JASCO 81018 Smart Water Leak Sensor Instruction Manual

JASCO 81018 Smart Water Leak Sensor

Product Information

Specifications

• Model: 81018 ZWN6310
• Indoor use only
• SmartStart enabled for easy setup
• Z-Wave compatible

Product Usage Instructions

Installation:
The smart water leak sensor is designed for indoor use. Follow these steps to install the sensor:

1. Place the sensor near potential water sources such as sinks, toilets, dishwashers, etc.
2. Position the sensor on the floor or cabinet base to ensure the three contact pins are in contact with the surface.
3. If needed, use the double-sided tape or screws provided to mount the sensor to a wall.
4. Connect the sensor to the base aligning the arrows and insert the detachable probe into the sensor port.
5. Ensure the probe is placed in the desired location while avoiding contact with the surface.

Adding Your Device to a Z-Wave Network:
The leak sensor can be added to a Z-Wave network using SmartStart or manually.

SmartStart:
If your controller supports SmartStart inclusion, follow these steps:

1. Scan the Z-Wave QR code under the battery door or on the package.
2. The sensor will be added automatically within 10 minutes when powered in range of the Z-Wave network.

Manual Mode:

1. Follow your Z-Wave controller’s instructions to add the sensor to the network.
2. Remove the top cover of the sensor and ensure correct battery installation.
3. Press and release the programming button to start the manual add process.
4. Follow the LED indicators for network connection confirmation.
5. If prompted, enter the S2 security code using the provided DSK PIN.
6. Secure the top cover back into place once added to the network.

SPECIFICATIONS

IMPORTANT!

ZWN6310

• Power: 1 CR2 battery (included)
• Signal (frequency): 908.4/916MHz
• Wireless range (Classic): Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module
• Wireless range (Long Range): Up to 1,300ft. line of sight between the wireless controller and the closest Z-Wave receiver module
• Operating temperature range: 32–104° F (0–40° C)

For indoor use only Specifications subject to change without notice due to continuing product improvement

FEATURES

Get to know your Z-Wave device

• Z-Wave certified for simple pairing and integrated home automation
• Transmits notifications to the connected controller when water leaks are detected
• Dual-detection options — contacts on the sensor base or separate plug-in detection probe for hard-to-reach locations
• RGB LED indicates programming changes and status
• Alarm for separate audible notification of leaks
• Supports association with up to five devices
• Easy auto pairing and button-press settings
• This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave-enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.ezzwave.com/config

1. LED – RGB behind cover
2. Programming button
3. Sensor port
4. Sensor base – use with detachable probe
5. Battery and battery tab
6. Locking tabs
7. Alarm siren
8. Top cover
9. Detachable probe S2 security label/SmartStart QR code

INSTALLATION

The smart water leak sensor is designed for indoor use only. Place the sensor near the area of potential leaks or water source — sinks, commodes, dishwashers, washing machines, hot water tanks, etc. The sensor can be placed on the floor, cabinet base, etc. to allow the three pins on the bottom to contact the water leak. The pins contact the surface (see FIGURE 1).

For hard-to-reach areas, mount the sensor base to a wall using the double- sided tape and/or the included screw and drywall anchor (see FIGURE 2). Connect the sensor to the base noting the alignment arrows (see FIGURE 3). Insert the detachable probe in
the sensor port (see FIGURE 4). Place the end of the probe in the desired location. The contact pins are recessed to avoid contacting the surface (see FIGURE 5).

ADDING YOUR DEVICE TO A Z-WAVE NETWORK

The leak sensor can be added to the Z-Wave network using SmartStart or manually. For best results, add the sensor to the network near the intended location (same room or area) to ensure best communication routes are established.
SMART START
This sensor is SmartStart enabled. If your controller supports SmartStart inclusion, this sensor can be added into a Z-Wave network by following the instructions for your controller or hub and scanning the Z-Wave QR code under the battery door or on the package when instructed. No further action is required, and the sensor will be added automatically within 10 minutes of being powered while in range of Z-Wave network.

MANUAL MODE

1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.

