eta 418090000 Latteria Espresso Coffee Maker User Manual

eta 418090000 Latteria Espresso Coffee Maker

SAFETY WARNING

GENERAL PROVISIONS:

• Before the first use, read the instructions for use carefully, look at the picture and store the instructions for use for the future. Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
• Check whether the data on the type label correspond with the voltage in your socket. The power cord plug has to be connected to the properly connected and grounded socket according to the national standard.
• This appliance may only be used by children aged 8 years or older, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Children younger than 8 years must be kept out of reach of the appliance and its power cord.
• Children must not play with the appliance.
• Before replacing accessories or accessible parts that are moving during operation, before assembly and disassembly, before you fill the water tank, before cleaning and maintenance, before transfer, if the appliance is left unsupervised, or if you finish using it, make sure to switch OFF the appliance and unplug it from the mains by pulling the plug from the socket!
• Before you remove any accessible parts, before maintenance and handling, allow the appliance and any parts thereof to cool down.
• CAUTION – Do not use the appliance with a program, time switch or any other part that turns the appliance on automatically as there is a risk of fire if the appliance is not covered or placed properly.
• CAUTION – Some parts of this product can become extremely hot and cause burns. The appliance produces hot water, steam, and warm milk (microfoam) under pressure during operation. Special attention must be paid to the presence of children and the disabled.
• CAUTION, HOT STEAM – Take extra care when using the milk container and do not touch the metal milk nozzle until it has cooled down. Use only the E3 lever provided for this purpose to operate the nozzle during operation.
• For hygienic reasons, clean the milk tank by rinsing it after each use (especially its nozzle). After it has cooled down, remove, and disassemble the milk container and then carry out complete maintenance on all parts.
• When the appliance is in operation, prevent pets, plants or insects to get in contact with it.
• Do not plug the fork of the supply cord into the power outlet and do not unplug the cord with wet hands or by pulling by the supply cord!
• Prevent injuries when handling (e.g. by hot water, steam).
• Never immerse the appliance or its cord (or parts thereof) in water.
• Do not carry the appliance if there is water / milk in the containers! There is a risk of water / milk leaking into the internal components.
• Never leave the appliance unattended when it is connected to the mains and keep an eye on it the whole time you are making your espresso!
• When transferring the appliance, take it by the outer casing only.
• Leave a space of at least 15mm from all sides of the appliance to ensure proper circulation of air.
• Do not expose the appliance to temperatures under 4°C – if residual water froze in the internal components, it could damage the appliance.
• Use this appliance only for the purpose for which it was designed as specified in this user‘s manual. Never use the appliance for any other purpose.
• The producer is not responsible for damage caused by improper use of the appliance
  (e.g. burning, scalding, fire) and its guarantee for the appliance does not apply to situations when the safety warnings above are not complied with.

USE OF THE APPLIANCE:

• The appliance is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!

• If you are not going to use the appliance for a longer time, empty the water tank! If you do not brew coffee frequently, replace the water in the water tank regularly (preferably every day) so as to keep it fresh at all times.

• Always use only cold (lukewarm) clean water! Never use hot water. This could damage the appliance.

• Never put warm or hot milk in the milk container E. Ideally, use chilled milk straight from the fridge.

• Use the appliance in the working position only at flat and stable places with no risk of turning over and in sufficient distance from heat sources (e.g. heater, stove, cooker, oven, grill), flammable objects (e.g. curtains, drapes, etc.) and wet surfaces (e.g. sinks, wash basins, etc.).

• Do not place the appliance near objects or under objects which could get damaged by steam, e.g. walls, kitchen cupboards, sideboards, paintings, or curtains. Leaking steam could damage them.

• Do not use the appliance in an environment saturated with explosive or flammable steams.

• Before switching on the appliance ensure that the water level is between MIN and MAX marks.
  POWER CORD:

• If the power cord of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician or a similarly qualified person so as to prevent dangerous situations.

• Never use the appliance if its power cord or plug is damaged, if it does not work properly, if it fell down and was damaged or if it fell to water. In this case take the appliance to a special service to check its safety and proper function.

• The power cable supplied with the appliance is designed solely for this appliance – never use it for any other purposes. Also, this appliance may only be used with the power cable included in the box. Never use any other cable type (e.g. for a different appliance).

• Never put the power cord on hot surfaces or do not let it hang over the edge of a table or a work top. Plugging or pulling the power cord e.g. by children can result in tilting over or drawing the appliance down and serious injury!

