MONOBLOCK MSI Mag Z690 Torpedo Ek X D-RGB User Guide

June 3, 2024
EK

EK logo Mana MSI MAG Z690 TORPEDO EK X D-RGB
MONOBLOCK
User Guide

MONOBLOCK MSI Mag Z690 Torpedo Ek X D-RGB

This product is intended for installation only by expert users.
Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
Please carefully read the manual thoroughly before beginning with the installation process!
Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).
The EK- Fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.
The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

BOX CONTENTS

MONOBLOCK MSI Mag Z690 Torpedo Ek X D RGB - BOX
CONTENTS

PREPARING YOUR MOTHERBOARD

MONOBLOCK MSI Mag Z690 Torpedo Ek X D RGB -
MOTHERBOARD APPLYING THERMAL COMPOUND
Apply thermal compound on CPU heat spreader (IHS) with enclosed EK-TIM Ectotherm thermal grease. The quantity of about two rice grains is just about right. There is no need to cover the whole IHS.
Applying too much thermal grease will have negative impact on the cooling performance!
CUTTING THERMAL PADS
1. Thermal PAD F 1.5mm – (120 x 16 mm) EAN: 3830046996749
WARNING: Dimensions on pictures below are scaled.
PLACING THERMAL PADS ON THE MONOBLOCK
Place thermal pads on Monoblock as shown on the picture.
Please remove the protective foil from both sides of the thermal pads prior to installation!

PLACING THE BLOCK ON TO MOTHERBOARD

MONOBLOCK MSI Mag Z690 Torpedo Ek X D RGB - PLACING THE
BLOCK

STEP 1
Place the Backplate Insulator (Rubber Gasket) and Metal Backplate under the motherboard and make sure the mounting holes are aligned with those on the rubber gasket and metal backplate.
Use four (4) M4 PVC washers and Magnitude Z690 Torpedo Standoff (Ni) and screw them into the motherboard.
Place the EK-Mana MSI MAG Z690 TORPEDO EK X D-RGB water block to the motherboard (as shown on the photo). Make sure that mounting holes are aligned.
Prior to fastening the screws please make sure the mounting holes on the motherboard’s circuit board are aligned with the water block.
Put the springs in the holes, and then use four screws to tighten Monoblock on to the motherboard. Do not use excessive force when tightening the screws.
ATTACHING BLOCK ON THE MOTHERBOARD
STEP 1
Do not forget install the Backplate Insulator and Backplate (as shown on the photo).
For the EK-Mana MSI MAG Z690 TORPEDO EK X D-RGB series water block to operate properly the G1/4 port nearest to the right edge of the water block MUST BE USED AS THE INLET PORT.
EK recommends the use of EK-Fittings. When using fittings other than EK series please use hose clamps or appropriate substitute to secure the tubing to the barb. The use of biocide containing and corrosion inhibiting coolant is always recommended for any liquid cooling system.

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS

MONOBLOCK MSI Mag Z690 Torpedo Ek X D RGB - BLOCK
PARTS

Position EAN Description Quantity
1 9028 Vijak M4 x 14 7991DIN – Nickel 4
2 102663 Vijak M3 x 10 7991DIN (Black Nickel) 11
3 104027 Baker – Velocity 2 1700 1
4 104029 Kovina – Velocity 2 Jet Plate 1700 1
5 104247 Kovina – MSI Z690 Torpedo 1
6 104246 TOP Plexi – MSI Z690 Torpedo 1
7 104510 Cover – MSI Z690 Torpedo EK X 1
8 104309 OR 7 x 1.5 1
9 5192 OR – MSI Z690 Torpedo EK X 1
10 104308 EK – Meta Badge 1
11 103951 OR – Velocity 2 Set 1

CONNECTING THE D-RGB LED STRIP

Plug the 3-pin connector from Monoblock D-RGB LED strip to the motherboard.
Please ensure that the arrow indicated on the connector is plugged into the +5V line as indicated on your motherboard.
Failure to do so will damage your motherboard or LED strip.
REQUIRED TOOLSMONOBLOCK MSI Mag Z690 Torpedo Ek X D RGB - REQUIRED
TOOLS

SUPPORT AND SERVICE

In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “TECHNICAL
SPECIFICATIONS AND PRODUCT PARTS” where you can find the EAN number of each part you might need.
Include the EAN number with quantity in your request. Mounting
Mechanism EAN can be found under “BOX CONTENTS”
Thermal pads are readily available in the EK shop

SOCIAL MEDIA
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
EKWBofficial
ekwaterblocks
EK logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals