66883 JascoPro Series LED Direct Wire Dimmable Light Fixture Instruction Manual

66883 JascoPro Series LED Direct Wire Dimmable Light Fixture

Specifications

• Length of fixture: 36” Nominal lumens: 1366
• Voltage: 120 Hertz: 60
• Nominal CRI: 91 Nominal wattage: 15.7
• Efficacy (lm/w): 86 CCT: 3000K
• Beam angle: 110.6 Lifetime: 50,000 hours
• Warranty: 5-year limited warranty

Design Features

• Premium LED 36in. direct wire light bar
• High-quality steel housing and in-wall dimmer compatible
• High-powered fully diffused LED light source with no hot spots
• 1366 lumens, 3000K warm white light

Installation Recommendations

• Includes all mounting hardware and instruction manual for easy installation
• Indoor use only
• Product is UL listed and Energy Star rated

DIMENSION

BOX CONTENT

Certifications & Compliances

• Compliances, specifications and availability are subject to change without notice.
• Distributed by Jasco Products Company LLC 10 E. Memorial Rd., Oklahoma City, OK
• Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between 7AM-8PM, M-F, Central Time.
• ©Jasco 2022

INSTALLATION INSTRUCTION

Before installing, read all safety instructions listed at the end of this manual. Consult a local licensed electrician or electrical contractor if you are not sure about installing the direct-wire fixture yourself. Save these instructions for later use.

• Step 1: Turn power OFF. Ensure that electricity is TURNED OFF at the main circuit breaker or fuse box. DO NOT ATTEMPT TO INSTALL THE FIXTURE WITH POWER ON
• Step 2: Select mounting location. Choose a location that is clean, dry and capable of supporting the fixture. NOTE: The ideal mounting orientation for the light fixture is near the front lip of your cabinets as shown in the illustration (see Figure 1) — this provides the best light distribution across a countertop.
• Step 3: Remove lens/diffuser. Remove the lens/diffuser by lightly pulling the rear edge towards you and upwards.
• Step 4: Remove housing from base. Using a #1 Phillips-head screwdriver (not included), remove the screws securing the housing to the base. Firmly push forward on the bottom front of the housing to unlatch it from the catch points — retrieve the hardware kit inside.
• Step 5: Remove knock-out tab. Choose a knock-out location from those provided on the fixture and carefully remove it using a screwdriver. NOTE: When choosing a knock-out, consider which part of the fixture will be closest to power.
• Step 6: Strain relief. Remove the nut and lock washer from the strain relief and insert the threaded end into the newly created knock-out hole on the fixture. Reattach the lock washer and nut and secure the strain relief in place — tighten with pliers if needed (not included).
• Step 7: Mark screw locations. Hold the base in place and mark the location for each screw with a pencil using the keyholes for guidance (see Figure 2).
• Step 8: Drill pilot holes. Create pilot holes on each pencil marking using a drill and a 1/16in. drill bit for softwoods and a 3/32in. drill bit for hardwoods.
• Step 9: Insert screws. Use a #1 Phillips-head screwdriver to drive each of the included screws into the pilot holes, leaving the heads protruding approximately 1/8in. from the surface (see Figure 3).
• Step 10: Mount fixture. Align the keyholes on the fixture with the two installed screws and slide it into place (see Figure 4) — tighten screws as needed.
• Step 11: Hang cover on base. For ease of installation, hook the cover onto the mounted base using the built-in flanges.
• Step 12: Insert power cable into fixture. Install the armored house cable to meet electrical codes. Carefully thread the cable through the strain relief and into the fixture, tightening the two screws on the strain relief to secure it into place.
• Step 13: Hot AC wires (black). Connect the hot (black) AC supply wire to the hot (black) wire of the fixture. Secure the connection with the quick connects (see Figure 5). Gently pull the wires to check for tightness.
• Step 14: Neutral AC wires (white). Connect the neutral (white) AC supply wire to the neutral (white) wire of the fixture. Secure the connection with the quick connects (see Figure 5). Gently pull the wires to check for tightness.
• Step 15: Grounding wires (green/copper). Connect the ground (green/copper) AC supply wire to the ground (green/copper) wire of the fixture. Secure the connection with the quick connects (see Figure 5). Gently pull the wires to check for tightness.
• Step 16: Arrange wires and reattach housing. Ensure that no bare wires are exposed after making the electrical connections. Arrange the connected wires inside the fixture without “pinching” any and reattach the housing.
• Step 17: Reattach lens/diffuser. Reattach the lens/diffuser to the housing by gently pushing it back into place.
• Step 18: Restore power. With everything properly installed, restore power at the main circuit breaker or fuse box.

DIMMING FUNCTION

To use the dimming function, please use a compatible LED dimmer. Follow the dimmer setup instructions for optimal performance.

FCC STATEMENT:

• Suppliers Declaration of Conformity | Model #: 66868, 66874, 66878, 66883, 66886 | Jasco Products Co., 10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com
• This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
• FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

WARNING

• RISK OF ELECTRIC SHOCK
  • DO NOT USE IN WET LOCATIONS.
  • USE INDOORS ONLY.
  • TURN POWER OFF BEFORE SERVICING — SEE INSTRUCTIONS.
  • PROPERLY GROUND FIXTURE.
  • ENSURE THAT NO BARE WIRES ARE EXPOSED OUTSIDE THE ELECTRICAL CONNECTIONS.
• RISK OF INJURY
  • SOME METAL PARTS IN THE FIXTURE MAY HAVE SHARP EDGES. TO PREVENT CUTS AND SCRAPES, WEAR GLOVES WHEN HANDLING THE PARTS.
  • DO NOT OPERATE THE UNIT WITH A MISSING OR DAMAGED LENS.
  • DO NOT INSTALL ON WALLS OR VERTICAL SURFACES.
  • ACCOUNT FOR SMALL PARTS AND DESTROY PACKING MATERIAL, AS THESE MAY BE HAZARDOUS TO CHILDREN.
• RISK OF FIRE
  • MINIMUM 90º C SUPPLY CONDUCTORS.
  • NOT INTENDED FOR ILLUMINATION OF AQUARIUMS.
  •  NOT INTENDED FOR USE ABOVE STOVES, COOK TOPS OR SINKS.
  • NOT INTENDED FOR RECESSED INSTALLATION IN CEILINGS OR SOFFITS.
  • NOT INTENDED FOR SURFACE INSTALLATION INSIDE OR ON TOP OF BUILT-IN FURNISHING

ABOUT COMPANY

• Distributed by Jasco Products Company LLC,
• 10 E. Memorial Rd., Oklahoma City, OK 73114.
• This Jasco product comes with a two-year limited warranty. Visit www.byjasco.com for warranty details.
• Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between 7AM-8PM, M-F, Central Time.

PRODUCT OVERVIEW

PRODUCT FEATURES

Streamlined Control

Fully manage the way your space is lit by connecting your fixture with any compatible in-wall dimmer.

Direct Wire

Easily installed with the included hardware, you can eliminate cord clutter and maintain a clean, modern style.

References

• Jasco

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>