DEWERT OKIN RF426B-16 RF Touchline Remote Control Instructions
- June 12, 2024
- DEWERT OKIN
Table of Contents
Issue Department : Bedding Division
System Instruction
Instruction of RF426B
Date : 2023-06-19
Edition : 1.0
Instruction of RF426B-16
Figure 1 button of remote
Item
1.1 Child Lock 16
Double click the Child Lock button lock or unlock the remote.
1.2 Bed lamp 6
Click the bed lamp button to open or shut the light under the bed.
1.3 TV 12
Click the TV button, the bed moves to TV position, press and hold TV button
for 5s, until backlight flashes, the control set the current position as TV
position.
1.4 Ligth l3
Click the light button to open or shut the light in front of the remote.
1.5 MUSIC 14
Click the music button, the bed moves to music position, press and hold TV
button for 5s, until backlight flashes, the control set the current position
as music position.
1.6 LUMBAR UP 4
Press and hold LUMBAR UP button, Lumbar actuator moves out, stop when
released.
1.7 LUMBAR DOWN 5
Press and hold LUMBAR DOWN button, Lumbar actuator moves in, stop when
released.
1.8 HEAD UP 7
Press and hold HEAD UP button, head actuator moves out, stop when released.
1.9HEAD DOWN 8
Press and hold HEAD DOWN button, head actuator moves in, stop when released.
1.10 FOOT UP 9
Press and hold FOOT UP button,foot actuator moves out, stop when released.
1.11 FOOT DOWN 10
Press and hold FOOT DOWN button, foot actuator moves in, stop when released.
1.12 ZG 11
Click the ZG button, the bed moves to zeroG position, press and hold zeroG
button for 5s, until backlight flashes, the control set the current position
as zeroG position
1.13 HEAD MASSAGE 1
Click the HEAD MASSAGE button, head massage motor switches massage intensity,
massage intensity switches among 0-1-2-
1.14 MASSAGE time 3
Click the MASSAGE MODEL button to change the massage time.
1.15 FOOT MASSAGE 2
Click the FOOT MASSAGE button, foot massage motor switches massage intensity,
massage intensity switches among 0-1-2-3
1.16 FLAT 15
Click the FLAT button, the bed goes flat.
FCC
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC RSS warning
This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>