EK-Quantum Convection DDC Pump Heatsink User Guide
- June 4, 2024
- EK-Quantum
Table of Contents
EK-Quantum Convection DDC Pump Heatsink
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the installation process.
BOX CONTENTS
DDC COVER DIMENSIONS
MAIN PARTS
Position
|
EAN
| Description
---|---|---
1
|
103328
| ALU – FLT DDC Cover (Black Elox)
103327
| ALU – FLT DDC Cover (Nickel)
103570
| ALU – FLT DDC Cover (Natur Elox)
105059
| ALU – FLT DDC Cover (Gold)
2
|
100663
| EK RGB Badge
3
|
103331
| MS – FLT DDC Cover Screw M4 x 34 (Black Chrome)
103330
| MS – FLT DDC Cover Screw M4 x 34 (Nickel)
105359
| FLT DDC Cover Screw M4 x 34 (Gold)
4
|
8628
| Blažilnik M4 – Pump Top Mount (V2)
5
|
103578
| Kinetic DDC M4 x 59 Screw (Black Chrome)
103577
| Kinetic DDC M4 x 59 Screw (Nickel)
105361
| Kinetic DDC M4 x 59 Screw (Gold)
PREPARING THE DDC PUMP
STEP 1
Remove the original four (4) M4 x 25 screws of the DDC pump so that the
original cover can be removed from the assembly.
STEP 2
Then to remove the original pump cover, we recommend holding the pump onto the
reservoir by pressing the pattern in the middle. Then, while pressing the pump
onto the reservoir, remove the original cover of the pump. If by accident the
whole DDC pump is removed or detached, please make sure that the O-ring seals
are still properly mounted. Any misplaced O-ring seal will cause coolant
leakage!
If you are using EK-DDC Heatsink Housing, care for the thermal pad between the DDC pump and the housing!
INSTALLING THE EK-QUANTUM CONVECTION DDC
STEP 1
EK has supplied you with additional pre-cut thermal pad. Place the pre-cut
thermal pad on the DDC pump by aligning the shape of the pad to the DDC pump’s
PCB.
Then place the EK-Quantum Convection DDC onto the DDC pump.
Be careful to rotate the ALU Cover so that the cables of the pump are placed
properly.
STEP 2
Place the four (4) custom made M4 x 34 screws in their holes and secure them
with provided 2.5 mm Allen key. Do not use excessive force while tightening
the screws!
STEP 3
Following the same instructions for removing the original cover of the DDC
pump from the EK-Quantum Kinetic TBE DDC Series.
Then use the supplied 2 mm Allen Key for tightening four (4) Dumper Kinetic
DDC M4 x 59 Screws. Do not use excessive force while tightening the screws! EK
has also supplied you with four (4) vibration absorbing M4 – Pump Top Mount
Dumpers that can be tightened on the M4 x 59 screws as shown on the picture.
SUPPORT AND SERVICE
In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer- support/
For spare parts orders, refer to the page with “MAIN PARTS” where you can find the EAN number of each part you might need.
Include the EAN number with quantity in your request. Mounting Mechanism EAN can be found under “BOX CONTENTS”
Thermal pads are readily available in the EK shop
SOCIAL MEDIA
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>