Carlon RC3196 Battery Door Chime Instruction Manual

Carlon RC3196 Battery Door Chime Instruction

INSTRUCTION GUIDE

Battery Door Chime RC3196
Congratulations on a wise purchase

ENCLOSED YOU WILL FIND

• Door Chime Receiver
• Door Chime Button
• Two 3-Volt lithium batteries (installed)
• Double-sided tape
• Screws
• Wall anchors

TOOLS NEEDED

• Large Phillips head screwdriver
• Ball-point pen

BATTERIES NEEDED (not included)

• Four C-cell alkaline batteries

DOOR CHIME RECEIVER

1. Open chime case by removing the bottom screw and remove the front cover.
2. While holding the front cover, disconnect the connector for the battery wires. Set the cover down.
3. Install (or replace) the four new “C” batteries in the battery holders. Make sure to match the polarity of each battery (+ and -) with the markings on each battery holder position.
4. Reconnect the battery wire connector. Re-install the front cover. Install the front cover screw.

TEST
Press Door Chime Button. Receiver should play tone.

MOUNTING DOOR CHIME BUTTON
Note: Mounting Door Chime Button on aluminum siding or metal door frame may reduce range.

If you want to cover the wire hole from your existing button, save mounting of the new Chime Button until after removing the existing button

1. Remove cover from back of Button by inserting ball-point pen into round hole at bottom of transmitter and gently pushing in on tab. Lift Chime Button cover away from the back plate.
2. For tape mounting: A) Make sure surfaces are free of dust, oil, and other substances that could affect adhesion. B) Attach double-sided tape to Chime Button back cover. C) Making sure that the end with the hook-shaped latch is facing down, press cover firmly to mounting surface.
3. For screw mounting: A) Place Chime Button back cover where desired and mark screw locations. B) Place Chime Button back cover against mounting surface and screw into marked locations using screws enclosed (may require drilling pilot holes on hardwoods).

MOUNTING DOOR CHIME RECEIVER
Receiver can mount on corner of wall. Before mounting Receiver, test desired location for operation.

For wall mounting

1. Mark screw location(s) onto wall for position.
2. Drill hole(s) into wall for plastic anchor(s). Place anchor(s) into hole(s) and install screw(s).
3. Leave screw head(s) extending about 1/8″ to 1/4″ from wall.
4. Hang receiver onto screw(s).

TO REPLACE BUTTON BATTERIES

1. Remove Chime Button from back cover by inserting ball-point pen into round hole at the bottom of the Button and gently pushing in on tab. Lift Chime Button cover away from the back plate.
2. Remove old batteries by placing a small screwdriver or ball-point pen in the slot directly beneath the batteries. Lift the top battery out of the battery compartment. Repeat with second battery. (Do not hit Chime Button to remove batteries – this could damage the Button.) Dispose of used batteries promptly. Keep away from children. Do not disassemble and do not dispose of in fire.
3. Replace old batteries with new batteries, positive (+) side up.

CAUTION – The batteries used in this device may present a risk of fire or chemical burn if mistreated. Do not recharge, disassemble, heat above 100ºC (212ºF), or incinerate. Replace with UL approved Type CR2032 3 volt lithium batteries from Carlon (RC3395D), Radio Shack, Toshiba, Sharp, NewSun, or Sony only. Use of another battery may present a risk of fire or explosion.

TROUBLESHOOTING TIPS

PROBLEM: Receiver does not sound when button is pressed.
SUGGESTION: Verify that Button batteries are installed correctly. Try replacing batteries first. Make sure Door Chime Receiver has fresh batteries. Check that Receiver and Button are placed within operating range.

PROBLEM: Receiver sometimes plays without anyone pressing Door Chime Button.
SUGGESTION: If another Wireless Door Chime System nearby is on the same frequency, it could accidentally trigger your system.

PRIVACY CODES and HOW TO CHANGE THEM

It is NOT necessary to change the privacy code unless interference occurs. If you need to change code

1. Use a nail clipper or wire cutter to cut and separate one of the wires (“A” through “E”) on Chime Receiver. Make sure cut wire does not touch any other wire.
2. Remove back cover off Chime Button and locate the wires, which are in the rectangular compartment adjacent to the batteries. The wires are designated “A” through “E” with letters located immediately above them.
3. Using a nail clipper or wire cutter, cut and separate the same wire that was cut on the Chime Receiver. Make sure that the cut wire does not touch any other wire.

Note: It doesn’t matter which wires are cut, but be sure that the same wire cut on the Button matches that of the Receiver. If the wire cut on the Chime Button does not match the wire cut on the Chime Receiver, the system will not work

Suggestion: Begin by cutting just one wire in the Chime Receiver and the same wire in the Chime Button. Test to see if the problem is eliminated. If the system is still not working properly, try cutting another wire. DON’T FORGET THAT EVERY TIME A WIRE IS CUT IN THE CHIME RECEIVER, THE CORRESPONDING WIRE MUST BE CUT IN THE CHIME BUTTON.

LIMITED WARRANTY

The product you have purchased is guaranteed against defects in workmanship and materials for the period stated on the package. Warranties implied by law are subject to the same time period limitation. Some states do not allow limitations on how long an implied warranty lasts, so this time limitation may not apply to you. If the product fails due to a manufacturing defect during normal use, return the product and dated sales receipt to the store where purchased for replacement OR send the product and the dated sales receipt to:

Lamson & Sessions 25701 Science Park Drive Cleveland, OH 44122 USA Attn: LHP Customer Service

Not Covered – Batteries, light bulbs, and other expendable items are not covered by this warranty. Repair service, adjustment and calibration due to misuse, abuse or negligence are not covered by this warranty. Unauthorized service or modification of the product or of any furnished components will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, set-up time, loss of use, postage, unauthorized service, or other products used in conjunction with, but are not supplied by, Lamson & Sessions. All requests for replacement must include a dated sales receipt (copies accepted). LAMSON & SESSIONS IS NOT LIABLE FOR LOST PROFITS, INDIRECT, SPECIAL, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION ANY SUCH DAMAGES DUE TO IMPROPER WIRING OR MISUSE OF THE PRODUCT. As some states do not allow the exclusion or limitation of incidental or consequential damages, the above limitation and exclusion may not apply to you. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada

ALSO AVAILABLE FROM CARLON

• Extend-A-Chime® – lets you hear your existing wired doorbell in remote areas of your home or yard
• Plug-in and Battery Doorbells and Chimes
• On/Off Remote Switches
• Touch and Automatic Lighting Controls

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. If you have questions or need further assistance, please call Lamson & Sessions at: 1-800-346-2646 Mon. – Fri., 9 a.m.- 4 p.m. EST Patents #5,365,214, #5,568,122, #5,680,102, & #5,680,112 25701 Science Park Drive
Cleveland, Ohio 44122 www.lamson-sessions.com

References

• ABB Installation Products, formerly Thomas & Betts Electrical Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>