2. Once the controller is ready to add your device, remove the top cover of the sensor (see FIGURE 7)

3. Ensure battery is installed with the correct polarity and the battery tab has been removed.

4. Press and release the programming button (see FIGURE 6). This starts the manual add process. The blue LED flashes quickly as it searches for a network. When the sensor is joined to the network the green LED lights for 2 seconds. After 25 seconds, the blue LED will stop flashing if the sensor is not added to the network.

5. The controller’s app will indicate if it discovers the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box or the QR code label on the product (see below).
   Enter the 5-digit code.

6. The green LED will activate for two seconds to confirm the sensor has been added in the network.

7. Secure the top cover into place.

NOTE: Your controller may need to be within 10ft. of the sensor to be added. Using the controller, you have the ability to activate groups, scenes, schedules and interactive automations when the sensor detects a leak or temperature or humidity changes. Functions may vary depending on gateway or controller.

TO REMOVE THE SENSOR FROM THE Z-WAVE NETWORK

1. Follow the instructions for your Z-Wave certified controller to remove the sensor from the Z-Wave network.
2. Once the controller is ready to remove your sensor, press and release the programming button once on the sensor (see FIGURE 6).
3. The green LED will light for 2 seconds to indicate it has been removed. Secure the top cover.

TO RESTORE FACTORY DEFAULTS AND REMOVE SENSOR FROM Z-WAVE NETWORK

1. Remove the battery.
2. Press and hold the programming button while installing the battery and continue pressing for three seconds.
3. The red LED activates for two seconds, followed by three quick flashes to confirm the sensor has been reset. Secure the top cover into place.

NOTE: This should only be used if your network’s primary controller is missing or otherwise inoperable.

TO REPLACE BATTERY

1. Remove the top cover (see FIGURE 7).
2. Remove old battery and replace with new battery (see FIGURE 8). When installing new battery, ensure proper polarity.
3. Secure top cover.

WARNING

• FOR INDOOR USE ONLY
• BATTERY MAY LEAK HARMFUL LIQUIDS OR IGNITABLE MATERIALS OR EXPLODE CAUSING INJURY AND PRODUCT DAMAGE
• KEEP BATTERIES AWAY FROM CHILDREN
• REPLACE EXHAUSTED BATTERY IMMEDIATELY
• REMOVE BATTERY IF PRODUCT IS TO BE UNUSED FOR EXTENDED PERIODS
• DO NOT USE Z-WAVE DEVICES TO CONTROL ELECTRIC HEATERS OR ANY OTHER APPLIANCES WHICH MAY PRESENT A HAZARDOUS CONDITION DUE TO UNATTENDED OR UNINTENTIONAL OR AUTOMATIC POWER ON CONTROL
• Z-WAVE-ENABLED DEVICES SHOULD NEVER BE USED TO SUPPLY POWER TO OR CONTROL THE ON/OFF STATUS OF MEDICAL OR LIFE-SUPPORT EQUIPMENT

WARRANTY

Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7 AM–8 PM, M-F, Central Time or
www.byjasco.com if the unit should prove defective within the warranty period.

FCC/IC

Suppliers Declaration of Conformity | Model #: 81018 | Jasco Products Co., 10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. CAN ICES-3(B)/NMB-3(B)

Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery-operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network. This device supports lifeline and notification (association group 1) supporting 5 nodes. Lifeline association supports the “device reset locally” function. Refer to the instructions of your controller for any available details on how this can be set. For product patent information, visit ww.byjasco.com/patents. All brand names shown are trademarks of their respective owners.

MADE IN VIETNAM

Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114. This Jasco product has a 5-year limited warranty. Visit www.byjasco.com for warranty details. Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483, M-F, 7 AM-8 PM Central Time. JASCO 2024 | ZWN6310 | 81018 | 03/21/24 v2

FAQ

Q: Can I use the sensor outdoors?
A: No, the smart water leak sensor is designed for indoor use only.

Q: How do I know if the sensor is successfully added to the Z-Wave network?
A: The green LED will light up for two seconds to confirm successful network addition.

References

• JascoPro Series Smart Water Leak Sensor manual (81018)
• Product Registration
• Jasco
• Patents

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>