SEKONDA IS47F Men’s Watch User Guide
- October 27, 2023
- SEKONDA
Table of Contents
SEKONDA IS47F Men’s Watch
BUTTONS
Button operations are indicated using the letters shown below Illustration.
- A Reset
- B Mode
- C – EL backlight
- D- Start/ Stop
DISPLAY
The screen is shown below:
ATTENTION
- Never try to open the case or remove its back cover.
- Do not operate the buttons underwater.
- Should moisture appear inside the watch, have it checked immediately by your dealer. Otherwise, it can cause erosion of the metal parts of the watch.
- Although the watch is designed to withstand normal use, you should avoid rough use or dropping the watch.
- Avoid exposing the watch to extreme temperatures.
- Wipe the watch with a dry and soft cloth only.Avoid allowlng It to come Into direct contact with chemlcal materials that can cause deterioration of the plastic parts of the watch.
- Avoid wearing the watch In electromagnetic or static conditions.
MODE SELECTION
- Press “B” to change the mode in the following sequence: Timekeeping Mode Alarm Mode- Stopwatch Mode – Dual Time Mode.
TIMEKEEPING
- 12/24H Format
- Hour, Minutes, Seconds,
- Day of the week, Date;
- 100 years Calendar (2000 2099).
ALARM
- Hourly time signal;
- The alarm sounds at the
- preset time each day.
STOPWATCH
- 1/100 second unit;
- Measuring range: 0’00″0023:59’59”
DUAL TIME
- Time setting for other time zones.
TIMEKEEPING
- 12/24H Format
- In the timekeeping mode, press “A” to switch between 12/24H formats.
- Calendar
- In the timekeeping mode, press and hold “D” to display the Year, Month, and Date.
Time Setting
- In the timekeeping mode, press and hold “A” until the seconds begin to flash (the flashing indicates that you are in setting mode);
- Press •D• to reset the seconds;
- Press•e• to change to the next selection;
- Press “D” to increase the number, and press and hold “D” to increase at high speed;
- Repeat steps 3 and 4tochangethe selection in the following sequence: Seconds – Hour- Minutes- YearMonth – Date;
- Press “A” to exit the set state, after you have set the time. (The day of the week is auto-displayed in accordance with the year, month, and date setting).
ALARM
- Alarm and Chime In the alarm mode, press “D” to on/off the alarm and chime in the following sequence: Alarm& Chime off – Alarm on- Chime on- Alarm & Chime on.
- The chime is the hourly time signal.
Alarm Time Setting
- In the alarm mode, press and hold “A” until the nurse flash. (The hour flashing Indicates that you are in setting mode);
- Press “D” to increase the hour, and press and hold “D” to increase at high speed;
- Press “B” to select the minutes;
- Press “D” to increase the minutes, and press and hold”D” to increase at high speed;
- Press “A” to exit the set state, after you have set the time.
- The alarm sounds at the preset time each day for about 60 seconds, press any button to break it.
STOPWATCH
A Lap Time
- In the stopwatch mode, press “D” to start the stopwatch;
- To stop the stopwatch press “D”again;
- Press “A” to reset the stopwatch.
Split Time
- In the stopwatch mode, press “D” to start the stopwatch:
- Press “A” to display the split time the stopwatch will continue timing internally:
- Press “A” to clear the split time and continue time measurement;
- Repeat steps 2 and 3 to measure multiple split times;
- Press “D” to stop the stopwatch.
- Press “A” to reset the stopwatch.
DUAL TIME
Dual Time Setting
- In the dual-time mode, press and hold”Auntil enourDeginstotlash (the flashing indicates that you are in setting mode),
- Press “D” to increase the no, press, and nO1dD to increase at high speed;
- Press “B” to select the minutes
- Press to change the minutes (press once to add 30 minutes);
- Press “A” to exit the set state after you have set the time.
BACKLIGHT
- The backlight uses an electro-luminescent that causes the display to glow for easy reading in the dark.
Using The EL Backlight
- In any mode, press “C” to illuminate the display for about 3 seconds.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>