• The power cord must not be damaged with sharp or hot objects, open fire, it must not be sunk into water or bent over sharp edges.

DESCRIPTION OF THE APPLIANCE

A – The machine body

• A1 – heating surface

• A2 – hinged lid of the water container

• A3 – hinged cup holder

• A4 – power cord
  B – Control panel

• B1 – button ON/OFF

• B2 – button for one cup

• B3 – button for two cups

• B4 – button for automatic maintenance

• B5 – button for milk frothing

• B6 – button for preparing cappuccino

• B7 – button for preparing latte macchiato

• B8 – red light

• B9 – yellow light
  C – Metal lever with plastic handle

• C1 – stainless steel bowl for one cup

• C2 – stainless steel bowl for two cups
  D – Water tank

• D1 – handle
  E – Milk container

• E1 – milk container lid

• E2 – milk nozzle

• E3 – control lever for tilting the nozzle

• E4 – rotary knob for milk frothing adjustment

• E5 – milk container lock button

• E6 – milk hose

• E7 –lid lock button
  F – D rip tray

• F1 – drip grille
  G – Coffee measuring cup with stamper

PREPARATION FOR USE

Before first use, remove any packaging and protective material (including any protective film) from the appliance and accessories. Wash containers D and E with warm water and
a suitable detergent, rinse with clean water and allow to dry. Then put them back in the coffee machine.

Location
Place the coffee machine onto a flat and stable surface, near a socket. Keep a minimum distance of 30 cm from any wall at all sides.

Filling the tank with water
Open lid A2, remove container D and fill it with water, preferably at room temperature (the water level must be between the MIN and MAX marks). Then put the tank back in place.

Filling with milk
Remove container E, remove the lid E1 and fill it with milk (the milk level must be between the MIN and MAX lines). Then put the container back in place.

Notes

• If possible, use only fresh whole milk.
• It is also possible to use alternative types of milk (soy, almond, etc.) with a label “Barista“.
•  Make sure that the E6 milk hose is correctly positioned.

Removing operational components
Looking at the camera that is used more often with the coffee machine (metal lever C, drip tray F), proceed as shown in Fig. 1. Proceed in reverse order to put the components back.

Rinsing the coffee maker
When using the coffee machine for the first time or if you have not used the coffee machine for more than 2 days, first rinse it with clean water. The procedure is as follows:

1. Fill containers D and E with water.
2. Place lever C correctly in place.
3. Place a suitable container under the coffee spout and the milk nozzle.
4. Switch on the coffee machine by pressing button B1 and wait for it to warm up. The heating of the coffee machine is indicated by the flashing of the light signalling of buttons B2-B7. The light in button B1 illuminates red.
5. Press and hold button B4 (for approx. 3 seconds) and wait for the first cleaning step to complete.
6. Then press the B4 button again, but this time briefly and wait for the second cleaning step to complete.

USING THE APPLIANCE

Remarks

• Pressing any button is accompanied by an acoustic signal.
• When making coffee, the coffee machine automatically has a coffee brewing function that cannot be switched off.
• The heating of the coffee machine is indicated by the flashing of the light signalling of buttons B2-B7. The light in button B1 illuminates red.
• If you remove the milk container E, only the espresso function (buttons B2 and B3) can be used.
• Automatic shut-off after 30 minutes of inaction.

PREPARATION OF ESPRESSO

1. Switch on the coffee machine by pressing button B1 and wait for it to warm up.
2. Fill the container D with water.
3. Fill the stainless-steel bowl (C1/C2) with ground coffee to the brim with a measuring cup G. Smother the coffee properly with the stamper (back of the measuring cup G) intended for this purpose.
4. Place the lever C on the coffee machine as shown in Fig. 3.
5. Place a suitable size cup / cups under the coffee spout.
6. Press button B2 (for one cup – factory setting 32 ml) or button B3 (for two cups – factory setting 62 ml). The indicator light of the relevant button will flash during preparation.
7. Wait for the coffee to finish (an acoustic signal sounds).

Cup preheat

• For an optimum coffee making process and better taste of your coffee, we recommend that you preheat your cup by filling it with hot water first (e.g. using the hot water function). After the cup has been preheated, pour the water away.
• You can use the heating surface A1 to warm up the cup for your coffee.

PREPARATION OF CAPPUCCINO AND LATTÉ MACCHIATO
You can prepare cappuccino and latte macchiato using the pre-set automatic programs (buttons B6 and B7). It is also possible to use the method of preparation using a separate milk frothing function (button B5).

Note
You can use the E4 rotary knob to set the ratio between the amount of hot milk and milk foam:

• If you want more milk foam, turn the E4 knob to the right.
• If you want more hot milk, turn the E4 knob to the left.

Using pre-set automatic programs:

1. Switch on the coffee machine by pressing button B1 and wait for it to warm up.
2. Fill the D container with water and the E container with milk.
3. Fill the stainless-steel bowl (C1/C2) with ground coffee to the brim with a measuring cup G. Smother the coffee properly with the stamper (back of the measuring cup G) intended for this purpose.
4. Place the lever C on the coffee machine as shown in Fig. 3.
5. Press the B6 button (final beverage volume will be approx. 137 ml) or B7 button (final beverage volume will be approx. 273 ml) The indicator light of the relevant button will flash during preparation.
6. Wait for the beverage preparation to complete (an acoustic signal sounds).

Preparation of Cappuccino and Latté Macchiato using a separate milk frothing function:

1. Switch on the coffee machine by pressing button B1 and wait for it to warm up.
2. Fill the D container with water and the E container with milk.
3. First, prepare the coffee using the classic method (see paragraph ESPRESSO PREPARATION).
4. Then press the B5 button. The indicator light of the B5 button will flash during preparation.
5. Wait for the milk to froth (an acoustic signal sounds).

INDIVIDUAL COFFEE MACHINE SETTINGS

INDIVIDUAL SETTING – ESPRESSO
The amount of coffee can be adjusted for both one cup (32-48 ml – button B2) and two cups (62-78 ml – button B3). The procedure is as follows:

1. Switch on the coffee machine by pressing button B1 and wait for it to warm up.
2. Fill container D with water.
3. Then press and hold the B2/B3 button (an acoustic signal sounds) until the required amount of coffee flows out. When the required amount of coffee has flowed, release the button pressed (an acoustic signal sounds).
4. The setting will be saved in the coffee machine memory and will remain stored even after the coffee machine is switched off and unplugged. network.

Remark
If you hold the B2/B3 button too short, your settings will not be saved.

INDIVIDUAL SETTING – CAPPUCCINO AND LATTÉ MACCHIATO
The amount of coffee can be set between 32-48 ml and the amount of milk (foam) can be set between 105-165 ml / 247-373 (B6/B7). The procedure is as follows:

1. Switch on the coffee machine by pressing the B1 button and wait for it to warm up.
2. Fill the D container with water and the E container with milk.
3. Press B6/B7 and wait for the milk foam to start flowing. Then press and hold the appropriate button (an acoustic signal sounds). When the required amount of foam has flowed, release the button pressed (an acoustic signal sounds). Then wait until the coffee starts to flow. Then press and hold the appropriate button again (an acoustic signal sounds). When the required amount of coffee has flowed, release the button pressed (an acoustic signal sounds).
4. The settings will be saved in the coffee machine‘s memory and will remain saved even after the coffee machine is switched off and disconnected from the power supply.

INDIVIDUAL ADJUSTMENT OF MILK AMOUNT
The amount of milk (foam) can be set between 128-195 ml. The procedure is as follows:

1. Switch on the coffee machine by pressing the B1 button and wait for it to warm up.
2. Fill the D container with water and the E container with milk.
3. Then press and hold button B5 (an acoustic signal sounds) until the required amount of milk (foam) flows (an acoustic signal sounds).
4. The settings will be saved in the coffee machine’s memory and will remain saved even after the coffee machine is switched off and disconnected from the power supply.

FACTORY SETTING RESET
If you wish to cancel the coffee machine settings that you have modified, you can return it to the factory setting. The procedure is as follows:

1. Switch the coffee machine off by pressing the B1 button.
2. Press and hold the B2 and B3 buttons at the same time. Then switch the coffee machine on while holding both buttons by pressing the B1 button. The indicator light on the control panel flashes and an acoustic signal sounds..
3. Release the B2 and B3 buttons.
4. Now the factory setting of the coffee machine is restored.

LIGHT INDICATION

B8

|

red

| flashing| There is no water in the container.
stably lighting| The coffee machine is damaged, contact an authorized service centre.

B9

|

yellow

|

flashing

| Warning of the need to descale the coffee machine. See Chapter VII. MAINTENANCE for the descaling procedure.

 MAINTENANCE

Unplug the appliance from power supply by taking the fork of the power cord out of the socket (except for operations which require the coffee machine to remain switched on)! Clean the appliance only when it is cooled down! Do not use rough and aggressive detergents (e.g. sharp objects, scrapers, diluting agents or other solvents)! Wipe the surface of the appliance and its inlet with a damp cloth.

IMPORTANT
Regularly inspect and clean all parts to prevent mould on coffee residues!

Water tank (D)
We recommend that you clean the tank thoroughly and regularly (about once a week). Use regular washing-up liquid and then rinse the tank with clean water (you can also use a dishwasher). So as to prevent build-up of scale deposits, we recommend that you also rinse the tank under running water once a day.

Milk container (E)
Clean the container immediately after each use! To wash the plastic part E, use a classic dishwashing detergent and then rinse thoroughly with clean water (you can also use a dishwasher). Wipe the surface of lid E1 with a damp cloth. Do not immerse the E1 lid in water! Use the automatic program to clean the inside of the lid and the milk nozzle. The procedure is as follows:

1. Switch on the coffee machine by pressing the B1 button and wait for it to warm up.
2. Fill tank E with water up to the MAX line.
3. Place a suitable container under the E2 milk nozzle.
4. Briefly press the B4 button.
5. Wait for the automatic maintenance program to complete.

Metal lever with plastic handle (C)
Remove coffee grounds from the stainless steel bowls (C1 and C2) after each use. Rinse the funnel thoroughly under running water. Wash the filters (C1 and C2) in warm water with detergent and then rinse with clean water. Wipe the plastic handle with a damp cloth. Then let everything dry.

Drip tray (F)
Pour the drip tray as required. Wash parts F and F1 with a conventional dishwashing detergent, rinse with clean water and allow to dry.

Descaling
If the coffee preparation time is significantly prolonged, the coffee machine‘s water system must be cleaned of lime and mineral deposits (scale). Said deposits may be removed with a water solution with a formulation intended for this purpose (e.g. ETA518000201). Always follow the manufacturer‘s instructions for the product, which are usually on the packaging. Depending on the water hardness and the frequency of use of the coffee machine, remove scale regularly (recommended at least once a month). The procedure is as follows:

1. Fill containers D and E with prepared cleaning solution.
2. Position lever C correctly.
3. Place a suitable container under the coffee spout and the milk nozzle.
4. Press and hold button B4 (for approx. 3 seconds) and wait for the first cleaning step to complete.
5. Then press the B4 button again, but this time briefly and wait for the second cleaning step to complete.
6. After emptying both containers (D and E), rinse them with clean water. Then fill both containers with clean water only and repeat the whole procedure. This will thoroughly flush the inside of the coffee machine from the cleaning solution.

Expert service must do the large maintenance or to intervene into inside parts of the appliance! Non-observance of the instructions of the manufacturer cancels the right for guarantee repair! If you are unable to fix the problem, or if you need any further information about the appliance or service centres, please contact your distributor.

ENVIRONMENT

Printed signs of materials used for manufacture, packing, components and accessories, as well as their recycling, are on all the pieces if their dimensions enable it. The symbols on the product or in the accompanying documentation mean that the used electric
or electronic products must not be disposed together with municipal wastes. Please, hand them over to the collection points designed for their correct disposal, where they will be accepted free of charge. By correct disposal of this product you can help to preserve valuable natural resources and help to prevent possible negative impacts to the environment and to human health, which could be the results of incorrect waste disposal. For further details ask the municipal authorities or the nearest collecting point. Penalties can be charged for incorrect disposal of such wastes, according to national regulations. If the appliance is to be put out of operation definitely, we recommend cutting off the feeder cable, to disable its use.

TECHNICAL DATA

• Voltage (V) shown on the type label of the appliance
• Absorbed power (W) shown on the type label of the appliance
• Max. volume (ml) 1400/390
• Weight (kg) approximately 4.2
• Protection class of the appliance I.
• Size (mm): 210 x 280 x 310
• Input in off mode is <0,50 W

The manufacturer reserves the right to change the technical specifications and accessories for the respective models.
WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE INSTRUCTIONS MANUAL:
HOUSEHOLD USE ONLY; DO NOT IMMERSE IN WATER OR OTHER LIQUIDS; TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

References

• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• ElektroEko – Odbiór odpadów elektro
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>