Carlon HW2190 Heavy Duty Remote Control Instruction Manual
- June 4, 2024
- Carlon
Table of Contents
Carlon HW2190 Heavy Duty Remote Control
INSTRUCTION GUIDE
Heavy Duty Remote Control HW2190 Congratulations on a wise purchase!
ENCLOSED YOU WILL FIND:
- Transmitter
- Receiver
- 12-volt alkaline battery (installed)
TOOLS NEEDED
- Small Phillips head screwdriver
-
6 Screw
INSTALLATION
Four channels are available so that you can operate up to four systems at different locations around your home. (See channel options.)
Mounting the Receiver
To mount, hang the receiver securely on a #6 screw. A hole has been placed in
the back of the unit for this purpose. Do not hang by the cord. The HW2190
needs to be located below the wall outlet. This is to prevent rain from
running down the cord into the wall outlet.
Plug-in Receiver
Caution: This product requires a grounded outlet. If you do not have a grounded outlet, you may want to contact an electrician to upgrade your electrical system. If you are using this unit outdoors, note precautions.
Outdoor precautions: The HW2190 must be mounted with the receptacle facing down at all times (as illustrated) to prevent rain or moisture from entering the unit.
OUTDOOR RECEIVER PLACEMENT
Plug in the devices you wish to control.
Do not exceed the maximum load specifications listed.
IMPORTANT! The protective plug must be in place at all times to prevent water from entering the unit!
NOTE: The National Electric Code (and most local codes) require that outside outlets be protected by a Ground Fault Interrupter (GFI). Carlon recommends using a Carlon In-Use Weatherproof Cover for any outdoor outlets.
To Replace Transmitter Battery
Remove the top screw from the back of the remote control. Lift off the back
cover, remove old battery and dispose of it promptly. Insert a 12-volt
alkaline battery according to the (+,-) placement guides. Replace the back
cover along with the screw. The remote control will now be ready to operate.
Changing Jumper Code Channels (Optional)
The Heavy Duty Remote Control utilizes digital channels to send a signal
from transmitter to receiver. The user can change the channel if outside
interference occurs. If you use other wireless products in your home, there is
a slight possibility of interference. Use the following instructions to change
the current channel setting to a new setting.
IMPORTANT! If you change the channel combination on the transmitter, you must change the combination to the exact same combination on the receiver. If the channel combinations do not match, the units will not function!
TROUBLESHOOTING
CHANGING RECEIVER CODE
Changing Receiver Code:
- Unplug the unit.
- Remove the protective plug on the back of the receiver. This is located beside the hole to hang the unit.
- Channel codes are A,B,C,D.
- Move jumpers to select a code. Make sure to use the same code in the transmitter.
- Replace the protective plug.
- Plug in the unit and test with the transmitter.
- Remove the back cover.
- Channel codes are A,B,C,D.
- Select the proper channel by moving the jumpers.
- Replace back cover.
Light does not come on.
- The circuit breaker or fuse is turned off.
- The lamp switch is turned off.
- The bulb is defective.
- Signals from the transmitter are being blocked, or a receiver is out of range. Check for metal objects that could block the signal or reposition the receiver.
- A weak battery in the transmitter.
The light does not turn off.
- Pushing transmitter buttons too fast.
- Same as 4 & 5 above.
Light comes on randomly
- Short term power line failure.
- Ensure that another remote control is not on the same channel.
SPECIFICATIONS
- Detection Range: Up to 150 feet
- Maximum Load: 13 Amp resistive 1560 Watts resistive load 960 Watts incandescent 960 Watts fluorescent
- Rated Voltage: 120 VAC, 60 Hz
- Battery: 12-Volt alkaline
LIMITED WARRANTY
The product you have purchased is guaranteed against defects in workmanship and materials for the period stated on the package. Warranties implied by law are subject to the same time period limitation. Some states do not allow limitations on how long an implied warranty lasts, so this time limitation may not apply to you. If the product fails due to a manufacturing defect during normal use, return the product and dated sales receipt to the store where purchased for a replacement OR send the product and the dated sales receipt to: Lamson & Sessions 25701 Science Park Drive Cleveland, OH 44122 USA Attn: LHP Customer Service
Not Covered – Batteries, light bulbs, and other expendable items are not covered by this warranty. Repair service, adjustment, and calibration due to misuse, abuse or negligence are not covered by this warranty. Unauthorized service or modification of the product or of any furnished components will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, set-up time, loss of use, postage, unauthorized service, or other products used in conjunction with, but are not supplied by, Lamson & Sessions. All requests for replacement must include a dated sales receipt (copies accepted).
LAMSON & SESSIONS IS NOT LIABLE FOR LOST PROFITS, INDIRECT, SPECIAL, EXEMPLARY, INCIDENTAL, OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION ANY SUCH DAMAGES DUE TO IMPROPER WIRING OR MISUSE OF THE PRODUCT. As some states do not allow the exclusion or limitation of incidental or consequential damages, the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. If you have questions or need further assistance, please call Lamson & Sessions at 1-800-346-2646 Mon. – Fri., 9 a.m. – 4 p.m. EST.
25701 Science Park Drive Cleveland, Ohio 44122 www.lamson- sessions.com Made in China ©2005
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>