PROBUILDER 99008 Universal Mitre Saw Horse Instruction Manual
- June 2, 2024
- PROBUILDER
Table of Contents
Model 99008
MITRE SAW STAND
Instruction manual
Introduction
To get the most out of your new mitre saw stand, please read this instruction manual before use. Please also save the instructions in case you need to refer to them at a later date.
Main components
- Frame, 1 pcs.
- Length adjustment screw, 4 pcs.
- Height adjustment screw, 2 pcs.
- Adjustable workpiece support, 2 pcs.
- Saw mounting rail, 2 pcs.
- Bolt, nut and washer M6x60, 4 pcs.
- Bracket, 2 pcs.
- Bolt, nut and washer M6x20, 2 pcs.
- Bolt, nut and washer M8x60, 2 pcs.
- Stand extension, 2 pcs.
Technical data
Working length: | 118.5-202.7 cm |
---|---|
Working height for workpiece supports: | 88.0-101.2 cm |
Stand height: | 81.7 cm |
Diagonal tube measurement, legs: | Ø38 mm |
With adjustable workpiece supports
Max. load:| 150 kg
Special safety instructions
Before use, check that the mounted saw is securely attached to the mitre saw stand.
Follow the safety instructions that apply to the saw you use along with the mitre saw stand.
Assembly
- Place the frame (1) on a mat or similar so that it does not get scratched. Tilt the frame legs fully out so that the spring lock is released.
- Insert the workpiece supports (7) into the holders at each end of the stand extensions and screw them tight using a finger screw (2).Screw two finger screws to each end of the mitre saw stand (to secure the stand extensions).Fit the supplied brackets to the rails.
- Place the rails (5) on the mitre saw stand and clamp them securely in place using the handle. They should be positioned at a distance equal to the width of the mitre saw.
- Push a bolt (6) into the rail, as shown in the drawing.Attach the saw onto the mitre saw stand so that the four bolts go through the mounting holds in the saw’s base plate.
Place a washer, a spring washer and a nut on each bolt and tighten the nuts to fully secure the saw to the rails.![PROBUILDER 99008 Universal Mitre Saw Horse
-
secure the saw](https://manuals.plus/wp- content/uploads/2022/12/PROBUILDER-99008-Universal-Mitre-Saw-Horse-secure-the- saw.png)
- The mitre saw stand is now assembled and ready for use.
Cleaning and maintenance
Check regularly that all nuts and bolts are tightened properly.
Use a brush to remove any filings and dirt from the mitre saw stand.
Stubborn dirt can be removed using a wellwrung cloth.
The mitre saw stand must not be washed or high-pressure washed.
Regularly lubricate all bolts and nuts using acid-free oil or lubricating
spray.
Fold the mitre saw stand up and store it in a dry, dust-free location indoors
when it is not in use.
Service centre
Note: Please quote the product model number in connection with all
inquiries.
The model number is shown on the front of this manual and on the product
rating plate.
For:
- Complaints
- Replacement parts
- Returns
- Guarantee issues
- www.schou.com
Manufactured in P.R.C.
Manufacturer:
Schou Company A/S
Nordager 31
DK-6000 Kolding
All rights reserved. The content of this manual may not be reproduced, either
in full or in part, in any way by electronic or mechanical means, e.g.
photocopying or publication, translated or saved in an information storage and
retrieval system without written permission from Schou Company A/S.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>