CANVAC CFK3301V Tower Fan Instruction Manual

CANVAC CFK3301V Tower Fan

Thank you
for your trust and for purchasing our product. This quick start guide is supplied to help you get started using this product.
Make sure you have received an undamaged product. If you do find transport damage, please contact the seller from which you purchased the product, or the regional warehouse from which it was supplied.

IMPORTANT SAFETY INFORMATION!

WARNING
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following:

1. This product is only suitable for indoor use and should not be used outdoors.
2. Non-professional personnel or unauthorized repair personnel may not repair or modify the appliance by themselves.
3. Before plugging into the power supply, please check that the rated voltage match-es the voltage in your home.
4. Keep at least 1.5 meters away from fire source or flammable materials, and avoid direct sunlight.
5. Do not use the appliance near objects that are flammable, explosive, subject to heat deformation, discoloration or deterioration. Do not use the appliance in places with high levels of dust.
6. Always use turn off the appliance before unplugging it.
7. To avoid overheating, never cover the heater.
8. Never insert any wire or other foreign object into any hole in the appliance, to avoid electric shock.
9. Do not position the heater so that it blows towards the power socket or underneath the power socket. The power socket should be located behind the fan when the heater is in use.
10. Do not share the socket with other high-power appliances.
11. Do not use this heater close to a bathtub, spray head or swimming pool.
12. This appliance must be connected to a CE-approved fixed socket that can supply the rated working current. Do not use a mobile multi-purpose socket.
13. If the heater is covered or incorrectly positioned it may pose a fire risk. Do not use a programmer or timer that can automatically connect the power supply.
14. If the heater fails, please turn off the power and unplug the power cord immediately.
15. Before use, check the power cord and the plug. If the power cord is damaged it must not be disassembled or replaced by the user. It must be replaced by the manufacturer’s maintenance department or a similar professional.
16. Children, elderly people, or patients who are unable to take care of themselves should only use this appliance under the supervision of an adult, to prevent accidents.

PRODUCT DESCRIPTION

This product uses PTC heating to heat the air, which can quickly increase room temperature. There is no open flame, making it safe, efficient and energy- saving.

BASIC PARAMETERS

REMOTE INTRODUCTION

The device can be switched on and off by pressing the ON/OFF button.
Press the Sleep mode button on the remote control. The display will show “LL” and the airflow will be reduced. Press again to exit Sleep mode. Only works in Cool mode; in Warm mode this button has no function. (You can also exit this mode by pressing the Airflow increase + button.)
Press the Turbo mode button on the remote control. The display shows “HH” and the airflow increases to maximum. Press again to exit Turbo mode. Only works in Cool mode; in Warm mode this button has no function. (You can also exit this mode by pressing the Airflow increase + button.)
Press the Oscillation button to turn on the oscillation function. The fan can swing left and right 80 degrees. Press this button again to stop oscillation.
Press once to turn on UV sterilization; the display will show “U”. Press again to turn off UV sterilization. UV sterilization will automatically shut down after 1 hour.
Press the Cool mode button to enter Cool mode. You can adjust the airflow in this mode. Note: Cool mode is the default mode when the appliance is turned on.
Press the + button on the left side of the remote control to increase the air- flow; press the – button on the left side of the remote control to decrease the airflow. There are 9 airflow settings in Cool mode and 4 airflow settings in Warm mode.
Press the Warm mode button to enter Warm mode. The digital display will show the ambient temperature. You can adjust the airflow and temperature in this mode. Turbo mode / Sleep mode are not available in Warm mode.
In Warm mode, press the temperature button on the right side of the remote control to set the temperature (1–30°C).
Note: this button does not work in Cool mode.
Press the timer button on the remote control to set the timer between 1 to 8 hours. A small “.” will flash in the lower right corner of the digital display to indicate that the timer has been set.

Warning
Issues that may occur due to the overlap of frequencies of remote controls are listed below.

1. This bladeless heater may react when you use a remote device for other appliances.
2. When using the remote control of this bladeless heater, other electrical appliances may react.

The switch on the remote will turn this fan to standby, but will not turn it off completely. Use the ON/OFF switch on the body of the fan to turn it off when not in use.
If the fan will not be used for a long time, please unplug the power cord.

FILTER REPLACEMENT

This appliance is equipped with a purifying air filter, which can purify the air. Note that the product must ALWAYS have a filter in place when it is running.

Replacement method:

1. Turn off the appliance and unplug it from the power socket.
2. Turn the top cover anticlockwise to unlock it and lift the top cover and filter off the body of the fan.
3. Separate the top cover from the old filter.
4. Fit the top cover over the new filter.
5. Refit the new filter and cover on the body of the fan and turn the top cover clockwise to lock it.

Warm Mode Instructions

• Press the Warm mode button and the display will show the ambient temperature.
• Press the temperature button to set the temperature; the display will flash and you can now set the temperature to between 1 and 30°C.
• The set temperature should be higher than the ambient temperature, otherwise the heater will not turn on.
• When the ambient temperature reaches the set temperature, the heating function will stop and the airflow will be reduced to the minimum setting.
• When the ambient temperature drops below the set temperature, the heating function will automatically be reactivated.

Set temperature > ambient temperature: heating function on.
Set temperature ≤ ambient temperature: heating function stops.

Note: The default setting temperature is 25°C. In Warm mode, when the ambient temperature is below 0°C, the display only shows 01; it does not display a negative temperature value. The appliance will only run for 12 hours in Warm mode, and will then turn off automatically. Restart by pressing the power button or by using the remote control.

