FLEXIHIRE FMS10 Electric Power Tools User Manual

Table of Contents

FMS10 Electric Power Tools
User Manual

Safe Operating Procedure
PPE Required

Complete pre-start checklist ·Read Manufacturers Operation Manual (www.flexihire.com.au)
Report any faults or damage to Flexihire 1300FLEXIHIRE
Do not wear loose clothing or jewellery
Do not operate equipment near pedestrians or people
Do not operate without the appropriate PPE as detailed
Do not operate equipment under the influence of drugs or alcohol

Refuelling Do not smoke, or introduce ignition source, always turn engine off and allow engine to cool first, relieve fuel pressure by loosening cap slowly, wipe clean any fuel spills prior to re-start, If fuel spilled on clothes change clothes, ensure cap is replaced & store fuel vessel away from work area
Do not breathe fuel vapour & replace cap securely after fuelling
Do not operate engine without adequate ventilation
Beware of hot surfaces on engine & other parts

Digging Safety

Always contact local authorities prior to performing any digging to identify underground services
Do not dig deeper than 1M without shoring
Beware of oxygen deficiencies and gas build up in pits and holes

Always use gas in well ventilated areas
Beware of inert gases that can cause oxygen deficiencies. These include Argon, CO2, Helium and mixtures of these.
Beware of Flammable gases such as acetylene, LPG & Hydrogen, always keep away from ignition sources and store in well ventilated areas
Always use flashback arrestors at the regulator and torch end when cutting, heating or welding with Acetylene.
Gases can not always be seen, heard or smelt so beware when they are present on your site
Beware of welding arc rays they can cause severe burns ·Always wear non flammable clothing
Beware of welding fumes as they can be toxic always check MSDS sheets of the welding consumable being used and of the steel being welded

Operators should familiarise themselves with the equipment. If you are unfamiliar with the equipment seek advice
Always wear the appropriate safety equipment for the job, ensure that PPE meets Australian Standards, does not cause further hazards. e.g. where there is risk of entrapment, gloves may not be an appropriate form of PPE.
Only qualified personnel to perform maintenance and repairs
Ensure your workspace is kept clean and free from hazards
Do not block airflow to machine as it can cause overheating
Do not weld or cut pipes, tanks or vessels that contain pressure or flammable substances
Do not climb in trees or on roofs with power tools or other equipment
Never reach from one location with one hand to perform a function or operate a tool with the other hand. Use two hands on all tools.
Keep hands and body parts away from moving parts as they can cause serious injury and entanglement
Always switch off equipment prior to performing any work or adjustments

Risk Assessment

General Electricity Safety

Ensure all electrical equipment has a current test tag within 3 months
Do not operate equipment in or around water or damp environments
It is recommended to use a safety switch to power this equipment
Ensure the power lead is well stowed and do not present trip hazards
Isolate the power by removing the plug prior to performing any work on the equipment including prior to changing leads or tools or bits
Always uncoil power leads prior to use

Compressed Air & Water

Never puncture, weld, drill or cut pressure vessels containing air
Always ensure pressure vessels are free of pressure before working
Do not use compressed air for breathing or for air flow on humans
Never direct air flow at another person
Always wear eye protection when working with compressed air
Pressure cleaners produce very pressure jet streams that should never be used for cleaning body parts or other people
Beware of high pressure deflecting off jobs back toward the operator

Falls from as little as 1M can cause serious injury, always protect yourself and others from falls
Always maintain 3 points of contact when working at height
Do not carry heavy loads at height
Always ensure no people can access the area under the working height
Ladders inspect ladders prior to use, never stand on the top rung, always use in the fully open position and never use damaged ladders, ensure aluminium or steel ladders are no where near electrical cables, use slip resistant treads
Do not carry heavy loads on ladders
Scaffolds Inspect prior to use, always have appropriate handrails, kickboards and access platforms, do not install near electrical cables or within reach of them, ensure base is secure and castors locked in place. Do not assemble a scaffold with a platform height of 4M or greater this can only be done by a licensed scaffolder.
Trestles and planks Inspect prior to use, keep away from electrical cables, do not use damaged trestles or planks, always ensure trestles are fully opened, use access ladders and restrain at the top.
Never allow children at height
EWP It is recommended to use Elevated Work Platforms where possible, enquire at Flexihire for further details

Lifting, Chains & Jacks

Beware of tension stored in chains that can release violently and cause flick back when under loads
Keep fingers clear of all pinch points
Always use the appropriate chains with the correct weight load limit
Always ensure the suitability of the overhead structure if using it for lifting, winching or pulling
Use correct size jacks for the load weight and ensure jacks are placed under a solid part of the structure and cannot slip
Always have a backup system when working under a jacked up item such as frame stands or hard wood timber blocks
Do not use levers, pinch bars or pry bars for the purposes of lifting equipment

FMS10-5.1.3.9.0 SOP General Safety
Version #: FLX 3.2
Issue: October 2021
Review: October 2026