AIGOSTAR 100801WNX LED Strip Light Instruction Manual

AIGOSTAR 100801WNX LED Strip Light

Please read this manual carefully before operating your product. Even you pass your product to others, please also follow below instructions and operate safety. We are not take responsibility like improper use or not to follow this operation manual and safety advice lead to damage to property or even injury to persons. Any warranty claim is also deemed as void.

Please check whether the product is complete. If you find any defects, please contact salesman immediately and make sure the package is ok.

PARTS

• Led strip lights 5m*2
  

• Controller

• Remote control (CR2025,3V button battery included)

• Adapter
  

• 2pcs screws and 1 pc adhesive tape

• 8pcs wire clips

• DIV strip connectors:

• 1 pc T-shape connectors
  

• 2pcs 4pin connectors

Note:

1. The way to test the photoelectricity parameter value of the product: Take 0.5m strip light and test it with12V DC power supply, and read the bare light source data.
2. Test conclusion:

Goods Code

| DC Voltage| Power
---|---|---
100801WNX| 12V|

1.8W

3. Class II

WARNING

1. THE PRODUCT IS NOT A TOY, PLEASE TAKE THE PRODUCT AND PACKAGE FAR AWAY FROM ADULT OR CHILDREN WHO CAN NOT EVALUATE THE RISK.
2. THE PRODUCT NEED TO INSTALL BY QUALIFIED ELECTRICIAN AND INSTALLED IN ACCORDANCE WITHLOCAL REQUIREMENTS.
3. PLEASE TURN OFF THE POWER SUPPLY BEFORE ANY OPERATIONS.
4. DO NOT LOOK DIRECTLY INTO THE LIGHT.
5. THE PRODUCT NEED TO BE CLEANED CORRECTLY. AVOID CLEANING THE PRODUCT WITH SHARP OR ABRASIVE DETERGENT.
6. ELECTRONIC WASTE AND ELECTRONIC DEVICE CANNOT DISPOSE WITH ORDINARY HOUSEHOLD WASTE.
7. THE REMOTE CONTROL CONTAIN NON-RECHARGEABLE BATTERIES, PLEASE MAKE SURE KEEP AND DISPOSE IT CAREFULLY. DO NOT THROW WASH IMMEDIATELY WITH PLENTY OF WATER.

Parameter

• Battery tape: CR 2025 3V
• Remote control range: Max 5M

Replace the battery of remote control:

We suggest to replace the battery when the remote control performance reduction. Before insert the battery, please make sure the touch point between remote control and battery are clean. And clean them if necessary.

1. Slide the battery cover in the arrow direction indicated and disassemble.
2. Take down the exhausted battery and install new battery(CR 2025) if necessary. Please pay attention to polarity(+/-) when replacing batteries.
3. Install the battery into remote control.

Installation

1. Clean the surface
2. Measure the desired length
3. Cut to size(It should be operated in the place where marked scissors, and the interval of 100mm can be cut).
4. Peel off protective foil
5. Stick the strip in place
6. Connect the strip to the DC adapter Remote control instructions

The remote control uses a CR2025 3V button battery. The remote control is on automatic standby mode when not in use. Normally the battery can be used for more than six months. The battery can be replaced by the same type. The remote control keys can be divided into three parts.

①② Brightness Adjust
③ Pause/Play
④ On/Off
⑤ 20 buttons. Click to display a single color.
⑥⑦ CV To adjust the speed of color changing.
⑧ Auto mode including
⑨ Flash mode: Click to make the white color flash. The white color only.
⑩⑪ Fade mode: Loop play 3 or 7 default colors in fading pattern.
⑫⑬ Jump mode: Loop play 3 or 7 default colors in jumping pattern.
⑭⑮ Set up DIY colors color setting.
Step 1: Click a DIY colors
Step 2: Press the arrow buttons to adjust to the color you like.
Step 3: Press the same DIV button again to save the color setting.

2-year quality guarantee under the correct operations.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>