MXN22C-130-TVI Autoheated HD-TVI Color Ball Camera Instruction Manual
- June 3, 2024
- MXN
Table of Contents
22C-130-TVI Auto heated HD-TVI Color Ball Camera
Instruction Manual
◈ Features
- 2.07 Mega pixels Full HD SONY CMOS Color camera
- 1/2.8” Color CMOS high resolution image sensor (STARVES)
- HD-TVI 4.0, 1080P/30 fps
- IP69K Waterproof Rating
- Built-in Infra Red LEDs
- IR LED ON/OFF function (via loop wire)
- Diagonal 130˚ viewing angle
- Normal/Mirror Image adjustable
- Built-in Microphone (for one-way audio)
- Multi purpose (Front view, Side view, Rear view, Surveillance, etc)
- Built-in Automatic Heater (below +10˚C)
- Anti-corrosive 3-fold coating
- Temp. -40˚C ~ +80˚C
- Vibration resistant (10G)
- Waterproof screw type connector, 4-pin mini-DIN
- ECE R10.05 approved (EMC)
Optional versions of model MXN22C-130-TVI:
MXN22C-160-TVI 160˚(D) x 133˚(H) x 69.0˚(V)
MXN22C-078-TVI 78˚(D) x 70.0˚(H) x 39.0˚(V)
MXN22C-040-TVI 40˚(D) x 37.0˚(H) x 22.0˚(V)
MXN22C-020-TVI 20˚(D) x 19.0˚(H) x 13.0˚(V)
E9 10R-05-6368
- Front View
- Rear View
◈ Contents
◈ Technical Specifications
| Image Sensor | 1/2.8” SONY CMOS Sensor (STARVES) |
|---|---|
| Effective Pixels | 2.07 Mega pixels 1920(H) X 1080(V) |
| Resolution | 1080 TV lines |
| S/N ratio | Minimum 45 dB (at AGC off) |
| Scanning System | Progressive |
| Video Output | HD-TVI 4.0, 1080P/30 fps |
| Minimum illumination | 0 Lux (IR LEDs on) |
| Power range | DC 9 ~ 48V |
| Power consumption | DC 12V, 265 mA (heater on) |
DC 12V, 165 mA (heater off)
Operating temperature| -40ºC to +80ºC
Viewing angle| 130˚(Diagonal) x 120˚(Horizontal) x 66˚(Vertical)
Dimensions| Ø 52 mm, 72(W) x 52(D) x 63(H) incl. bracket
Weight| Approx. 215 g
Supplied Accessories| Camera Bracket: (1)
Stainless M6 x 25mm bolt + M6 nut: (2 + 2)
Stainless M3 x 12mm bolt + M3 nut: (2 + 2)
Stainless M4 x 16mm tapping screw: (2)
Rubber washer + stainless metal washer: (2 + 2)
Rubber O-Ring: (2)
Allen wrench 3mm: (1)
◈ Installation
Camera Assembly
Fix the supplied camera bracket to the vehicle.- Fix the bracket with camera according to drawing.
- Adjust the viewing angle of the camera and fasten the screws firmly.
Cable grommet
Drill a suitable hole (approx. Ø 19 mm) and insert the cable grommet.
Just before final fixation, please apply a proper sealant (for prevention)
between the hole and the grommet and also between the cable and the grommet.
Securing cable connection
- Match the arrow marks and press the connectors together.
- Screw the camera connector up clockwise.
- Tighten cable connection firmly in order to prevent water ingress.
Note!
The warranty will not be valid if the problem is related to moist/corrosion in
the connector.
Wiring to Monitor
Run the cable from the camera to the monitor.
IR LED ON/OFF function
IR LED function can be ON or OFF via the GREEN loop wire:
- Green loop wire uncut : IR LED function => ON / Standby
- Green loop wire cut : IR LED function => permanent OFF
Caution !!
-
Before making the connection, disconnect the ground terminal from the battery to avoid short circuits.
-
The plugs should be fully inserted into the connectors or jacks.
A loose connection may cause malfunctioning of the unit. -
A damaged cable may affect the operation of the camera and may even cause a malfunction of the camera or monitor: Avoid a damaged cable!
-
Protect the cable by using a guide tube, pipe or run the cable inside the vehicle as much as possible. Caution! Run the cable in natural shapes in order to prevent cable breaks.
-
Preferably use an acid free grease in between the waterproof screw type connectors and tighten them firmly each other.
- Design And Specifications Are Subject To Change Without Notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>