EK-Quantum 3831109901687 Velocity UNC Standoffs User Guide
- June 9, 2024
- EK-Quantum
Table of Contents
3831109901687 Velocity UNC Standoffs
User Guide EK-Quantum
Velocity UNC Standoffs
Please note the installation of the product is intended to be undertaken by an
adequately trained and experienced person. You are installing the product at
your own risk. If you are not properly trained or experienced or feel unsure
about the installation procedure, please refrain from installing the product
yourself and contact our tech support for assistance. We disclaim our
liability for any damages to the product as well as incidental, consequential,
or indirect damages incurred due to improper or inappropriate installation.
Before you start using this product, please follow these basic guidelines:
Please carefully read the manual before beginning the installation process.
The EK Fittings require only a small amount of force to screw them firmly in
place since the liquid seal is ensured by the rubber O-ring gaskets.
The use of corrosion-inhibiting coolants is always recommended for liquid
cooling systems, and mandatory for nickel-plated water blocks.
Do not use pure distilled water! For best results, EK recommends the use of
EK-Cryo Fuel coolants.
Make sure to thoroughly bleed air out of your water block, or you will not
reach optimal performance.
BOX CONTENTS
AM5 Mounting Standoff (4 pcs)
PREPARING THE AM4 WATER BLOCK FOR UPGRADE
Important! Before starting, make sure to have a clean, flat surface to
work on. It is recommended to put foam or soft material to lay a motherboard
on.
STEP 1
If the EK-Velocity AM4 water block is already installed, unscrew four (4)
Thumb Nuts to detach it (As shown in the picture). Save the Thumb Nuts and
springs for later use.
STEP 2
Clean the CPU cold plate using a non-abrasive cloth or Q-tip.
PREPARING THE AM5 MOTHERBOARD
STEP 1
Using a Philips-head screwdriver remove the four UNC 6-32 screws securing the
original plastic hold-down clamps around the socket as shown in the
illustration. Remove the hold-down clamps and store them away. STEP 2
Cleaning the CPU: Wipe the IHS clean using a non-abrasive cloth or Q-tip
as shown in the illustration.
STEP 3
Applying thermal compound: Apply the enclosed thermal grease (thermal
compound) on the CPU heat spreader – IHS – as shown in the image. The layer of
the thermal compound must be thin and even in thickness over the entire
surface of the IHS. **** The excessive or uneven application of thermal grease
may lead to poor performance!
For this step, you will need:
INSTALLING THE WATER BLOCK
STEP 1
Install four (4) AM5 Mounting screws onto your motherboard. It is mandatory to
put a saved plastic washer underneath each of the screws. Tighten the screws
until you reach the end of the thread. Using tools (such as pliers) is not
recommended. STEP 2
Align the water block over the mounting screws on the motherboard.
Place a saved compression spring and thumb nut over each AM5 Mounting screw.
Start fastening two thumb nuts at a time, preferably in a cross pattern, and
do not tighten them fully until all of them are partially screwed in. Then –
using your fingers only – screw in all four
thumb nuts until you reach the end of the thread.
CONNECTING THE D-RGB LED STRIP
STEP 1
Plug the 3-pin connector from the water block’s D-RGB LED light to the DRGB
HEADER on the motherboard. The LED will work if the pin layout on the header
is as follows: +5V, Digital, empty, Ground. Please ensure that the arrow
indicated on the connector is plugged into the +5V line as indicated on your
motherboard. If you put the LED Diode to the 12V RGB HEADER you can damage the
LEDs. Failure to do so will damage your motherboard or LED strip.
TESTING THE LOOP
To make sure the installation of EK components was successful, we recommend you perform a leak test for 24 hours. When your loop is complete and filled with coolant, connect the pump to a PSU outside of your system. Do not connect power to any of the other components. Turn on the PSU and let the pump run continuously. It is normal for the coolant level to drop during this process as air collects in the distribution plate. Inspect all parts of the loop, and in the eventuality that coolant leaks, fix the issue and repeat the testing process. Ensure that all hardware is dry before the system is powered on in order to prevent any damage.
WARRANTY
Our products are warranted against defects of materials and quality for a period of 24 months, starting with the date of delivery to the end-user. During this period, products will be repaired or have parts replaced at our discretion, provided that 1) the product is returned to the agent from whom it was purchased; 2) the product has been purchased by the end-user and has not been used for commercial purposes; 3) the product has not been misused, handled carelessly, or used in a manner other than the way described in the instructions manual. This warranty does not confer rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer. This warranty is voided if the product comes in contact with aggressive UV additives or other improper liquids. EK water blocks are sealed with a warranty-voiding circular label, proving the water block has withstood a pressure leak test. Removing the label will void the leak-free guarantee, but not the guarantee on the product itself. Any other RMA issues can be reported to EK Customer Support at www.ekwb.com/support for further analysis.
SUPPORT AND SERVICE
In case you need assistance or wish to order spare parts or a new mounting
mechanism, please contact: https://www.ekwb.com/customer-
support/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia – EU
SOCIAL MEDIA
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
EKWBofficial
ekwaterblocks
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>