length bolts through upper holes in bottle opener into center vert; BAG FINAL MID.
• Align bottle opener to edges of center vert and tighten four bottle opener bolts.
• Tighten end bolts into tailgate ammo cans.

INSTALL: J-HOOKS

• Install J-hook onto tie down bracket and through the hole closest to the tailgate in ammo can; BAG J8.
• Install winged-spherical nut-washer, round side down, onto J-hook and partially tighten using your fingers only. IMPORTANT: Keep J-hook assembly loose.
• Repeat other side.
• Tighten the J-hooks, but DO NOT OVER TIGHTEN! Make sure the gap between the side wall of the bed and the deck is equal on both sides.
• Install bolt thread protectors on J-hook ends; BAG FINAL MID.

IMPORTANT: You’re almost there, so get your favorite beverage ready to crack open in the bottle opener and make a toast to your truck. When finished, immediately post a photo of your significant other, child or canine (in no order of significance – please someone show us your pet alligator) appreciating your accomplishment. Add hashtag #DECKEDUSA | @DECKEDUSA.

FINAL STEPS: THE RULER

•  Install ruler with six 1/8″ hex screws; BAG FINAL MID. Start screws with fingers to avoid cross-threading. Tighten just until snug. Overtightening will strip the inserts.

FINAL STEPS: AMMO CAN LIDS

• DETAIL A: Ammo can lids are left (marked L) and right (marked R) side specific.
• DETAIL B: Holding lid in orientation shown, insert tab on tailgate end of ammo can lid and push the cabside end of lid down to secure. Don’t be afraid to push down hard.
• Insert lock hole plugs, unless you are fitting the optional drawer locks, in which case install drawer locks now (instructions with locks); BAG FINAL MID.

DECKED 3-YEAR LIMITED WARRANTY

And now….a word from our lawyers.

DECKED LLC warrants to the original purchaser of this product that the product will be free from manufacturing defects in workmanship and materials for a period of three (3) years from the date of the original purchase. If within three (3) years from the original date of purchase this product fails due to defect in materials or workmanship, DECKED LLC will replace any defective part at its option.

The original purchaser must contact the DECKED LLC customer service team and provide a description of the defective part, including digital pictures if requested, with the original purchase documentation as validation of warranty coverage or have previously activated their warranty online.

This warranty DOES NOT cover or apply to:

• Damage to the product due to misuse, mishandling and abuse.
• Products not used in accordance with the manufacturer’s instructions or recommendations.
• Product not assembled or installed according to manufacturer’s instructions.
• Normal wear and tear.
• Undeclared damage to the system during shipping, acts of God. In addition, consequential damage and incidental damages (including lost time) such as damage to persons or property are not covered under this warranty.

REGISTER YOUR PRODUCT FOR ANY FUTURE WARRANTY NEEDS. DECKED.COM/REGISTER

Full size Drawer System: PATENT PROTECTED: US9527454-B2,
USD719905 S, US9168874 B2, CA2969118A1
Midsize Drawer System: PATENT PROTECTED: US10988087B2,
112017005448.6
DECKED Tool Box: PATENT PROTECTED: US20210062581A1
For more information on DECKED’s patents visit: DECKED.com/patents

References

• DECKED Truck Bed Storage, Tool Boxes & Truck Accessories
• How To Install A DECKED Truck Bed Storage System | DECKED Accessories
• Patents – DECKED, LLC CASES
• Register Your DECKED Truck Bed Organizer System | DECKED Accessories
• Register Your DECKED Truck Bed Organizer System | DECKED Accessories
• Register Your DECKED Truck Bed Organizer System | DECKED Accessories

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>