CONTROL PANEL

Insert the plug into a power socket, turn on the power switch in the base and the fan will enter standby mode:
Press the power button on the body. The buzzer will beep once and the fan will start running.
Press and hold the power button for 2 seconds, the buzzer will beep twice, and then stop running after you release the button.

Adjusting the airflow
When the fan is running in Cool mode, press the power button on the body to adjust the airflow between 1 and 9.
When the fan is running in Warm mode, press the power button on the body to adjust the airflow between 1 and 4.

Oscillating operation
Press and hold the power button for 1 second, the buzzer will beep once and the fan will start oscillating.
Press and hold the power button for 1 second again, the buzzer will beep once and the fan will stop oscillating.

INSTALLATION LOCATION AND PRECAUTIONS

Location

Please place this product on a level surface. Avoid putting it on an unstable surface (such as a sloping or soft surface) to prevent it from falling over. Please do not use in high temperatures and humidity (bathroom, kitchen ).

Safety: this fan includes an overheat protection sensor and an automatic fail-safe that cuts power to the unit if it’s accidentally tipped over or overheats. If this sensor is triggered, unplug the fan and allow it to cool down. Check and remove any obstructions before restarting the fan and be sure to place it on a hard, level surface.

BATTERY INSTALLATION AND TROUBLESHOOTING

Battery installation

1. Open the remote control battery cover.
2. Load two new AAA (No. 7) dry batteries.
3. Close the battery cover of the remote control.

Troubleshooting

socket?
Remote does not work| Is the battery dead?

Is the battery installed correctly?

Is the remote control pointed at the signal receiver?

Noise from fan or low airflow| Check air purifying filter; if full of dust,

clean or replace.

If the above steps do not fix the fault, please contact customer service; do not attempt to dismantle or repair the appliance yourself.

MAINTENANCE

Unplug from the power socket before performing maintenance.

Please do not immerse or spray the fan with water as this may damage the appliance. Do not use banana oil, benzeFne, alcohol, bleach or metal objects to wipe the surface of the fan, as this may cause discoloration of the surface.

Surface cleaning

• Wipe the surface with a soft, dry cloth.
• If especially dirty, wipe with a soft cloth and mild detergent.
• Then wipe with a dry soft cloth.

Air inlet/outlet
Use a soft brush or a vacuum cleaner to clean the dust from the air inlet and outlet. Clean regularly to avoid the build-up of dust. Too much dust is unhealthy and will reduce fan efficiency.

Remote control
Gently wipe the surface of the remote with a soft, dry cloth. If you don’t use the fan for a long time, remove the battery from inside the remote control to prevent it discharging.

Storage

• If the fan will not be used for a long time it can be placed in a plastic bag after cleaning.
• Please avoid storing it anywhere that is subject to vibration or near other electrical appliances with cooling/heating functions.
• Please avoid placing it in direct sunlight, or areas subject to high temperature and humidity.
• Please keep out of the reach of young children.

WIFI-OPERATION

OPERATING THROUGH TUYA SMART
Download and install Tuya smart App.
Use your smartphone to scan the QR code below to download the Tuya smart App.

Or search Tuya smart in either Apple Store or Google Play to download and install the App.

Step 1
Run the Tuya smart App and register a new account or log in with your existingac-count and password. You will need to add your Smart Fan to the same WiFiRouter as your phone by following the below instructions.

Step 2
Open the App and tap Add Device or “+” icon to add a device. Select Small Home Appliance in the list of devices, and tap the Fan icon. (fan (Wi-fi))

Step 3
Make sure that the power is connected to the bladeless fan before use. Plug the bladeless fan into the power outlet. Then, press and hold the power button for 5 seconds. Ensure your phone is connected to your local 2.4GHz Wi-Fi router. Type in your Wi-Fi password and tap Confirm to search the device.

Step 4
The LED display will indicate the Wi-Fi symbol, and it will flash quicky. Tap “con-firm indicator rapidly blink”. Once the configuration is complete, the indicator light will stop blinking rapidly.
NOTE: If the bladeless fan failed to establish a connection, make sure there is no special symbol in your Wi-Fi name (should only contain letters and numbers) and password, and try again by repeating Step 3 & Step 4 to set it up.

Step 5
Once connected, you can rename the bladeless fan and select the Room (e.g., Living Room) where the bladeless fan is located. It helps you identify the device when you want to cast to it.

Step 6
You can tap the Power icon to turn on/off the bladeless fan. Swipe the Blue Circle to adjust the fan speed. Tap Oscillate to adjust the oscillation. Tap Boost to set your wind speed to maximum. Tap Time to set the time between 1 to 8 hours.

The information may be subject to changes. Inadvertent errors in information may occur.

Canvac’s guarantee of quality for the consumer (does not include wear parts). Read more at www.canvac.se/garantier.

Elon Group
Canvac products are distributed and marketed by Elon Group AB. Elon Group AB Bäcklundavägen 1 | 702 03 Örebro Sweden Elon Group | +46(0)10-220 40 00 | elongroup.se
Support and service: canvac.se

References

• Canvac - Skönare och bättre luft inomhus
• Start - Elon Group
• Domain reserved.fi is for SALE - Catcha.fi
• Parked
• Websupport | En av Europas största leverantörer av Webbhotell och Domännamn!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>