EK-Loop 140-120mm Angled Bracket User Guide
- June 16, 2024
- EK-Loop
Table of Contents
- 140-120mm Angled Bracket
- BOX CONTENTS
- ASSEMBLING THE EK-LOOP ANGLED BRACKET
- INSTALLING THE EK-LOOP ANGLED BRACKET DIRECTLY INTO THE CASE
- INSTALLING THE EK-LOOP ANGLED BRACKET ONTO THE RADIATOR
- ATTACHING THE RESERVOIR TO THE EK-LOOP ANGLED BRACKET
- ATTACHING THE FITTINGS
- SUPPORT AND SERVICE
- SOCIAL MEDIA
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Angled Bracket – 140/120 mm
140-120mm Angled Bracket
USER GUIDE
This product is intended for installation by expert users only. Please consult
with a qualified technician for installation. Improper installation may result
in damage to your equipment. EK Water Blocks assumes no liability whatsoever,
expressed or implied, for the use of these products, nor their installation.
The following instructions are subject to change without notice. Please visit
our web site at www.ekwb.com for updates. Before
installation, please read important notice, disclosure, and warranty
conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
Please, read the manual carefully before you begin with the installation
process!
EK-Loop Angled Bracket – 140/120mm is compatible with EKQuantum Kinetic FLT
and EK-Quantum Volume FLT units.
BOX CONTENTS
ASSEMBLING THE EK-LOOP ANGLED BRACKET
EK-Loop Angled Bracket base piece has four slot holes that allow adjustability. Larger slot holes will enable adjusting of the bracket’s position (63 mm on each side). Side pieces can be screwed into the base through one of the slots or both of them.Smaller slot holes on the side allow for adjusting the position of the bracket on the radiator.![EK-Loop 140-120mm Angled Bracket
- parts3](https://manuals.plus/wp-content/uploads/2024/01/EK-Loop-140-120mm- Angled-Bracket-parts3.jpg)For the assembly of the EK-Loop Angled Bracket – 140/120 mm, use M4 x 4 DIN 7984 screws (as shown in the picture). Side parts already have threaded holes, so there is no need for additional washers and nuts.
INSTALLING THE EK-LOOP ANGLED BRACKET DIRECTLY INTO THE CASE
EK-Loop Angled Bracket – 140/120 mm can be mount directly into the case when
there is a place for a 140 mm fan.
The 120 mm format FLT reservoir can also be mounted onto the EK-Loop Angled
Bracket and secured together into the chassis.
Alternatively, you can drill four Ø4.5mm holes in the most suitable place on
the wall of your computer chassis, using the electric power drill.
EK-Loop Angled Bracket – 140/120 mm can be installed directly into the
chassis, using the enclosed M4 x 10 DIN7984 screws, M4 steel washers, and M4
nuts (as shown in the picture).After securing the EK-Loop Angled Bracket – 140/120
mm into the chassis, you can attach the FLT reservoir. (See chapter: Attaching
the Reservoir to the EK-Loop Angled Bracket)
INSTALLING THE EK-LOOP ANGLED BRACKET ONTO THE RADIATOR
EK-Loop Angled Bracket – 140/120 mm can be mounted onto the 140 mm format
radiator using the M4 x 5 mm Phillips head radiator mounting screws (as shown
in the picture). There is no need for additional nuts, just tighten the screws
evenly and do not use excessive force.
Beacause this this configuration serves as an adapter from 140 mm radiator to
120 mm format reservoir, the base brackets need to be rotated as shown on the
picture.
The configuration also limits the use of the slots on the angled bracket base
parts. Especially if the bracket base is located by the inlet and the outlet
ports of the radiator.You can mount the bracket on each side of the
radiator. On 280 and 420 mm radiators, the bracket can also be attached to the
middle holes.
ATTACHING THE RESERVOIR TO THE EK-LOOP ANGLED BRACKET
Carefully position the 120 format FLT reservoir onto the EK-Loop angled bracket and secure it with the enclosed M4 x 10 DIN 7984 screws and acetal standoffs (as shown in the picture). While tightening the screws, do not use excessive force. Make sure that all four (4) screws and standoffs are adequately secured!If you choose to use the holes in the middle, it is no longer possible to move the FLT reservoir from or toward the radiator!
ATTACHING THE FITTINGS
When using the EK-Loop Angled Bracket with FLT products, we recommend you use
EK-Fittings because of their compatibility, and there will be no reason to
worry.
Before you attach the fittings, make sure the acetal standoffs are placed
correctly. Otherwise, you risk the possibility of scratching your FLT product
(especially when using EK-Torque HTC-16 Fittings).
SUPPORT AND SERVICE
For assistance please contact: http://support.ekwb.com/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia – EU
SOCIAL MEDIA
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
EKWBofficial
ekwaterblocks
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>