Jasco ZW6309 smart Flood Freeze sensor User Manual

June 5, 2024
JASCO

ZW6309 smart Flood Freeze sensor
User Manual

READITSRAAT IT

Jasco ZW6309 smart Flood Freeze sensor - qr code Read instructions or watch the easy-to-follow video. Scan QR code or visit https://byjasco.com/52247i
Purchase additional items at EZzwave.com or visit your local retailer. Jasco ZW6309 smart Flood Freeze sensor -
fig

HOMEDEPOT MRS-LKEX-66AAK 50-Pint Portable Dehumidifier -
IconDO NOT RETURN THIS PRODUCT TO THE STORE
If you have any problems or questions, contact our U.S.-based Consumer Care at 1-800-654-8483, option 1, Monday- Friday, 7 AM-8 PM Central Time. For the most up-to-date product support, accessories, electronic (PDF) format manuals, and more, visit www.byjasco.com/support.

WARNING

  • FOR INDOOR USE ONLY
  • BATTERY MAY LEAK HARMFUL LIQUIDS OR IGNITABLE MATERIALS OR EXPLODE CAUSING INJURY AND PRODUCT DAMAGE
  • REPLACE EXHAUSTED BATTERY IMMEDIATELY
  • REMOVE BATTERY IF PRODUCT IS TO BE UNUSED FOR EXTENDED PERIODS
  • DO NOT USE Z-WAVE DEVICES TO CONTROL ELECTRIC HEATERS OR ANY OTHER APPLIANCES WHICH MAY PRESENT A HAZARDOUS CONDITION DUE TO UNATTENDED OR UNINTENTIONAL OR AUTOMATIC POWER ON THE CONTROL

NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT
 Z-WAVE-ENABLED DEVICES SHOULD NEVER BE USED TO SUPPLY POWER TO OR CONTROL THE ON/OFF STATUS OF MEDICAL OR LIFE-SUPPORT EQUIPMENT.
This device supports lifeline and notification (association group 1) supporting 5 nodes. Lifeline association supports the “device reset locally” function. Refer to the instructions of your controller for any available details on how this can be set.
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state.
Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7 AM — 8 PM, M-F, Central Time, or www.byjasco.com if the unit should prove defective within the warranty period.

Jasco Products Company LLC, Building B 10 E.
Memorial Rd. Oklahoma City, OK 73114.

SPECIFICATIONS

Power: 1 CR123A battery (included), micro USB power 5V/500mA (not included)
Signal (frequency): 908.4/916MHz
Z-Wave Range: Up to 150ft. line of sight between the wireless controller and the closest
Z-Wave receiver module
Operating temperature range: 32-104° F (0-40° C)
For indoor use, only Specifications are subject to change without notice due to continuing product improvement

Accessories

Jasco ZW6309 smart Flood Freeze sensor - fig 1

To purchase compatible accessories, visit www.byjasco.com/USB

Getting to know your new Z-Wave device

  • Z-Wave certified for simple pairing and integrated home automation
  • Transmits notifications to the connected controller when water leaks or changes in area temperature are detected
  • Dual-detection options — contacts on the sensor base or separate plug-in detection probe for hard-to-reach locations
  • Red LED indicates programming changes and status
  • Alarm for audible notification of leaks
  • Supports association with up to five devices
  • Easy auto-pairing and button-press settings
  • Automatic tamper switch with alarm
  • Regular temperature and battery level reports

Jasco ZW6309 smart Flood Freeze sensor - fig 2

NOTE: The smart flood/freeze sensor has two power options battery (included) or USB (adapter and cable sold separately).
When powered by batteries, the signal repeater function is disabled to conserve battery life. When powered by USB, the signal repeater function is active and extends your Z-Wave network.
NOTE: The signal repeater function is determined when the product is added to the network. If the power option is changed, the sensor must be removed, manually reset, and added to the network under the new power option. If a manual reset is not performed, the signal repeater function will not be updated. See section 4 for the manual reset method.
Jasco ZW6309 smart Flood Freeze sensor - fig 3 A. LED – red behind Cover
B. Programming button
C. Sensor port
D. Micro USB cable port
E. Battery and the battery tab
F. Top cover locking tab slot
G. Alarm siren
H. Top cover
I. Detachable probe.
J S2 security labeV SmartStart OR code

Installation

The smart flood/freeze sensor is designed for indoor use only. Place the sensor (typically in battery power mode) near the area of potential leaks or water sources — sinks, commodes, dishwashers, washing machines, hot-water tanks, etc. The sensor can be placed on the floor, cabinet base, etc. to allow the three pins on the bottom to contact with the water leak. The contact pins are recessed so they do not contact the surface (see figure 1). The sensor can be safely placed onto a metal surface without activating the sensor. Mounting tape (included) can be applied to the bottom of the sensor for secure placement (see figure 2).
Jasco ZW6309 smart Flood Freeze sensor - fig 5For hard-to-reach locations, use the mounting tape to attach the sensor to the wall. Open the sensor port to insert the detachable probe (see figure 3). Secure with the pins pointed down using smaller mounting tape (included) (see figure 4). The contact pins are slightly recessed so they do not contact the surface (see figure 5).
Jasco ZW6309 smart Flood Freeze sensor - fig 4
For continuous power, connect an optional micro USB cable to the power port and plug it into any 5V USB power supply (see figure 6). Optional USB cable and power supply are available at ezzwave.com.

