JASCO ZW5313 Z-Wave 700s 2-Button Simple Controller User Manual
- June 5, 2024
- JASCO
Table of Contents
ZW5313 Z-Wave 700s 2-Button Simple Controller
**User Manual
**
ZW5313 Z-Wave 700s 2-Button Simple Controller
Portable Wireless
Hub/Panel Remotehttps://byjasco.com/HEP-ET/20000-99999/37792/manual
Read instructions or watch the easy-to-follow video.
Scan QR code or visit goo.gl/xBMTZa.
Never lose track of your remote with a magnetic remote stand.
Visit ezzwave.com.
Purchase additional items at ezzwave.com or visit your
local retailer.
**DO NOT RETURN THIS PRODUCT TO THE STORE**
If you have any problems or questions, contact our U.S.-based Consumer Care at
1-800-654-8483, option 1,
Monday–Friday, 7 AM–8 PM Central Time.
For the most up-to-date product support, accessories, electronic (PDF) format
manuals, and more, visit
www.byjasco.com/support.
- No user-serviceable parts in this unit.
WARNING
NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT
Z-WAVE-ENABLED DEVICES SHOULD NEVER BE USED TO SUPPLY POWER TO OR CONTROL THE
ON/ OFF STATUS OF MEDICAL OR LIFE SUPPORT EQUIPMENT.
Requires two CR2032 coin cells.
Observe polarity markings (+), (-).
CAUTION
- BATTERIES MAY LEAK HARMFUL LIQUIDS OR IGNITABLE MATERIALS OR EXPLODE CAUSING INJURY AND PRODUCT DAMAGE.
- DO NOT MIX OLD AND NEW OR OTHER BATTERY TYPES.
- REPLACE ALL BATTERIES AT THE SAME TIME.
- REPLACE EXHAUSTED BATTERIES IMMEDIATELY.
- REMOVE BATTERIES IF THE PRODUCT IS TO BE UNUSED FOR EXTENDED PERIODS.
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7 AM – 8 PM, M-F, Central Time, or www.byjasco.com if the unit should prove defective within the warranty period.
Jasco Products Company LLC, Building B
10 E. Memorial Rd.
Oklahoma City, OK 73114.
SPECIFICATIONS
ZW5313
Battery operated: 2x CR2032 lithium 3V batteries
Signal (frequency): 908.4/916MHz
Range: Up to 150ft. line of sight between the wireless controller and the
closest Z-Wave receiver module
Operating temperature range: 32-104° F (0-40° C)
For indoor use only
Specifications are subject to change without notice due to continuing product
improvement
Getting to know your new Z-Wave device
- No wiring is necessary.
- Two function buttons. Each button supports up to three actions (up to six unique actions).
- Fits multi-gang wallplates (not included) for installation beside existing switches.
Actions
Actions allow the user to select predetermined actions and assign them to
start or stop with the press of a button. The controller sends the button
press information to the hub, which executes the action. An action can be many
combinations of scenes, groups or events, and is greatly dependent on the
hub’s capabilities.
A. LED indicator
B. Buttons
Single press — sends action 1 for that button to the hub/controller.
Double press — sends action 2 for that button to the hub/controller.
Triple press — sends action 3 for that button to the hub/controller.
C. Battery tray notch — located on the side
Installing or replacing the battery
- Turn the remote to the right side to reveal a slot in the lower right corner of the controller.
- Insert a 1/4in. standard flat-blade screwdriver into the slot and twist to release housing clamps. Once the edge is raised, gently move around the frame to release both halves.
- Remove old batteries by sliding them out of the top and bottom of the holders. Place new batteries with (+) side facing up.
- Snap the controller halves together.
**Installing the remote beside the existing switch
**
-
Remove wallplate from existing switch.
-
Screw the remote bracket assembly onto the new wallplate (not included).
NOTE: Use provided 1/4in. low-profile mounting bracket screws. -
Place the wall plate assembly onto the existing switch and secure it with existing wallplate screws.
Installing remote with single wallplate
Bracket design will work with standard electrical boxes and low-voltage mud
rings.
- Using the supplied 1in. screws secure the mounting bracket to the box.
- Place the wallplate (not included) onto the mounting bracket and secure with provided 1/4in. low-profile mounting bracket screws.
Mounting remote on wall mount
- The wall-mount bracket is magnetic and will hold the remote in place. Gently place the remote on top of the remote bracket using the alignment bar to center the remote.
Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other
Z-Wave certified devices from other manufacturers and/or other applications.
All non-battery
operated nodes within the network will act as repeaters regardless of vendor
to increase the reliability of the network.
This device supports Association Command Class (3 Groups)
- Association Group 1 supports Lifeline, Battery Reports, Device Reset Locally Notification, Central Scene, Indicator Report
- Association Group 2 supports Basic Set and is controlled by pressing the Up or Down button once.
- Association Group 3 supports Basic Set and is controlled by double-pressing the UP or Down button
- Each Association Group supports 5 total nodes
Adding your remote to a Z-Wave network
-
Follow the instructions for your Z-Wave certified hub to add a device to the Z-Wave network.
-
Once the hub is ready to add your device, press and hold either button for three seconds.
-
The LED will flash two times when the remote sends add notification (NIF).
-
The LED will keep lighting up for one minute if inclusion is successful.
NOTE: Some hubs require an additional step for secure inclusion. When prompted, scan the QR code on the back of the remote or type the 5-digit pin code located on the back of the remote. -
Following the instructions for your Z-Wave certified hub, assign actions for each button press. An action can be many combinations of scenes, groups or events, and is greatly dependent on the hub’s capabilities.
If prompted by the controller to enter the S2 security code, refer to the QR
code/security number on the side of the box or the QR code label on the
product (see Figure 1). Enter the 5-digit PIN code.
Figure 1:
https://byjasco.com/HEP-ET/20000-99999/39339
**Removing your remote from a Z-Wave network
**
- Follow the instructions for your Z-Wave certified hub to remove a device from the Z-Wave network.
- Once the hub is ready to remove your device, press and hold either button for three seconds.
- The LED will flash two times when the remote sends a remove notification (NIF).
Returning your remote to factory defaults
- Press and release button 1 10 times quickly. All button presses must be within six seconds.
- The LED will flash five times when completed successfully.
NOTE: This should only be used in the event your network’s primary
controller/the hub is missing or otherwise inoperable.
NOTE: SmartStart-enabled products can be added to a Z-Wave network by
scanning the QR code on the product with a controller providing SmartStart
inclusion. No further action is required and the SmartStart product will be
added automatically within 10 minutes of being switched on in the network
vicinity.
Wakeup interval information
- Role type: Reporting Sleeping Slave (RSS)
- Wakeup interval: Supports a range of 0, 3600 seconds – 86,400 seconds (off, 1-24 hours)
- Default = 86,400 seconds (24 hours)
- Keep the default wakeup period to maintain the longest possible battery life. However, the minimum configurable value should be no less than 3600s (1hr) or to OFF 0s.
FCC/IC
This device complies with Part 15 of the FCC and Industry Canada license-
exempt RSS standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
FCC NOTE : The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee interference will not occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
Important note: To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted. Any change
to the antenna or the device could result in the device exceeding the RF
exposure requirements and void the user’s authority to operate the device.
Responsible Party – US Contact Information
ZW5313
FCC — U2ZZW5313
IC: 6924A-ZW5313
Jasco Products Company
Model: ZW5313/53829
10 E. Memorial Rd., Oklahoma City, OK 73114 |
1-800-654-8483
CAN ICES-3(B)/NMB-3(B)
All brand names shown are trademarks of their respective owners.
MADE IN CHINA
DISTRIBUTED BY
JASCO PRODUCTS COMPANY LLC,
10 E. MEMORIAL RD.,
OKLAHOMA CITY, OK 73114.
©JASCO 2020 | 53829
ZW5313 | 07/24/20 v1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>