MXN204-TVI HD Multi-Purpose Camera Control Box Owner’s Manual

MXN204-TVI HD Multi-Purpose Camera Control Box

PACKAGE CONTENTS

| |
---|---|---
CONTROL BOX| POWER CABLE| RCA CABLE

| |
REMOTE CONTROLLER| IR RECEIVER| MANUAL
|

|

CABLE BRACKET| CABLE BRACKET SCREW| MOUNT SCREW
CONTROL BOX| 1
---|---
POWER CABLE| 1
RCA CABLE| 1
REMOTE CONTROLLER| 1
IR RECEIVER| 1
MANUAL| 1
CABLE BRACKET| 2
CABLE BRACKET SCREW ( FH M3X5 )| 4
MOUNT SCREW ( PH M4X30 STAINLESS)| 4

INSTALLATION

• Bracket Cable
• Fix the bracket jack with provided screw after connecting the cameras
• Mounting on the floor, console, etc

CONNECTION

Power & Trigger wire connection

Loop OUT

OPERATION

Remote Controller

1. POWER button
   Press the POWER button to turn the control box on or off.
   When a trigger signal is activated, the control box does not Respond to the remote control’s signal.
   (Please refer to TRIGGER MODE in MAIN MENU for further information)
   Status of RED LED in IR Receiver
   STANDBY: LED ON
   POWER ON: LED OFF
   IR SIGNAL: LED BLINK
   

2. MENU button
   Press MENU button for control box setting

3. UP/DOWN button
   Press UP/DOWN button for moving MENU

4. LEFT(VOL-)/RIGHT(VOL+) button
   Press LEFT/RIGHT button to change MENU when MENU is on
   Press LEFT/RIGHT button to control volume up and down when MENU is off

5. QUAD button
   Press QUAD button to display SPLIT4 of CAMERA input or BNC input

6. ENTER button
   Press ENTER button to select MENU when MENU is on
   Press ENTER button to change display mode as below sequence when MENU is off CH1 → CH2 → CH3 → CH4 → SPLIT1 → SPLIT2 → TRIPLE → QUAD → CH1…

7. QUAD button
   Press QUAD button to display SPLIT4 of CAMERA input or BNC input

8. F1 button
   Press F1 button to select HDMI input

9. F2 button
   Press F2 button to select VGA input

10. F3 button
    Press F3 button to select RCA input

MENU TREE
Change the setting value by pressing the MENU button.

• FUNCTION
  Set functions on the monitor.

• PICTURE
  Set the color and brightness on the monitor.

• NORMAL/MIRROR
  Input video can be reversed

• AUDIO
  Set the audio ON/OFF.

• TRIGGER AUDIO
  Set the audio ON/OFF when entering the TRIGGER signal.

• CAMERA TRIGGER
  When entering the TRIGGER signal, the screen output.

• DISTANCE MARKER
  DISTANCE MARKER can be set according to the TRIGGER signal input.

• AUTO PICTURE SCAN
  Set the automatic sequence switching time.

• CAMERA NAME
  Set the camera name.

• SPEED SWITCH
  By receiving TACHO signal, you can set the operation at the corresponding frequency.

• SPLIT
  Display the camera video at the set position on the SPLIT screen.

• TRIPLE
  Display the camera video at the set position on the TRIPLE screen.

• QUAD
  Display the camera image on the QUAD screen at the set position.

• MANUAL SELECTION
  When the SELECTION button is pressed, the output screen is set.

FUNCTION

• LANGUAGE
  Provide 6 Multi-lingual OSD [ENGLISH, SWEDISH, DANISH, NORWEGIAN, DUTCH, FINNISH]. Select the preferred LANGUAGE.

• SYSTEM
  Select AUTO/TVI/AHD/NTSC/PAL

• VIDEO OUT
  Select NTSC/PAL for the video output format

• CAMERA INPUT
  Select DIN-4P/BNC for camera input

• AUTO POWER
  Select monitor activation functions as below.

• [AUTO] The Control box remembers the last settings from its memory. [ON] The Control box is turned on with the

• 『Power-ON』 mode automatically.[OFF] The Control box is turned on with the

• 『Stand-By』 mode automatically.

• RESET
  Press the “>>” button to enter the factory default settings.

• SYSTEM INFO
  Refers to the system information of the monitor.

• PICTURE MENU

• Press the [LEFT/RIGHT] button to adjust the PICTURE of the monitor.

• PICTURE MENU is for the settings of PICTURE from CAM1, CAM2, CAM3, CAM4, SPLIT1, SPLIT2, TRIPLE, and QUAD modes.

• NORMAL/MIRROR
  Each camera (CAM1/CAM2/CAM3/CAM4) can be switched between NORMAL& MIRROR image.

• AUDIO
  Audio ACTIVATED Mode in normal mode.
  When the mode is [ON], audio will be on (activated) When the mode is [OFF], audio will be off (mute).

• TRIGGER AUDIO
  Audio ACTIVATED Mode in Trigger mode. Choose the trigger and then press [ENTER]. The Audio settings menu will be shown as below.

• When the mode is [ON], audio will be on(activated).
  When the mode is [OFF], audio will be off (mute). The user can adjust the volume.

• CAMERA TRIGGER

• TRIGGER 1/2/3/4 (Trigger source selection)

• Select the required trigger source at CAM1/CAM2/CAM3/CAM4/SPLIT1/ SPLIT2/TRIPLE / QUAD

• REMARK
  TRIGGER PRIORITY: TRIGGER 1 > TRIGGER 2 > TRIGGER 3 > TRIGGER 4

• DISTANCE MARKER
  Select ON to have a DISTANCE MARKER for CAM1, CAM2, CAM3, and CAM4. DISTANCE MARKER is displayed as the trigger signal is activated

• MARKER

• Select DISTANCE MARKER.or ___

• DISTANCE MARKER ADJUSTMENT
  Users can make adjustments by pressing the SELECT button in the menu. (It is not available on the split mode screen)

• Marker A- Parking line

• The left/right/both markers will be selected in order each time you press the SELECT button. When the marker is red it can be adjusted UP/DOWN or LEFT/RIGHT.

• When both distance markers are RED, you can adjust both markers LEFT/RIGHT/UP/DOWN.

• When the left distance marker is RED, the left marker can be adjusted LEFT/RIGHT.

• When the right distance marker is RED, the right marker can be adjusted LEFT/RIGHT.

• Marker B- Horizontal line

• Users can adjust the line UP/DOWN.

• Users can adjust the horizontal line by pressing [UP/DOWN] buttons.

• AUTO PICTURE SCAN
  Each scanning time of CAM1/CAM2/CAM3 /CAM4/SPLIT1/SPLIT2/TRIPLE/QUAD can be managed.

• REMARK

• If the SCAN TIME is set as[0], the monitor skips its channel during scanning.

• Press the [UP] button for 4 seconds to ACTIVATE / INACTIVATE auto scanning function.

• CAMERA NAME
  CAMERA NAME can be selected as CAM1, 2, 3, 4/REAR/LEFT/RIGHT/FRONT.

SPEED SWITCH

The orange wire needs to be connected with the vehicle’s tacho signal and via MENU the SPEED SWITCH needs to be selected ON. At FREQUENCY 67Hz setting(and the most common used tacho signal) the selected camera will be displayed during a speed of 0~33km/h. Select the concerning camera via『UNDER FREQUENCY CAM』(At a different type of tacho signals the FREQUENCY needs to be adjusted higher or lower than the example)
Over 33km/h(72Hz) the selected camera will be switched OFF automatically. When the speed slows down, then the selected camera will be switched ON automatically again at 30km/h. Instead of automatic switch OFF at a speed over 33km/h it is also possible to activate another video source, such as a navigation picture from an optional navigation computer. In this case user needs to select 『OVER FREQUENCY DISPLAY: ON』 and user needs to select 『OVER FREQUENCY CAM』
In case of TRIGGER activation with the『SPEED SWITCH ON』 mode, then TRIGGERS 1~ 4 will nullify 『SPEED SWITCH』 function.

SPLIT CONFIGURATION

• To use CROP mode, turn it on the menu and press the ENTER (SELECT) button to display a red border on the video of the channel to be adjusted.
• You can enter the adjustment mode only in the CROP mode.
• Press the ENTER (SELECT) button to select the channel (SOURCE1,2) to be adjusted.

Horizontal SPLIT CROP

• Adjust by moving the screen to be displayed in the selected channel using the left/right keys.

Vertical SPLIT CROP

• Adjust by moving the screen to be displayed using the Up/Down keys in the selected channel.

TRIPLE CONFIGURATION

TRIPLE configuration:
SOURCE 1 Select S1 Camera(CAM1~CAM4). SOURCE 2 Select S2 Camera(CAM1~CAM4). SOURCE 3 Select S3 Camera(CAM1~CAM4).
AUDIO MODE
Select TRIPLE of Audio(CAM1~CAM4). Select TRIPLE MODE

QUAD CONFIGURATION & MANUAL SELECTION

• SOURCE 1 Select S1 Camera(CAM1~CAM4).

• SOURCE 2 Select S2 Camera(CAM1~CAM4).

• SOURCE 3 Select S3 Camera(CAM1~CAM4).

• SOURCE 4 Select S4 Camera(CAM1~CAM4).

• AUDIO Select QUAD of Audio(CAM1~CAM4).

• MODE Select QUAD MODE

• MANUAL SELECTION
  When you manually press the channel select button, only the camera selected ON and the display mode selected ON are displayed.
  Manually pressing the channel select button skips the camera selected OFF and display mode selected OFF.

• NOTE
  Triggers neglect the MANUAL SELECTION settings. In case of Trigger activation, these ON/ OFF settings will be ignored.

MENU LOCK & SCAN ON/OFF FUNCTION

• MENU LOCK ON/OFF FUNCTION

• LOCK ON/OFF FUNCTION
  The setup menu can be locked to ban any unauthorized users.

• LOCK ON mode
  At the Power-ON mode, press the [DOWN] button for 10 seconds to activate the LOCK ON function.
  When [LOCKED] is displayed on the screen, the user can use only [POWER, SELECT, VOLUME] buttons and the user can edit settings for the PICTURE menu.

• LOCK OFF mode
  At the Power-ON mode, press [DOWN] button for 10 seconds to activate the LOCK OFF function.
  When [UNLOCKED] is displayed on the screen, the user can use all the functions of the setup menu.

• SCAN ON/OFF FUNCTION
  At the Power-ON mode, press the [UP] button for 4 seconds to activate the Auto Scan Picture function.
  During the Auto Scan Mode, press the [UP] button for 4 seconds to deactivate Auto Scan Picture function.

SPECIFICATIONS

MODEL: MXN204-TVI

PAL, CVBS-NTSC
Camera Input (4-pin mini-DIN)| 4CH, Composite Video 1Vp-p 75Ω (MXN configuration)
Video Input (BNC)| 4CH, Composite Video 1Vp-p 75Ω
A/V Input (HDMI)| 1CH, Up to 2160p 50/60
A/V Input (RCA)| 1CH, Composite Video 1Vp-p 75Ω 1CH, Audio, 150mV RMS 47K
Video Input (D-Sub)| 1CH, VGA, R/G/B Video 0.7Vp-p, H/V Sync, I2C
A/V Output (HDMI)| 1CH, HDMI 1.3, 1080p 50/60
Video Output (BNC)| 4CH, Loop out, Composite Video 1Vp-p 75Ω
A/V Output (RCA)| 1CH, Composite Video 1Vp-p 75Ω 1CH, Audio, 150mV RMS 47K
Operating Temperature| -25℃ ~ +75 ℃
Storage Temperature| -30℃ ~ +85 ℃
Ambient Condition| Indoor use only
Vibration| 5.5G
Dimension| 162 (W) X 43 (H) X 140 (D) mm
Weight| 700g
Supplied Accessory| Power cable (1)

RCA cable (1)

Remote Controller (1)

IR Receiver (1)

Cable bracket (2)

Screw kits (1)

Manual (1)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>