Adding your sensor to a Z-Wave network

The flood/freeze sensor can be added to the Z-Wave network automatically or manually, from battery or micro USB power. For best results, add the sensor to the network near the intended location (same room or area) to ensure the best communication routes are established.
SmartStart
This sensor is SmartStart enabled. If your controller supports SmartStart inclusion, this sensor can be added to a Z-Wave network by following the instructions for your controller or hub and scanning the Z-Wave QR Code under the battery door or on the package when instructed. No further action is required, and the sensor will be added automatically within 10 minutes of being powered up while in range of the Z-Wave network.
Jasco ZW6309 smart Flood Freeze sensor - fig 6

Manual mode
Battery power/micro USB power

  1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.
  2. Once the controller is ready to add your device, remove the top cover of the sensor (see figure 7).
  3. Ensure the battery is installed with the correct polarity and the battery tab has been removed (see figure 8) or ensure micro USB is plugged into a USB port (see figure 9).
  4. Press and release the programming button (see figure 10). This starts the manual add process. The red LED flashes quickly as it searches for a network. After 25 seconds, the LED will stop flashing if the sensor is not added to the network. Press the programming button to manually start the add process. If it times out, the LED will stop flashing. Press and release the programming button again.
  5. The controller’s app will indicate if it discovers the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box or the QR code label on the product (see below).
    Enter the 5-digit code.Jasco ZW6309 smart Flood Freeze sensor - qr code
1| Jasco ZW6309 smart Flood Freeze sensor - qr
code 3
    ---|---
    DSK : XXXXX-25651-22671-26939-47599 -19612-25872-47752| https://byjasco.com /HEP-ET/20000-99999/39339
  6. The red LED will activate for three seconds to confirm the sensor has been added in the network.
  7. Secure the top cover into place. Note: Your controller may need to be within 10ft. of the sensor to be added. Using the controller, you have the ability to activate groups, scenes, schedules, and interactive automation when the sensor detects a leak or temperature change. Functions may vary depending on the gateway or controller.

To remove the sensor from the Z-Wave network

  1. Follow the instructions for your Z-Wave certified controller to remove the sensor from the Z-Wave network.
  2. Once the controller is ready to remove your sensor, press and release the programming button one time on the sensor (see figure 10).
  3. The red LED will blink five times to indicate it has been removed. Secure the top cover.

To return the sensor to factory defaults and remove the sensor from the Z-Wave network

  1. Press the programming button 10 times within six seconds (the interval between presses of the button cannot be longer than one second).
  2. The red LED will activate for two seconds, followed by three quick flashes to confirm the sensor has been reset. Secure the top cover into place.
    Note: This should only be used if your network’s primary controller is missing or otherwise inoperable.

To replace battery

  1. Remove the top cover (see figure 7).
  2. Remove the old battery and replace it with the new battery. When installing the new battery, ensure proper polarity.
  3. Secure top cover.

Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and applications. All non- battery-operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network.
FCC/AC
This device complies with Part 15 of the FCC and Industry Canada license- exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void the user’s authority to operate the device.
Responsible Party – US Contact Information I Parte responsible – Information de Contacto de Los Estados Unidos I Partie responsible – Coordonnees des Etats-Unis FCC — U2ZZW6309 I IC: 6924A-ZW6309 Jasco Products Company I 10 E. Memorial Rd., Oklahoma City, OK 73114 11-800-654-8483 CAN ICES-3(B)/NMB-3(B)
All brand names shown are trademarks of their MADE IN CHINA/FABRIQUE EN CHINUHECHO EN CHINA
respective owners.

DISTRIBUTED BY JASCO PRODUCTS COMPANY LLC,
10 E. MEMORIAL RD., OKLAHOMA CITY, OK 73114.
JASCO 2020 1 52247 I ZW6309 I 06/30/20 v1

Documents / Resources

| Jasco ZW6309 smart Flood Freeze sensor [pdf] User Manual
ZW6309 smart Flood Freeze sensor, smart Flood Freeze sensor, Freeze sensor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals