MXN44C-MOD Moving Object Detection Camera Instruction Manual
- June 3, 2024
- MXN
Table of Contents
MXN44C-MOD Moving Object Detection Camera Instruction Manual
MXN44C-MOD Camera
Contents
Features
- Moving Object Detection Camera
- Compact size color camera with integration of MOD function.
- Compatible with MXN HD-TVI monitors w/o any control unit
- Detection of moving object (pedestrians, cyclist, vehicles, etc.)
- Audio Warning Alarm (via MXN HD-TVI monitor’s speaker)
- 2.07 Mega pixels Full HD SONY CMOS Color camera
- 1/2.8” Color CMOS high resolution image sensor (STARVIS)
- HD-TVI 1080p 30fps
- IP69K Waterproof Rating
- Multi purpose (Frontview, Sideview, Rearview, Surveillance, etc)
- Waterproof screw type connector, 4-pin mini-DIN
- Diagonal 200˚ Viewing angle
- Normal/Mirror Image adjustable (via loop wire)
- Ultra low light performance
- Automatic Electronic Iris
- Built-in Microphone (for one-way Audio)
- Temperature Range -40˚C to +80˚C
- Vibration resistant (10G)
- ECE R10.05 approved (EMC)
Moving Object Detection Function
Technical Specifications
Image Sensor : 1/2.8” SONY CMOS Sensor (STARVIS)
Effective Pixels : 2.07 Mega pixels 1920(H) X 1080(V)
Resolution : 1080 TV lines
Scanning System : Progressive
Video Output : HD-TVI 4.0, 1080P/30fps
Audio Input : High Sensitive C-Microphone
S/N ratio : Minimum 48dB (at AGC off)
Minimum illumination : 0.5 Lux (50IRE)
Power consumption : DC 12V, 200mA
Power range : DC 9 ~ 48V
Operating temperature : -40ºC to +80ºC
Viewing angle : 200˚(Diagonal) x 175˚(Horizontal) x 97˚(Vertical)
Dimensions : Ø 38mm, 59(W) x 38(D) x 50(H) incl. bracket
Weight : Approx. 107g (total weight incl. bracket : 120g)
Installation
▪ Camera Assembly
- Fix the supplied camera bracket to the vehicle.
- Fix the bracket with camera according to drawing.
- Adjust the viewing angle of the camera and fasten the screws firmly.
▪ Cable grommet
Drill a suitable hole (approx. Ø 19mm) and insert the cable grommet.
Just before final fixation, please apply a proper sealant (for prevention)
between the hole and the grommet and also between the cable and the grommet.
Securing cable connection
- Match the arrow marks and press the connectors **together.
**
- Screw the camera connector up clockwise.
- Tighten cable connection firmly in order to prevent water ingress.
Note!
Warranty will not be valid if the problem is related to moist / corrosion in the connector.
Wiring to Monitor
Run the cable from the camera to the monitor.
Normal / Mirror Image adjustment
The Normal / Mirror image can be changed via the GREEN loop wire:
- Green loop wire un-cut : MIRROR image
- Green loop wire cut : NORMAL image
Caution !!
-
Before making the connection, disconnect the ground terminal from the battery to avoid short circuits.
-
The plugs should be fully inserted into the connectors or jacks.
A loose connection may cause malfunctioning of the unit. -
A damaged cable may affect the operation of the camera and may even cause a malfunction of the camera or monitor:
Avoid a damaged cable! -
Protect the cable by using a guide tube, pipe or run the cable inside the vehicle as much as possible.
Caution! Run the cable in natural shapes in order to prevent cable breaks. -
Preferably use an acid free grease in between the waterproof screw type connectors and tighten them firmly each other.
* Design And Specifications Are Subject To Change Without Notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>